Coding Style cleanup: replace leading SPACEs by TABs
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
diff --git a/doc/README.mxsimage b/doc/README.mxsimage
index 88a2caf..0d31cba 100644
--- a/doc/README.mxsimage
+++ b/doc/README.mxsimage
@@ -10,7 +10,7 @@
To generate an image, write an image configuration file and run:
mkimage -A arm -O u-boot -T mxsimage -n <path to configuration file> \
- <output bootstream file>
+ <output bootstream file>
The output bootstream file is usually using the .sb file extension. Note
that the example configuration files for producing bootable BootStream with
@@ -54,33 +54,33 @@
LOAD u32_address string_filename
- Instructs the BootROM to load file pointed by "string_filename" onto
- address "u32_address".
+ address "u32_address".
LOAD IVT u32_address u32_IVT_entry_point
- Crafts and loads IVT onto address "u32_address" with the entry point
- of u32_IVT_entry_point.
+ of u32_IVT_entry_point.
- i.MX28-specific instruction!
LOAD DCD u32_address u32_DCD_block_ID
- Loads the DCD block with ID "u32_DCD_block_ID" onto address
- "u32_address" and executes the contents of this DCD block
+ "u32_address" and executes the contents of this DCD block
- i.MX28-specific instruction!
FILL u32_address u32_pattern u32_length
- Starts to write memory from addres "u32_address" with a pattern
- specified by "u32_pattern". Writes exactly "u32_length" bytes of the
+ specified by "u32_pattern". Writes exactly "u32_length" bytes of the
pattern.
JUMP [HAB] u32_address [u32_r0_arg]
- Jumps onto memory address specified by "u32_address" by setting this
- address in PT. The BootROM will pass the "u32_r0_arg" value in ARM
+ address in PT. The BootROM will pass the "u32_r0_arg" value in ARM
register "r0" to the executed code if this option is specified.
Otherwise, ARM register "r0" will default to value 0x00000000. The
optional "HAB" flag is i.MX28-specific flag turning on the HAB boot.
CALL [HAB] u32_address [u32_r0_arg]
- See JUMP instruction above, as the operation is exactly the same with
- one difference. The CALL instruction does allow returning into the
+ one difference. The CALL instruction does allow returning into the
BootROM from the executed code. U-Boot makes use of this in it's SPL
code.
@@ -88,10 +88,10 @@
- Restart the CPU and start booting from device specified by the
"string_mode" argument. The "string_mode" differs for each CPU
and can be:
- i.MX23, string_mode = USB/I2C/SPI1_FLASH/SPI2_FLASH/NAND_BCH
- JTAG/SPI3_EEPROM/SD_SSP0/SD_SSP1
- i.MX28, string_mode = USB/I2C/SPI2_FLASH/SPI3_FLASH/NAND_BCH
- JTAG/SPI2_EEPROM/SD_SSP0/SD_SSP1
+ i.MX23, string_mode = USB/I2C/SPI1_FLASH/SPI2_FLASH/NAND_BCH
+ JTAG/SPI3_EEPROM/SD_SSP0/SD_SSP1
+ i.MX28, string_mode = USB/I2C/SPI2_FLASH/SPI3_FLASH/NAND_BCH
+ JTAG/SPI2_EEPROM/SD_SSP0/SD_SSP1
- An optional "DCD" blocks can be added at the begining of the configuration
file. Note that the DCD is only supported on i.MX28.
@@ -99,7 +99,7 @@
configuration file.
- The DCD block has the following semantics:
- DCD u32_DCD_block_ID
+ DCD u32_DCD_block_ID
- u32_DCD_block_ID :: The ID number of the DCD block, must match
the ID number used by "LOAD DCD" instruction.