TI: OMAP3: Remove SZ_xx references

This patch removes dependency on the sizes.h header file
and removes all references to SZ_xx.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
diff --git a/cpu/arm_cortexa8/omap3/mem.c b/cpu/arm_cortexa8/omap3/mem.c
index 079c848..b4dec39 100644
--- a/cpu/arm_cortexa8/omap3/mem.c
+++ b/cpu/arm_cortexa8/omap3/mem.c
@@ -92,7 +92,7 @@
 	u32 size, a_add_low, a_add_high;
 
 	size = get_sdr_cs_size(CS0);
-	size /= SZ_32M;			/* find size to offset CS1 */
+	size >>= 25;	/* divide by 32 MiB to find size to offset CS1 */
 	a_add_high = (size & 3) << 8;	/* set up low field */
 	a_add_low = (size & 0x3C) >> 2;	/* set up high field */
 	writel((a_add_high | a_add_low), &sdrc_base->cs_cfg);
@@ -249,7 +249,7 @@
 	enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
 #if defined(CONFIG_ENV_IS_IN_NAND)
 	f_off = SMNAND_ENV_OFFSET;
-	f_sec = SZ_128K;
+	f_sec = (128 << 10);	/* 128 KiB */
 	/* env setup */
 	boot_flash_base = base;
 	boot_flash_off = f_off;
@@ -265,7 +265,7 @@
 	enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
 #if defined(CONFIG_ENV_IS_IN_ONENAND)
 	f_off = ONENAND_ENV_OFFSET;
-	f_sec = SZ_128K;
+	f_sec = (128 << 10);	/* 128 KiB */
 	/* env setup */
 	boot_flash_base = base;
 	boot_flash_off = f_off;
diff --git a/cpu/arm_cortexa8/omap3/sys_info.c b/cpu/arm_cortexa8/omap3/sys_info.c
index 765aaf2..31b2003 100644
--- a/cpu/arm_cortexa8/omap3/sys_info.c
+++ b/cpu/arm_cortexa8/omap3/sys_info.c
@@ -124,7 +124,7 @@
 	/* get ram size field */
 	size = readl(&sdrc_base->cs[cs].mcfg) >> 8;
 	size &= 0x3FF;		/* remove unwanted bits */
-	size *= SZ_2M;		/* find size in MB */
+	size <<= 21;		/* multiply by 2 MiB to find size in MB */
 	return size;
 }
 
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index a8ac786..bd5037e 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -30,7 +30,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /* High Level Configuration Options */
 #define CONFIG_ARMCORTEXA8	1	/* This is an ARM V7 CPU core */
@@ -59,9 +58,9 @@
 #define CONFIG_REVISION_TAG		1
 
 /* Size of malloc() pool */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 
@@ -271,16 +270,16 @@
 #define CONFIG_SYS_HZ			1000
 
 /* The stack sizes are set up in start.S using the settings below */
-#define CONFIG_STACKSIZE		SZ_128K	/* regular stack */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ		SZ_4K	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ		SZ_4K	/* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ		(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ		(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*  Physical Memory Map  */
 #define CONFIG_NR_DRAM_BANKS		2 /* CS1 may or may not be populated */
 #define PHYS_SDRAM_1			OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE		SZ_128M	/* at least 128 meg */
+#define PHYS_SDRAM_1_SIZE		(128 << 20)	/* at least 128 MiB */
 #define PHYS_SDRAM_2			OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -289,7 +288,7 @@
 /* NAND and environment organization  */
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_ENV_IS_IN_NAND		1
 #define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 18dd3bc..19a5ec9 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -27,7 +27,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /*
  * High Level Configuration Options
@@ -62,9 +61,9 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 
@@ -250,10 +249,10 @@
  *
  * The stack sizes are set up in start.S using the settings below
  */
-#define CONFIG_STACKSIZE	SZ_128K	/* regular stack */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	SZ_4K	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	SZ_4K	/* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -261,7 +260,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	SZ_32M	/* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -280,7 +279,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
 						/* one chip */
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
 
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 72e9626..a5514ae 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -32,7 +32,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /*
  * High Level Configuration Options
@@ -67,9 +66,9 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 /*
@@ -231,10 +230,10 @@
  *
  * The stack sizes are set up in start.S using the settings below
  */
-#define CONFIG_STACKSIZE	SZ_128K	/* regular stack */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	SZ_4K	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	SZ_4K	/* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -242,7 +241,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	SZ_32M	/* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -261,7 +260,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors */
 						/* on one chip */
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
 
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 8554c01..ffb515d 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -19,7 +19,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /*
  * High Level Configuration Options
@@ -54,9 +53,9 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 
@@ -235,10 +234,10 @@
  *
  * The stack sizes are set up in start.S using the settings below
  */
-#define CONFIG_STACKSIZE	SZ_128K	/* regular stack */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	SZ_4K	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	SZ_4K	/* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -246,7 +245,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	SZ_32M	/* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -265,7 +264,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
 						/* one chip */
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
 
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index 064c0bc..6f21af3 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -22,7 +22,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /*
  * High Level Configuration Options
@@ -57,9 +56,9 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 
@@ -228,10 +227,10 @@
  *
  * The stack sizes are set up in start.S using the settings below
  */
-#define CONFIG_STACKSIZE	SZ_128K	/* regular stack */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	SZ_4K	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	SZ_4K	/* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -239,7 +238,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	SZ_32M	/* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -258,7 +257,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
 						/* one chip */
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
 
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index b55b8f0..da4b677 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -28,7 +28,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /*
  * High Level Configuration Options
@@ -63,9 +62,9 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 
@@ -236,10 +235,10 @@
  *
  * The stack sizes are set up in start.S using the settings below
  */
-#define CONFIG_STACKSIZE	SZ_128K	/* regular stack */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	SZ_4K	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	SZ_4K	/* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -247,7 +246,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	SZ_32M	/* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -266,7 +265,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
 						/* one chip */
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
 
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
index 75ab980..32cd6fd 100644
--- a/include/configs/omap3_zoom2.h
+++ b/include/configs/omap3_zoom2.h
@@ -29,7 +29,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /*
  * High Level Configuration Options
@@ -64,9 +63,9 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE			SZ_128K	/* Total Size Environment */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
 /*
@@ -201,10 +200,10 @@
  *
  * The stack sizes are set up in start.S using these settings
  */
-#define CONFIG_STACKSIZE	SZ_128K
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
 #ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	SZ_4K
-#define CONFIG_STACKSIZE_FIQ	SZ_4K
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -212,7 +211,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	SZ_32M	/* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /* SDRAM Bank Allocation method */
@@ -231,7 +230,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
 						/* one chip */
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN		SZ_256K	/* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base