configs: starfive: Enable ID EEPROM configuration
Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-By: Leo Yu-Chi Linag <ycliang@andestech.com>
diff --git a/configs/starfive_visionfive2_defconfig b/configs/starfive_visionfive2_defconfig
index c577081..570a1f5 100644
--- a/configs/starfive_visionfive2_defconfig
+++ b/configs/starfive_visionfive2_defconfig
@@ -13,6 +13,7 @@
CONFIG_OF_LIBFDT_OVERLAY=y
CONFIG_DM_RESET=y
CONFIG_SPL_MMC=y
+CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL_STACK=0x8180000
CONFIG_SPL=y
CONFIG_SPL_SPI_FLASH_SUPPORT=y
@@ -23,6 +24,7 @@
CONFIG_ARCH_RV64I=y
CONFIG_CMODEL_MEDANY=y
CONFIG_RISCV_SMODE=y
+# CONFIG_OF_BOARD_FIXUP is not set
CONFIG_FIT=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_QSPI_BOOT=y
@@ -34,6 +36,8 @@
CONFIG_DEFAULT_FDT_FILE="starfive/jh7110-starfive-visionfive-2.dtb"
CONFIG_DISPLAY_CPUINFO=y
CONFIG_DISPLAY_BOARDINFO=y
+CONFIG_ID_EEPROM=y
+CONFIG_SYS_EEPROM_BUS_NUM=5
CONFIG_SPL_MAX_SIZE=0x40000
CONFIG_SPL_PAD_TO=0x0
CONFIG_SPL_BSS_START_ADDR=0x8040000
@@ -45,21 +49,34 @@
CONFIG_SYS_SPL_MALLOC_SIZE=0x400000
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2
+CONFIG_SPL_I2C=y
CONFIG_SPL_DM_SPI_FLASH=y
CONFIG_SPL_DM_RESET=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_CBSIZE=256
CONFIG_SYS_PBSIZE=276
CONFIG_SYS_BOOTM_LEN=0x4000000
+CONFIG_CMD_EEPROM=y
+CONFIG_SYS_EEPROM_SIZE=512
+CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=4
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_I2C=y
CONFIG_CMD_TFTPPUT=y
+CONFIG_OF_BOARD=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_REGMAP=y
CONFIG_SYSCON=y
CONFIG_SPL_CLK_COMPOSITE_CCF=y
CONFIG_CLK_COMPOSITE_CCF=y
CONFIG_SPL_CLK_JH7110=y
-# CONFIG_I2C is not set
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_DW=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_SPL_I2C_EEPROM=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0X50
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_SPL_MMC_HS400_SUPPORT=y
CONFIG_MMC_DW=y