Convert CONFIG_FSL_IFC to Kconfig
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/cpu/armv7/ls102xa/Kconfig b/arch/arm/cpu/armv7/ls102xa/Kconfig
index f919d02..6a948d7 100644
--- a/arch/arm/cpu/armv7/ls102xa/Kconfig
+++ b/arch/arm/cpu/armv7/ls102xa/Kconfig
@@ -1,5 +1,6 @@
config ARCH_LS1021A
bool
+ select FSL_IFC if !QSPI_BOOT && !SD_BOOT_QSPI
select SYS_FSL_DDR_BE if SYS_FSL_DDR
select SYS_FSL_DDR_VER_50 if SYS_FSL_DDR
select SYS_FSL_ERRATUM_A008378
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index a6ac897..cb968bc 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -59,6 +59,7 @@
bool
select ARMV8_SET_SMPEN
select ARM_ERRATA_855873 if !TFABOOT
+ select FSL_IFC if TFABOOT || (!QSPI_BOOT && !SD_BOOT_QSPI)
select FSL_LAYERSCAPE
select FSL_LSCH2
select GICV2
@@ -94,6 +95,7 @@
config ARCH_LS1046A
bool
select ARMV8_SET_SMPEN
+ select FSL_IFC if TFABOOT || (!QSPI_BOOT && !SD_BOOT_QSPI)
select FSL_LAYERSCAPE
select FSL_LSCH2
select GICV2
@@ -134,6 +136,7 @@
bool
select ARMV8_SET_SMPEN
select ARM_ERRATA_855873 if !TFABOOT
+ select FSL_IFC
select FSL_LAYERSCAPE
select FSL_LSCH3
select GICV3
@@ -182,6 +185,7 @@
select ARM_ERRATA_828024
select ARM_ERRATA_829520
select ARM_ERRATA_833471
+ select FSL_IFC
select FSL_LAYERSCAPE
select FSL_LSCH3
select GICV3
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index d71ca86..ef7a213 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -1084,9 +1084,6 @@
config SYS_PPC_E500_USE_DEBUG_TLB
bool
-config FSL_IFC
- bool
-
config FSL_ELBC
bool
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 33a8259..a8baaea 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -500,4 +500,7 @@
Support ESM (Error Signal Monitor) on PMIC devices. ESM is used
typically to reboot the board in error condition.
+config FSL_IFC
+ bool
+
endmenu
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index df9eae1..a4073b9 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -134,6 +134,7 @@
config NAND_FSL_IFC
bool "Support Freescale Integrated Flash Controller NAND driver"
+ select FSL_IFC
help
Enable the Freescale Integrated Flash Controller NAND driver.
diff --git a/include/configs/km/pg-wcom-ls102xa.h b/include/configs/km/pg-wcom-ls102xa.h
index 743d09e..32659db 100644
--- a/include/configs/km/pg-wcom-ls102xa.h
+++ b/include/configs/km/pg-wcom-ls102xa.h
@@ -40,7 +40,6 @@
* IFC Definitions
*/
/* NOR Flash Definitions */
-#define CONFIG_FSL_IFC
#define CONFIG_SYS_FLASH_BASE 0x60000000
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h
index 27b97ff..252e32f 100644
--- a/include/configs/ls1021aqds.h
+++ b/include/configs/ls1021aqds.h
@@ -76,7 +76,6 @@
* IFC Definitions
*/
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_FSL_IFC
#define CONFIG_SYS_FLASH_BASE 0x60000000
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h
index b7c2cd7..bbfee84 100644
--- a/include/configs/ls1021atwr.h
+++ b/include/configs/ls1021atwr.h
@@ -89,7 +89,6 @@
* IFC Definitions
*/
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_FSL_IFC
#define CONFIG_SYS_FLASH_BASE 0x60000000
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
index b3f9117..0975c74 100644
--- a/include/configs/ls1043a_common.h
+++ b/include/configs/ls1043a_common.h
@@ -122,7 +122,6 @@
#ifndef SPL_NO_IFC
#if defined(CONFIG_TFABOOT) || \
(!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI))
-#define CONFIG_FSL_IFC
/*
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
diff --git a/include/configs/ls1046afrwy.h b/include/configs/ls1046afrwy.h
index fa37c68..4725503 100644
--- a/include/configs/ls1046afrwy.h
+++ b/include/configs/ls1046afrwy.h
@@ -17,8 +17,6 @@
#define CONFIG_SYS_UBOOT_BASE 0x40100000
-/* IFC */
-#define CONFIG_FSL_IFC
/*
* NAND Flash Definitions
*/
diff --git a/include/configs/ls1046aqds.h b/include/configs/ls1046aqds.h
index 3a502bc..c032ebe 100644
--- a/include/configs/ls1046aqds.h
+++ b/include/configs/ls1046aqds.h
@@ -43,7 +43,6 @@
/* IFC */
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_FSL_IFC
/*
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
diff --git a/include/configs/ls1046ardb.h b/include/configs/ls1046ardb.h
index c27eb73..4fc954c 100644
--- a/include/configs/ls1046ardb.h
+++ b/include/configs/ls1046ardb.h
@@ -27,14 +27,6 @@
#define CONFIG_SYS_SPL_ARGS_ADDR 0x90000000
#endif
-#ifndef SPL_NO_IFC
-/* IFC */
-#define CONFIG_FSL_IFC
-/*
- * NAND Flash Definitions
- */
-#endif
-
#define CONFIG_SYS_NAND_BASE 0x7e800000
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
diff --git a/include/configs/ls1088a_common.h b/include/configs/ls1088a_common.h
index 140362c..93edaaa 100644
--- a/include/configs/ls1088a_common.h
+++ b/include/configs/ls1088a_common.h
@@ -63,11 +63,6 @@
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
-#if !defined(SPL_NO_IFC) || defined(CONFIG_TARGET_LS1088AQDS)
-/* IFC */
-#define CONFIG_FSL_IFC
-#endif
-
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index 0ca03e0..cd58ee5 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -74,9 +74,6 @@
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
-/* IFC */
-#define CONFIG_FSL_IFC
-
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet