net: phy: Improve the Marvell 151x constants
Use some constants for the phy configuration instead of so many magic
numbers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 11aea9a..ab0c443 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -82,6 +82,21 @@
#define MIIM_88E1310_PHY_RGMII_CTRL 21
#define MIIM_88E1310_PHY_PAGE 22
+/* 88E151x PHY defines */
+/* Page 3 registers */
+#define MIIM_88E151x_LED_FUNC_CTRL 16
+#define MIIM_88E151x_LED_FLD_SZ 4
+#define MIIM_88E151x_LED0_OFFS (0 * MIIM_88E151x_LED_FLD_SZ)
+#define MIIM_88E151x_LED1_OFFS (1 * MIIM_88E151x_LED_FLD_SZ)
+#define MIIM_88E151x_LED0_ACT 3
+#define MIIM_88E151x_LED1_100_1000_LINK 6
+#define MIIM_88E151x_LED_TIMER_CTRL 18
+#define MIIM_88E151x_INT_EN_OFFS 7
+/* Page 18 registers */
+#define MIIM_88E151x_GENERAL_CTRL 20
+#define MIIM_88E151x_MODE_SGMII 1
+#define MIIM_88E151x_RESET_OFFS 15
+
/* Marvell 88E1011S */
static int m88e1011s_config(struct phy_device *phydev)
{
@@ -286,7 +301,7 @@
*/
/* EEE initialization */
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00ff);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00ff);
phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x214B);
phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2144);
phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x0C28);
@@ -295,21 +310,23 @@
phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x214D);
phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xCC0C);
phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2159);
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000);
/* SGMII-to-Copper mode initialization */
if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
/* Select page 18 */
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 18);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 18);
/* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */
- m88e1518_phy_writebits(phydev, 20, 0, 3, 1);
+ m88e1518_phy_writebits(phydev, MIIM_88E151x_GENERAL_CTRL,
+ 0, 3, MIIM_88E151x_MODE_SGMII);
/* PHY reset is necessary after changing MODE[2:0] */
- m88e1518_phy_writebits(phydev, 20, 15, 1, 1);
+ m88e1518_phy_writebits(phydev, MIIM_88E151x_GENERAL_CTRL,
+ MIIM_88E151x_RESET_OFFS, 1, 1);
/* Reset page selection */
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0);
udelay(100);
}
@@ -321,17 +338,25 @@
static int m88e1510_config(struct phy_device *phydev)
{
/* Select page 3 */
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 3);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE,
+ MIIM_88E1118_PHY_LED_PAGE);
/* Enable INTn output on LED[2] */
- m88e1518_phy_writebits(phydev, 18, 7, 1, 1);
+ m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_TIMER_CTRL,
+ MIIM_88E151x_INT_EN_OFFS, 1, 1);
/* Configure LEDs */
- m88e1518_phy_writebits(phydev, 16, 0, 4, 3); /* LED[0]:0011 (ACT) */
- m88e1518_phy_writebits(phydev, 16, 4, 4, 6); /* LED[1]:0110 (LINK) */
+ /* LED[0]:0011 (ACT) */
+ m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_FUNC_CTRL,
+ MIIM_88E151x_LED0_OFFS, MIIM_88E151x_LED_FLD_SZ,
+ MIIM_88E151x_LED0_ACT);
+ /* LED[1]:0110 (LINK 100/1000 Mbps) */
+ m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_FUNC_CTRL,
+ MIIM_88E151x_LED1_OFFS, MIIM_88E151x_LED_FLD_SZ,
+ MIIM_88E151x_LED1_100_1000_LINK);
/* Reset page selection */
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0);
return m88e1518_config(phydev);
}