board: ge: bx50v3: Enable DM PWM for backlight
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
index 4a75c7b..a29fc42 100644
--- a/board/ge/bx50v3/bx50v3.c
+++ b/board/ge/bx50v3/bx50v3.c
@@ -37,6 +37,7 @@
#include "../common/vpd_reader.h"
#include "../../../drivers/net/e1000.h"
#include <pci.h>
+#include <panel.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -124,16 +125,20 @@
}
#if defined(CONFIG_VIDEO_IPUV3)
-static iomux_v3_cfg_t const backlight_pads[] = {
- /* Power for LVDS Display */
- MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
- /* Backlight enable for LVDS display */
- MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
-#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
- /* backlight PWM brightness control */
- MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
+static void do_enable_backlight(struct display_info_t const *dev)
+{
+ struct udevice *panel;
+ int ret;
+
+ ret = uclass_get_device(UCLASS_PANEL, 0, &panel);
+ if (ret) {
+ printf("Could not find panel: %d\n", ret);
+ return;
+ }
+
+ panel_set_backlight(panel, 100);
+ panel_enable_backlight(panel);
+}
static void do_enable_hdmi(struct display_info_t const *dev)
{
@@ -155,7 +160,7 @@
.addr = -1,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_lcd,
- .enable = NULL,
+ .enable = do_enable_backlight,
.mode = {
.name = "G121X1-L03",
.refresh = 60,
@@ -314,12 +319,6 @@
IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
(IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
-
- /* backlights off until needed */
- imx_iomux_v3_setup_multiple_pads(backlight_pads,
- ARRAY_SIZE(backlight_pads));
- gpio_request(LVDS_POWER_GP, "lvds_power");
- gpio_direction_input(LVDS_POWER_GP);
}
#endif /* CONFIG_VIDEO_IPUV3 */
@@ -476,9 +475,6 @@
setup_display_b850v3();
else
setup_display_bx50v3();
-
- gpio_request(LVDS_BACKLIGHT_GP, "lvds_backlight");
- gpio_direction_input(LVDS_BACKLIGHT_GP);
#endif
/* address of boot parameters */
@@ -590,51 +586,6 @@
}
#endif
-static int do_backlight_enable(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-#if CONFIG_IS_ENABLED(DM_VIDEO)
- int ret;
- struct udevice *dev;
-
-#ifdef CONFIG_VIDEO_IPUV3
- if (!is_b850v3()) {
- gpio_direction_output(LVDS_POWER_GP, 1);
-
- /* We need at least 200ms between power on and backlight on
- * as per specifications from CHI MEI
- */
- mdelay(250);
-
- /* enable backlight PWM 1 */
- pwm_init(0, 0, 0);
-
- /* duty cycle 5000000ns, period: 5000000ns */
- pwm_config(0, 5000000, 5000000);
-
- /* Backlight Power */
- gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
-
- pwm_enable(0);
- }
-#endif
-
- /* Probe, to find a video device to be used to show a message on
- * the vidconsole.
- */
- ret = uclass_get_device(UCLASS_VIDEO, 0, &dev);
- if (ret)
- return ret;
-#endif
-
- return 0;
-}
-
-U_BOOT_CMD(
- bx50_backlight_enable, 1, 1, do_backlight_enable,
- "enable Bx50 backlight",
- ""
-);
-
int board_fit_config_name_match(const char *name)
{
if (!vpd.is_read)
diff --git a/configs/ge_bx50v3_defconfig b/configs/ge_bx50v3_defconfig
index b19861c..49df9f6 100644
--- a/configs/ge_bx50v3_defconfig
+++ b/configs/ge_bx50v3_defconfig
@@ -31,6 +31,7 @@
# CONFIG_CMD_NFS is not set
CONFIG_CMD_BOOTCOUNT=y
CONFIG_CMD_CACHE=y
+CONFIG_CMD_CLS=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
@@ -74,9 +75,11 @@
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_PWM_IMX=y
+CONFIG_DM_PWM=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_DA9063=y
CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_DA9063=y
CONFIG_DM_RTC=y
CONFIG_RTC_RX8010SJ=y
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
index b9227fc..46a3c38 100644
--- a/include/configs/ge_bx50v3.h
+++ b/include/configs/ge_bx50v3.h
@@ -105,7 +105,7 @@
"setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
"echo reached failbootcmd; " \
- "bx50_backlight_enable; " \
+ "cls; " \
"setcurs 5 4; " \
"lcdputs \"Monitor failed to start. " \
"Try again, or contact GE Service for support.\"; " \