Nios II - Add Altera EP1C20, EP1S10 and EP1S40 boards
Patch by Scott McNutt, 08 Jun 2006
diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h
new file mode 100644
index 0000000..5507f35
--- /dev/null
+++ b/include/configs/EP1C20.h
@@ -0,0 +1,199 @@
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*------------------------------------------------------------------------
+ * BOARD/CPU
+ *----------------------------------------------------------------------*/
+#define CONFIG_EP1C20 1 /* EP1C20 board */
+#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
+
+#define CFG_RESET_ADDR 0x00000000 /* Hard-reset address */
+#define CFG_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
+#define CFG_NIOS_SYSID_BASE 0x021208b8 /* System id address */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
+
+/*------------------------------------------------------------------------
+ * CACHE -- the following will support II/s and II/f. The II/s does not
+ * have dcache, so the cache instructions will behave as NOPs.
+ *----------------------------------------------------------------------*/
+#define CFG_ICACHE_SIZE 4096 /* 4 KByte total */
+#define CFG_ICACHELINE_SIZE 32 /* 32 bytes/line */
+#define CFG_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
+#define CFG_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
+
+/*------------------------------------------------------------------------
+ * MEMORY BASE ADDRESSES
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_BASE 0x00000000 /* FLASH base addr */
+#define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */
+#define CFG_SDRAM_BASE 0x01000000 /* SDRAM base addr */
+#define CFG_SDRAM_SIZE 0x01000000 /* 16 MByte */
+#define CFG_SRAM_BASE 0x02000000 /* SRAM base addr */
+#define CFG_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/
+
+/*------------------------------------------------------------------------
+ * MEMORY ORGANIZATION
+ * -Monitor at top.
+ * -The heap is placed below the monitor.
+ * -Global data is placed below the heap.
+ * -The stack is placed below global data (&grows down).
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 128k */
+#define CFG_GBL_DATA_SIZE 128 /* Global data size rsvd*/
+#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
+
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_OFFSET (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP CFG_GBL_DATA_OFFSET
+
+/*------------------------------------------------------------------------
+ * FLASH (AM29LV065D)
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_FLASH_SECT 128 /* Max # sects per bank */
+#define CFG_MAX_FLASH_BANKS 1 /* Max # of flash banks */
+#define CFG_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
+#define CFG_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
+#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size */
+
+/*------------------------------------------------------------------------
+ * ENVIRONMENT -- Put environment in sector CFG_MONITOR_LEN above
+ * CFG_RESET_ADDR, since we assume the monitor is stored at the
+ * reset address, no? This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH 1 /* Environment in flash */
+#define CFG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
+#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
+#define CFG_ENV_ADDR (CFG_RESET_ADDR + CFG_MONITOR_LEN)
+
+/*------------------------------------------------------------------------
+ * CONSOLE
+ *----------------------------------------------------------------------*/
+#if defined(CONFIG_CONSOLE_JTAG)
+#define CFG_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
+#else
+#define CFG_NIOS_CONSOLE 0x02120840 /* UART base addr */
+#endif
+
+#define CFG_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
+#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
+#define CFG_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
+
+/*------------------------------------------------------------------------
+ * EPCS Device -- wne CFG_NIOS_EPCSBASE is defined code/commands for
+ * epcs device access is enabled. The base address is the epcs
+ * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
+ * The register base is currently at offset 0x600 from the memory base.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_EPCSBASE 0x02100200 /* EPCS register base */
+
+/*------------------------------------------------------------------------
+ * DEBUG
+ *----------------------------------------------------------------------*/
+#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
+
+/*------------------------------------------------------------------------
+ * TIMEBASE --
+ *
+ * The high res timer defaults to 1 msec. Since it includes the period
+ * registers, we can slow it down to 10 msec using TMRCNT. If the default
+ * period is acceptable, TMRCNT can be left undefined.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
+#define CFG_NIOS_TMRIRQ 3 /* Timer IRQ num */
+#define CFG_NIOS_TMRMS 10 /* 10 msec per tick */
+#define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
+#define CFG_HZ (CONFIG_SYS_CLK_FREQ/(CFG_NIOS_TMRCNT + 1))
+
+/*------------------------------------------------------------------------
+ * STATUS LED -- Provides a simple blinking led. For Nios2 each board
+ * must implement its own led routines -- leds are, after all,
+ * board-specific, no?
+ *----------------------------------------------------------------------*/
+#define CFG_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
+#define CONFIG_STATUS_LED /* Enable status driver */
+
+#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
+#define STATUS_LED_STATE 1 /* Blinking */
+#define STATUS_LED_PERIOD (500/CFG_NIOS_TMRMS) /* Every 500 msec */
+
+/*------------------------------------------------------------------------
+ * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
+ * and really doesn't need any additional clutter. So I choose the lazy
+ * way out to avoid changes there -- define the base address to ensure
+ * cache bypass so there's no need to monkey with inx/outx macros.
+ *----------------------------------------------------------------------*/
+#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
+#define CONFIG_DRIVER_SMC91111 /* Using SMC91c111 */
+#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
+#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
+
+#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_IPADDR 192.168.2.21
+#define CONFIG_SERVERIP 192.168.2.16
+
+/*------------------------------------------------------------------------
+ * COMMANDS
+ *----------------------------------------------------------------------*/
+#define CONFIG_COMMANDS (CFG_CMD_BDI | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_ECHO | \
+ CFG_CMD_ENV | \
+ CFG_CMD_FLASH | \
+ CFG_CMD_IMI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_LOADS | \
+ CFG_CMD_LOADB | \
+ CFG_CMD_MEMORY | \
+ CFG_CMD_MISC | \
+ CFG_CMD_NET | \
+ CFG_CMD_PING | \
+ CFG_CMD_RUN | \
+ CFG_CMD_SAVES )
+#include <cmd_confdefs.h>
+
+/*------------------------------------------------------------------------
+ * MISC
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP /* Provide extended help*/
+#define CFG_PROMPT "==> " /* Command prompt */
+#define CFG_CBSIZE 256 /* Console I/O buf size */
+#define CFG_MAXARGS 16 /* Max command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot arg buf size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buf size */
+#define CFG_LOAD_ADDR CFG_SDRAM_BASE /* Default load address */
+#define CFG_MEMTEST_START CFG_SDRAM_BASE /* Start addr for test */
+#define CFG_MEMTEST_END CFG_INIT_SP - 0x00020000
+
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+#endif /* __CONFIG_H */