sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 64-bit ARM cores.
Only small cosmetic changes (clock name fixed), but we add the DT for
the new OrangePi Zero 3 board, for which U-Boot enablement patches are
pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi
index 135762b..2240eae 100644
--- a/arch/arm/dts/sun50i-a64.dtsi
+++ b/arch/arm/dts/sun50i-a64.dtsi
@@ -93,6 +93,7 @@
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
+ cache-unified;
};
};
@@ -407,7 +408,7 @@
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
clock-names = "ahb", "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
reset-names = "lcd", "lvds";
diff --git a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
index 686f58e..b710f1a 100644
--- a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
+++ b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2019 Corentin LABBE <clabbe@baylibre.com>
*/
diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
new file mode 100644
index 0000000..15290e6
--- /dev/null
+++ b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3.
+ * Excludes PMIC nodes and properties, since they are different between the two.
+ */
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: regulator-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ /*
+ * PHY0 pins are connected to a USB-C socket, but a role switch
+ * is not implemented: both CC pins are pulled to GND.
+ * The VBUS pins power the device, so a fixed peripheral mode
+ * is the best choice.
+ * The board can be powered via GPIOs, in this case port0 *can*
+ * act as a host (with a cable/adapter ignoring CC), as VBUS is
+ * then provided by the GPIOs. Any user of this setup would
+ * need to adjust the DT accordingly: dr_mode set to "host",
+ * enabling OHCI0 and EHCI0.
+ */
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
index cb8600d..d83852e 100644
--- a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
+++ b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
@@ -1,99 +1,23 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2020 Arm Ltd.
*/
/dts-v1/;
-#include "sun50i-h616.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/leds/common.h>
+#include "sun50i-h616-orangepi-zero.dtsi"
/ {
model = "OrangePi Zero2";
compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
-
- aliases {
- ethernet0 = &emac0;
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-0 {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_RED>;
- gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
- default-state = "on";
- };
-
- led-1 {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
- };
- };
-
- reg_vcc5v: vcc5v {
- /* board wide 5V supply directly from the USB-C socket */
- compatible = "regulator-fixed";
- regulator-name = "vcc-5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- reg_usb1_vbus: regulator-usb1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb1-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <®_vcc5v>;
- enable-active-high;
- gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
- };
};
-&ehci1 {
- status = "okay";
-};
-
-/* USB 2 & 3 are on headers only. */
-
&emac0 {
- pinctrl-names = "default";
- pinctrl-0 = <&ext_rgmii_pins>;
- phy-mode = "rgmii";
- phy-handle = <&ext_rgmii_phy>;
phy-supply = <®_dcdce>;
- allwinner,rx-delay-ps = <3100>;
- allwinner,tx-delay-ps = <700>;
- status = "okay";
-};
-
-&mdio0 {
- ext_rgmii_phy: ethernet-phy@1 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <1>;
- };
};
&mmc0 {
vmmc-supply = <®_dcdce>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
- bus-width = <4>;
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
};
&r_rsb {
@@ -211,44 +135,3 @@
vcc-ph-supply = <®_aldo1>;
vcc-pi-supply = <®_aldo1>;
};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
-
- flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <40000000>;
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
-};
-
-&usbotg {
- /*
- * PHY0 pins are connected to a USB-C socket, but a role switch
- * is not implemented: both CC pins are pulled to GND.
- * The VBUS pins power the device, so a fixed peripheral mode
- * is the best choice.
- * The board can be powered via GPIOs, in this case port0 *can*
- * act as a host (with a cable/adapter ignoring CC), as VBUS is
- * then provided by the GPIOs. Any user of this setup would
- * need to adjust the DT accordingly: dr_mode set to "host",
- * enabling OHCI0 and EHCI0.
- */
- dr_mode = "peripheral";
- status = "okay";
-};
-
-&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
- status = "okay";
-};
diff --git a/arch/arm/dts/sun50i-h616-x96-mate.dts b/arch/arm/dts/sun50i-h616-x96-mate.dts
index 07424c2..959b6fd 100644
--- a/arch/arm/dts/sun50i-h616-x96-mate.dts
+++ b/arch/arm/dts/sun50i-h616-x96-mate.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2021 Arm Ltd.
*/
diff --git a/arch/arm/dts/sun50i-h618-orangepi-zero3.dts b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts
new file mode 100644
index 0000000..00fe28c
--- /dev/null
+++ b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616-orangepi-zero.dtsi"
+
+/ {
+ model = "OrangePi Zero3";
+ compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
+};
+
+&emac0 {
+ phy-supply = <®_dldo1>;
+};
+
+&ext_rgmii_phy {
+ motorcomm,clk-out-frequency-hz = <125000000>;
+};
+
+&mmc0 {
+ /*
+ * The schematic shows the card detect pin wired up to PF6, via an
+ * inverter, but it just doesn't work.
+ */
+ broken-cd;
+ vmmc-supply = <®_dldo1>;
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp313: pmic@36 {
+ compatible = "x-powers,axp313a";
+ reg = <0x36>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&pio>;
+ interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>; /* PC9 */
+
+ vin1-supply = <®_vcc5v>;
+ vin2-supply = <®_vcc5v>;
+ vin3-supply = <®_vcc5v>;
+
+ regulators {
+ /* Supplies VCC-PLL, so needs to be always on. */
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ /* Supplies VCC-IO, so needs to be always on. */
+ reg_dldo1: dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-dram";
+ };
+ };
+ };
+};
+
+&pio {
+ vcc-pc-supply = <®_dldo1>;
+ vcc-pf-supply = <®_dldo1>;
+ vcc-pg-supply = <®_aldo1>;
+ vcc-ph-supply = <®_dldo1>;
+ vcc-pi-supply = <®_dldo1>;
+};
diff --git a/include/dt-bindings/clock/sun50i-h6-ccu.h b/include/dt-bindings/clock/sun50i-h6-ccu.h
index a1545cd..ef9123d 100644
--- a/include/dt-bindings/clock/sun50i-h6-ccu.h
+++ b/include/dt-bindings/clock/sun50i-h6-ccu.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*/
diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h
index 1191aca..6f8f01e 100644
--- a/include/dt-bindings/clock/sun50i-h616-ccu.h
+++ b/include/dt-bindings/clock/sun50i-h616-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2020 Arm Ltd.
*/
diff --git a/include/dt-bindings/clock/sun6i-rtc.h b/include/dt-bindings/clock/sun6i-rtc.h
index c845493..3bd3aa3 100644
--- a/include/dt-bindings/clock/sun6i-rtc.h
+++ b/include/dt-bindings/clock/sun6i-rtc.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
#ifndef _DT_BINDINGS_CLK_SUN6I_RTC_H_
#define _DT_BINDINGS_CLK_SUN6I_RTC_H_
diff --git a/include/dt-bindings/reset/sun50i-h6-ccu.h b/include/dt-bindings/reset/sun50i-h6-ccu.h
index 81106f4..d038ddf 100644
--- a/include/dt-bindings/reset/sun50i-h6-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h6-ccu.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*/
diff --git a/include/dt-bindings/reset/sun50i-h6-r-ccu.h b/include/dt-bindings/reset/sun50i-h6-r-ccu.h
index 7950e79..d541ade 100644
--- a/include/dt-bindings/reset/sun50i-h6-r-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h6-r-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
*/
diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h
index cb6285a..1bd8bb0 100644
--- a/include/dt-bindings/reset/sun50i-h616-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h616-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2020 Arm Ltd.
*/