Import <linux/mii.h> from the Linux kernel

Instead of creating yet another set of MII register definitions
in the macb driver, here's a complete set of definitions for everyone
to use.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
diff --git a/include/linux/mii.h b/include/linux/mii.h
new file mode 100644
index 0000000..5b99168
--- /dev/null
+++ b/include/linux/mii.h
@@ -0,0 +1,158 @@
+/*
+ * linux/mii.h: definitions for MII-compatible transceivers
+ * Originally drivers/net/sunhme.h.
+ *
+ * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
+ */
+
+#ifndef __LINUX_MII_H__
+#define __LINUX_MII_H__
+
+/* Generic MII registers. */
+
+#define MII_BMCR            0x00        /* Basic mode control register */
+#define MII_BMSR            0x01        /* Basic mode status register  */
+#define MII_PHYSID1         0x02        /* PHYS ID 1                   */
+#define MII_PHYSID2         0x03        /* PHYS ID 2                   */
+#define MII_ADVERTISE       0x04        /* Advertisement control reg   */
+#define MII_LPA             0x05        /* Link partner ability reg    */
+#define MII_EXPANSION       0x06        /* Expansion register          */
+#define MII_DCOUNTER        0x12        /* Disconnect counter          */
+#define MII_FCSCOUNTER      0x13        /* False carrier counter       */
+#define MII_NWAYTEST        0x14        /* N-way auto-neg test reg     */
+#define MII_RERRCOUNTER     0x15        /* Receive error counter       */
+#define MII_SREVISION       0x16        /* Silicon revision            */
+#define MII_RESV1           0x17        /* Reserved...                 */
+#define MII_LBRERROR        0x18        /* Lpback, rx, bypass error    */
+#define MII_PHYADDR         0x19        /* PHY address                 */
+#define MII_RESV2           0x1a        /* Reserved...                 */
+#define MII_TPISTATUS       0x1b        /* TPI status for 10mbps       */
+#define MII_NCONFIG         0x1c        /* Network interface config    */
+
+/* Basic mode control register. */
+#define BMCR_RESV               0x003f  /* Unused...                   */
+#define BMCR_SPEED1000		0x0040  /* MSB of Speed (1000)         */
+#define BMCR_CTST               0x0080  /* Collision test              */
+#define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
+#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
+#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII */
+#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840       */
+#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
+#define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
+#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
+#define BMCR_RESET              0x8000  /* Reset the DP83840           */
+
+/* Basic mode status register. */
+#define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
+#define BMSR_JCD                0x0002  /* Jabber detected             */
+#define BMSR_LSTATUS            0x0004  /* Link status                 */
+#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
+#define BMSR_RFAULT             0x0010  /* Remote fault detected       */
+#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
+#define BMSR_RESV               0x07c0  /* Unused...                   */
+#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
+#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
+#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets  */
+
+/* Advertisement control register. */
+#define ADVERTISE_SLCT          0x001f  /* Selector bits               */
+#define ADVERTISE_CSMA          0x0001  /* Only selector supported     */
+#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex  */
+#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
+#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex */
+#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex */
+#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets  */
+#define ADVERTISE_RESV          0x1c00  /* Unused...                   */
+#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults    */
+#define ADVERTISE_LPACK         0x4000  /* Ack link partners response  */
+#define ADVERTISE_NPAGE         0x8000  /* Next page bit               */
+
+#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
+			ADVERTISE_CSMA)
+#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
+                       ADVERTISE_100HALF | ADVERTISE_100FULL)
+
+/* Link partner ability register. */
+#define LPA_SLCT                0x001f  /* Same as advertise selector  */
+#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex   */
+#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex   */
+#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex  */
+#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex  */
+#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets   */
+#define LPA_RESV                0x1c00  /* Unused...                   */
+#define LPA_RFAULT              0x2000  /* Link partner faulted        */
+#define LPA_LPACK               0x4000  /* Link partner acked us       */
+#define LPA_NPAGE               0x8000  /* Next page bit               */
+
+#define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
+#define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)
+
+/* Expansion register for auto-negotiation. */
+#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego      */
+#define EXPANSION_LCWP          0x0002  /* Got new RX page code word   */
+#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words    */
+#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage */
+#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
+#define EXPANSION_RESV          0xffe0  /* Unused...                   */
+
+/* N-way test register. */
+#define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
+#define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
+#define NWAYTEST_RESV2          0xfe00  /* Unused...                   */
+
+
+/**
+ * mii_nway_result
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * Given a set of MII abilities, check each bit and returns the
+ * currently supported media, in the priority order defined by
+ * IEEE 802.3u.  We use LPA_xxx constants but note this is not the
+ * value of LPA solely, as described above.
+ *
+ * The one exception to IEEE 802.3u is that 100baseT4 is placed
+ * between 100T-full and 100T-half.  If your phy does not support
+ * 100T4 this is fine.  If your phy places 100T4 elsewhere in the
+ * priority order, you will need to roll your own function.
+ */
+static inline unsigned int mii_nway_result (unsigned int negotiated)
+{
+	unsigned int ret;
+
+	if (negotiated & LPA_100FULL)
+		ret = LPA_100FULL;
+	else if (negotiated & LPA_100BASE4)
+		ret = LPA_100BASE4;
+	else if (negotiated & LPA_100HALF)
+		ret = LPA_100HALF;
+	else if (negotiated & LPA_10FULL)
+		ret = LPA_10FULL;
+	else
+		ret = LPA_10HALF;
+
+	return ret;
+}
+
+/**
+ * mii_duplex
+ * @duplex_lock: Non-zero if duplex is locked at full
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * A small helper function for a common case.  Returns one
+ * if the media is operating or locked at full duplex, and
+ * returns zero otherwise.
+ */
+static inline unsigned int mii_duplex (unsigned int duplex_lock,
+				       unsigned int negotiated)
+{
+	if (duplex_lock)
+		return 1;
+	if (mii_nway_result(negotiated) & LPA_DUPLEX)
+		return 1;
+	return 0;
+}
+
+
+#endif /* __LINUX_MII_H__ */