Patches by Martin Krause, 22 Mar 2005:
- use TQM5200_auto as MAKEALL target for TQM5200 systems
- add support for SM501 graphics controller
- add support for graphic console on TQM5200
- add support for TQM5200 Rev 200
- cleanup, fix typo in include/configs/TQM5200.h
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 87bcc5b..a5a6344 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -1,8 +1,8 @@
/*
- * (C) Copyright 2003-2004
+ * (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * (C) Copyright 2004
+ * (C) Copyright 2004-2005
* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
*
* See file CREDITS for list of people who contributed to this
@@ -35,6 +35,7 @@
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
+#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
@@ -62,7 +63,6 @@
#define CONFIG_BOARD_EARLY_INIT_R
#endif /* CONFIG_STK52XX */
-#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
/*
* PCI Mapping:
* 0x40000000 - 0x4fffffff - PCI Memory
@@ -70,9 +70,6 @@
*/
#ifdef CONFIG_STK52XX
#define CONFIG_PCI 1
-#elif
-#define CONFIG_PCI 0
-#endif
#define CONFIG_PCI_PNP 1
/* #define CONFIG_PCI_SCAN_SHOW 1 */
@@ -89,21 +86,37 @@
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#ifdef CONFIG_STK52XX
+#ifdef CONFIG_PCI
#define ADD_PCI_CMD CFG_CMD_PCI
-#elif
+#else
#define ADD_PCI_CMD 0
#endif
-#else /* MPC5100 */
+/*
+ * Video console
+ */
+#if 1
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_SM501
+#define CONFIG_VIDEO_SM501_32BPP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+#endif
-#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
-
+#ifdef CONFIG_VIDEO
+#define ADD_BMP_CMD CFG_CMD_BMP
+#else
+#define ADD_BMP_CMD 0
#endif
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
/* USB */
#ifdef CONFIG_STK52XX
@@ -138,6 +151,7 @@
* Supported commands
*/
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ ADD_BMP_CMD | \
ADD_IDE_CMD | \
ADD_PCI_CMD | \
ADD_USB_CMD | \
@@ -173,7 +187,7 @@
#undef CONFIG_BOOTARGS
#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX "-AA"
+# define CONFIG_U_BOOT_SUFFIX "-AA\0"
#elif defined (CONFIG_TQM5200_AB)
# define CONFIG_U_BOOT_SUFFIX "-AB\0"
#elif defined (CONFIG_TQM5200_AC)
@@ -227,10 +241,10 @@
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#if defined (CONFIG_MINIFAP)
-#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#ifdef CONFIG_TQM5200_REV100
+#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
#else
-#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */
+#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
#endif
/*
@@ -288,8 +302,9 @@
#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_SIZE 0x02000000 /* 32 MByte */
-#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
+#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
#if !defined(CFG_LOWBOOT)
#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
@@ -357,27 +372,33 @@
* use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
* Bit 0 (mask: 0x80000000): 1
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
- * 00 -> No Alternatives, I2C1 is used for onboard EEPROM
- * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
- * EEPROM
+ * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
+ * Set for rev 100 modules with an onboard EEPROM (because,
+ * there I2C1 is used as I2C bus)
+ * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
+ * Set for rev 200 modules
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
* use PSC6:
* on STK52xx:
- * use as UART. Pins PSC6_0 to PSC6_3 are used.
- Bits 9:11 (mask: 0x00700000):
+ * use as UART. Pins PSC6_0 to PSC6_3 are used.
+ * Bits 9:11 (mask: 0x00700000):
* 101 -> PSC6 : Extended POST test is not available
* on MINI-FAP and TQM5200_IB:
- * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
- * 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
- * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- * tests.
+ * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
+ * 000 -> PSC6 could not be used as UART, CODEC or IrDA
+ * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
+ * tests.
*/
#if defined (CONFIG_MINIFAP)
-#define CFG_GPS_PORT_CONFIG 0x91300004
+# define CFG_GPS_PORT_CONFIG 0x91000004
#elif defined (CONFIG_STK52XX)
-#define CFG_GPS_PORT_CONFIG 0x81500004
-#else
-#define CFG_GPS_PORT_CONFIG 0x81300004
+# if defined (CONFIG_TQM5200_REV100)
+# define CFG_GPS_PORT_CONFIG 0x81500004
+# else
+# define CFG_GPS_PORT_CONFIG 0x91500004
+# endif
+#else /* TMQ5200_IP */
+# define CFG_GPS_PORT_CONFIG 0x81000004
#endif
/*
@@ -461,14 +482,15 @@
*/
#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
defined (CONFIG_CS_AUTOCONF)
-#define CFG_CS1_START 0xE0000000
+#define SM501_FB_BASE 0xE0000000
+#define CFG_CS1_START (SM501_FB_BASE)
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
#define CFG_CS1_CFG 0x8F48FF70
#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
#endif
#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333333
+#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
#define CFG_RESET_ADDRESS 0xff000000
@@ -493,7 +515,7 @@
#define CONFIG_IDE_PREINIT
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
#define CFG_ATA_IDE0_OFFSET 0x0000