EXYNOS5: Add device node for FIMD
Add DT node and bindings documentation for FIMD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
diff --git a/arch/arm/dts/exynos5250.dtsi b/arch/arm/dts/exynos5250.dtsi
index 61d35a8..cfc9062 100644
--- a/arch/arm/dts/exynos5250.dtsi
+++ b/arch/arm/dts/exynos5250.dtsi
@@ -156,4 +156,10 @@
reg = <0x10060000 0x10000>;
};
+ fimd@14400000 {
+ compatible = "samsung,exynos-fimd";
+ reg = <0x14400000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
};
diff --git a/doc/device-tree-bindings/video/exynos-fb.txt b/doc/device-tree-bindings/video/exynos-fb.txt
new file mode 100644
index 0000000..bb7441c
--- /dev/null
+++ b/doc/device-tree-bindings/video/exynos-fb.txt
@@ -0,0 +1,92 @@
+Exynos Display Controller
+=========================
+Required properties:
+SOC specific:
+ compatible: should be "samsung,exynos-fimd"
+ reg: Base address of FIMD IP.
+
+Board(panel specific):
+ samsung,vl-col: X resolution of the panel
+ samsung,vl-row: Y resolution of the panel
+ samsung,vl-freq: Refresh rate
+ samsung,vl-bpix: Bits per pixel
+ samsung,vl-hspw: Hsync value
+ samsung,vl-hfpd: Right margin
+ samsung,vl-hbpd: Left margin
+ samsung,vl-vspw: Vsync value
+ samsung,vl-vfpd: Lower margin
+ samsung,vl-vbpd: Upper margin
+
+Optional properties:
+Board(panel specific):
+ samsung,vl-width: width of display area in mm
+ samsung,vl-height: Height of display area in mm
+
+ samsung,vl-clkp: Clock polarity
+ CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
+ samsung,vl-oep: Output Enable polarity
+ CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
+ samsung,vl-hsp: Horizontal Sync polarity
+ CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
+ samsung,vl-vsp: Vertical Sync polarity
+ CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
+ samsung,vl-dp: Data polarity
+ CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH
+
+ samsung,vl-cmd-allow-len: Wait end of frame
+ samsung,winid: Window number on which data is to be displayed
+ samsung,init-delay: Delay before LCD initialization starts
+ samsung,power-on-delay: Delay after LCD is powered on
+ samsung,reset-delay: Delay after LCD is reset
+ samsung,interface-mode: 1(FIMD_RGB_INTERFACE), 2(FIMD_CPU_INTERFACE)
+ samsung,mipi-enabled: 1 if you want to use MIPI, else 0
+ samsung,dp-enabled: 1is you want to use DP, else 0
+ samsung,cs-setup: cs_setup value in FIMD_CPU_INTERFACE mode.
+ samsung,wr-setup: wr_setup value in FIMD_CPU_INTERFACE mode.
+ samsung,wr-act: wr_act value in FIMD_CPU_INTERFACE mode.
+ samsung,wr-hold: wr_hold value in FIMD_CPU_INTERFACE mode.
+ samsung,logo-on: 1 if you want to use custom logo.
+ 0 if you want LCD console.
+ samsung,logo-width: pixel width of logo image. Valid if logo_on = 1
+ samsung,logo-height: pixel height of logo image. Valid if logo_on = 1
+ samsung,logo-addr: Address of logo image. Valid if logo_on = 1
+ samsung,rgb-mode: 0(MODE_RGB_P), 1(MODE_BGR_P),
+ 2(MODE_RGB_S), 3(MODE_BGR_S)
+ samsung,pclk-name: parent clock identifier: 1(MPLL), 2(EPLL), 3(VPLL)
+ samsung,sclk-div: parent_clock/source_clock ratio
+ samsung,dual-lcd-enabled: 1 if you support two LCD, else 0
+
+Example:
+SOC specific part:
+ fimd@14400000 {
+ compatible = "samsung,exynos-fimd";
+ reg = <0x14400000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+Board specific part:
+ fimd@14400000 {
+ samsung,vl-freq = <60>;
+ samsung,vl-col = <2560>;
+ samsung,vl-row = <1600>;
+ samsung,vl-width = <2560>;
+ samsung,vl-height = <1600>;
+
+ samsung,vl-clkp;
+ samsung,vl-dp;
+ samsung,vl-bpix = <4>;
+
+ samsung,vl-hspw = <32>;
+ samsung,vl-hbpd = <80>;
+ samsung,vl-hfpd = <48>;
+ samsung,vl-vspw = <6>;
+ samsung,vl-vbpd = <37>;
+ samsung,vl-vfpd = <3>;
+ samsung,vl-cmd-allow-len = <0xf>;
+
+ samsung,winid = <3>;
+ samsung,interface-mode = <1>;
+ samsung,dp-enabled = <1>;
+ samsung,dual-lcd-enabled = <0>;
+ };