Merge branch 'master' of git://git.denx.de/u-boot-arm
diff --git a/board/davinci/common/psc.c b/board/davinci/common/psc.c
index d538d51..28e2a4b 100644
--- a/board/davinci/common/psc.c
+++ b/board/davinci/common/psc.c
@@ -26,6 +26,14 @@
#include <common.h>
#include <asm/arch/hardware.h>
+#define PINMUX0_EMACEN (1 << 31)
+#define PINMUX0_AECS5 (1 << 11)
+#define PINMUX0_AECS4 (1 << 10)
+
+#define PINMUX1_I2C (1 << 7)
+#define PINMUX1_UART1 (1 << 1)
+#define PINMUX1_UART0 (1 << 0)
+
/*
* The DM6446 includes two separate power domains: "Always On" and "DSP". The
* "Always On" power domain is always on when the chip is on. The "Always On"
@@ -115,3 +123,60 @@
REG(PSC_GBLCTL) &= ~0x1f;
}
#endif /* CONFIG_SYS_USE_DSPLINK */
+
+void davinci_enable_uart0(void)
+{
+ lpsc_on(DAVINCI_LPSC_UART0);
+
+ /* Bringup UART0 out of reset */
+ REG(UART0_PWREMU_MGMT) = 0x0000e003;
+
+ /* Enable UART0 MUX lines */
+ REG(PINMUX1) |= PINMUX1_UART0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+void davinci_enable_emac(void)
+{
+ lpsc_on(DAVINCI_LPSC_EMAC);
+ lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
+ lpsc_on(DAVINCI_LPSC_MDIO);
+
+ /* Enable GIO3.3V cells used for EMAC */
+ REG(VDD3P3V_PWDN) = 0;
+
+ /* Enable EMAC. */
+ REG(PINMUX0) |= PINMUX0_EMACEN;
+}
+#endif
+
+void davinci_enable_i2c(void)
+{
+ lpsc_on(DAVINCI_LPSC_I2C);
+
+ /* Enable I2C pin Mux */
+ REG(PINMUX1) |= PINMUX1_I2C;
+}
+
+void davinci_errata_workarounds(void)
+{
+ /*
+ * Workaround for TMS320DM6446 errata 1.3.22:
+ * PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
+ * Revision(s) Affected: 1.3 and earlier
+ */
+ REG(PSC_SILVER_BULLET) = 0;
+
+ /*
+ * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
+ * as suggested in TMS320DM6446 errata 2.1.2:
+ *
+ * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
+ * low priority modules can occupy the bus and prevent high priority
+ * modules like the VPSS from getting the required DDR2 throughput.
+ * A hex value of 0x20 should provide a good ARM (cache enabled)
+ * performance and still allow good utilization by the VPSS or other
+ * modules.
+ */
+ REG(VBPR) = 0x20;
+}
diff --git a/board/davinci/common/psc.h b/board/davinci/common/psc.h
index 6ab2575..b2dd7b5 100644
--- a/board/davinci/common/psc.h
+++ b/board/davinci/common/psc.h
@@ -24,5 +24,9 @@
void lpsc_on(unsigned int id);
void dsp_on(void);
+void davinci_enable_uart0(void);
+void davinci_enable_emac(void);
+void davinci_enable_i2c(void);
+void davinci_errata_workarounds(void);
#endif /* __PSC_H */
diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c
index 3fe8858..22308de 100644
--- a/board/davinci/dvevm/dvevm.c
+++ b/board/davinci/dvevm/dvevm.c
@@ -27,7 +27,6 @@
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@@ -41,16 +40,13 @@
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
- /* Workaround for TMS320DM6446 errata 1.3.22 */
- REG(PSC_SILVER_BULLET) = 0;
+ /* Configure AEMIF pins (although this should be configured at boot time
+ * with pull-up/pull-down resistors) */
+ REG(PINMUX0) = 0x00000c1f;
+
+ davinci_errata_workarounds();
/* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
- lpsc_on(DAVINCI_LPSC_I2C);
- lpsc_on(DAVINCI_LPSC_UART0);
- lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
lpsc_on(DAVINCI_LPSC_USB);
@@ -59,24 +55,11 @@
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x0000e003;
+ davinci_enable_uart0();
+ davinci_enable_emac();
+ davinci_enable_i2c();
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= 1;
-
- /* Enable EMAC and AEMIF pins */
- REG(PINMUX0) = 0x80000c1f;
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= (1 << 7);
-
- /* Set the Bus Priority Register to appropriate value */
- REG(VBPR) = 0x20;
-
+ lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
diff --git a/board/davinci/schmoogie/schmoogie.c b/board/davinci/schmoogie/schmoogie.c
index 3504a2e..433769a 100644
--- a/board/davinci/schmoogie/schmoogie.c
+++ b/board/davinci/schmoogie/schmoogie.c
@@ -27,7 +27,6 @@
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@@ -41,16 +40,13 @@
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
- /* Workaround for TMS320DM6446 errata 1.3.22 */
- REG(PSC_SILVER_BULLET) = 0;
+ /* Configure AEMIF pins (although this should be configured at boot time
+ * with pull-up/pull-down resistors) */
+ REG(PINMUX0) = 0x00000c1f;
+
+ davinci_errata_workarounds();
/* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
- lpsc_on(DAVINCI_LPSC_I2C);
- lpsc_on(DAVINCI_LPSC_UART0);
- lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
#if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -58,24 +54,11 @@
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x0000e003;
+ davinci_enable_uart0();
+ davinci_enable_emac();
+ davinci_enable_i2c();
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= 1;
-
- /* Enable EMAC and AEMIF pins */
- REG(PINMUX0) = 0x80000c1f;
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= (1 << 7);
-
- /* Set the Bus Priority Register to appropriate value */
- REG(VBPR) = 0x20;
-
+ lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
@@ -87,7 +70,7 @@
int i = 0;
/* Set serial number from UID chip */
- u_int8_t crc_tbl[256] = {
+ const u_int8_t crc_tbl[256] = {
0x00, 0x5e, 0xbc, 0xe2, 0x61, 0x3f, 0xdd, 0x83,
0xc2, 0x9c, 0x7e, 0x20, 0xa3, 0xfd, 0x1f, 0x41,
0x9d, 0xc3, 0x21, 0x7f, 0xfc, 0xa2, 0x40, 0x1e,
diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c
index 9296d7b..e76f86d 100644
--- a/board/davinci/sffsdr/sffsdr.c
+++ b/board/davinci/sffsdr/sffsdr.c
@@ -30,7 +30,6 @@
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@@ -51,16 +50,9 @@
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
- /* Workaround for TMS320DM6446 errata 1.3.22 */
- REG(PSC_SILVER_BULLET) = 0;
+ davinci_errata_workarounds();
/* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
- lpsc_on(DAVINCI_LPSC_I2C);
- lpsc_on(DAVINCI_LPSC_UART0);
- lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
#if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -68,24 +60,11 @@
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x0000e003;
+ davinci_enable_uart0();
+ davinci_enable_emac();
+ davinci_enable_i2c();
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= 1;
-
- /* Enable EMAC and AEMIF pins */
- REG(PINMUX0) = 0x80000c1f;
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= (1 << 7);
-
- /* Set the Bus Priority Register to appropriate value */
- REG(VBPR) = 0x20;
-
+ lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
diff --git a/board/davinci/sonata/sonata.c b/board/davinci/sonata/sonata.c
index 6de9356..d56b443 100644
--- a/board/davinci/sonata/sonata.c
+++ b/board/davinci/sonata/sonata.c
@@ -26,7 +26,6 @@
#include <common.h>
#include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@@ -40,16 +39,13 @@
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
- /* Workaround for TMS320DM6446 errata 1.3.22 */
- REG(PSC_SILVER_BULLET) = 0;
+ /* Configure AEMIF pins (although this should be configured at boot time
+ * with pull-up/pull-down resistors) */
+ REG(PINMUX0) = 0x00000c1f;
+
+ davinci_errata_workarounds();
/* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_EMAC);
- lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
- lpsc_on(DAVINCI_LPSC_MDIO);
- lpsc_on(DAVINCI_LPSC_I2C);
- lpsc_on(DAVINCI_LPSC_UART0);
- lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
#if !defined(CONFIG_SYS_USE_DSPLINK)
@@ -57,24 +53,11 @@
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
- /* Bringup UART0 out of reset */
- REG(UART0_PWREMU_MGMT) = 0x0000e003;
+ davinci_enable_uart0();
+ davinci_enable_emac();
+ davinci_enable_i2c();
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0;
-
- /* Enable UART0 MUX lines */
- REG(PINMUX1) |= 1;
-
- /* Enable EMAC and AEMIF pins */
- REG(PINMUX0) = 0x80000c1f;
-
- /* Enable I2C pin Mux */
- REG(PINMUX1) |= (1 << 7);
-
- /* Set the Bus Priority Register to appropriate value */
- REG(VBPR) = 0x20;
-
+ lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
diff --git a/board/omap3/beagle/beagle.c b/board/omap3/beagle/beagle.c
index ecdea09..7377058 100644
--- a/board/omap3/beagle/beagle.c
+++ b/board/omap3/beagle/beagle.c
@@ -36,6 +36,8 @@
#include <asm/mach-types.h>
#include "beagle.h"
+static int beagle_revision_c;
+
/******************************************************************************
* Routine: board_init
* Description: Early hardware init.
@@ -54,6 +56,43 @@
}
/******************************************************************************
+ * Routine: beagle_get_revision
+ * Description: Return revision of the BeagleBoard this code is running on.
+ * If it is a revision Ax/Bx board, this function returns 0,
+ * on a revision C board you will get a 1.
+ *****************************************************************************/
+int beagle_get_revision(void)
+{
+ return beagle_revision_c;
+}
+
+/******************************************************************************
+ * Routine: beagle_identify
+ * Description: Detect if we are running on a Beagle revision Ax/Bx or
+ * Cx. This can be done by GPIO_171. If this is low, we are
+ * running on a revision C board.
+ *****************************************************************************/
+void beagle_identify(void)
+{
+ gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+ /* Configure GPIO 171 as input */
+ writel(readl(&gpio6_base->oe) | GPIO11, &gpio6_base->oe);
+
+ /* Get value of GPIO 171 */
+ beagle_revision_c = readl(&gpio6_base->datain) & BOARD_REVISION_MASK;
+
+ printf("Board revision ");
+ if (beagle_revision_c) {
+ printf("Ax/Bx\n");
+ beagle_revision_c = 0;
+ } else {
+ printf("C\n");
+ beagle_revision_c = 1;
+ }
+}
+
+/******************************************************************************
* Routine: misc_init_r
* Description: Configure board specific parts
*****************************************************************************/
@@ -75,6 +114,8 @@
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
+ beagle_identify();
+
return 0;
}
diff --git a/board/omap3/beagle/beagle.h b/board/omap3/beagle/beagle.h
index 6511ffa..d66f159 100644
--- a/board/omap3/beagle/beagle.h
+++ b/board/omap3/beagle/beagle.h
@@ -27,7 +27,6 @@
SDP_3430_V1,
SDP_3430_V2,
DDR_STACKED,
- "3530",
"OMAP3 Beagle board",
#if defined(CONFIG_ENV_IS_IN_ONENAND)
"OneNAND",
@@ -36,6 +35,8 @@
#endif
};
+#define BOARD_REVISION_MASK (0x1 << 11)
+
/*
* IEN - Input Enable
* IDIS - Input Disable
diff --git a/board/omap3/evm/evm.h b/board/omap3/evm/evm.h
index 4ecea7f..199824f 100644
--- a/board/omap3/evm/evm.h
+++ b/board/omap3/evm/evm.h
@@ -27,7 +27,6 @@
OMAP3EVM_V1,
OMAP3EVM_V2,
DDR_DISCRETE,
- "35X-Family",
"OMAP3 EVM board",
#if defined(CONFIG_ENV_IS_IN_ONENAND)
"OneNAND",
diff --git a/board/omap3/overo/Makefile b/board/omap3/overo/Makefile
index c165629..dd673ca 100644
--- a/board/omap3/overo/Makefile
+++ b/board/omap3/overo/Makefile
@@ -44,4 +44,5 @@
# defines $(obj).depend target
include $(SRCTREE)/rules.mk
+#########################################################################
sinclude $(obj).depend
diff --git a/board/omap3/overo/overo.c b/board/omap3/overo/overo.c
index 7964123..48375ad 100644
--- a/board/omap3/overo/overo.c
+++ b/board/omap3/overo/overo.c
@@ -58,21 +58,8 @@
*****************************************************************************/
int misc_init_r(void)
{
- gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
- gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
-
power_init_r();
- /* Configure GPIOs to output */
- writel(~((GPIO10) | GPIO9 | GPIO3 | GPIO2), &gpio6_base->oe);
- writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
-
- /* Set GPIOs */
- writel(GPIO10 | GPIO9 | GPIO3 | GPIO2, &gpio6_base->setdataout);
- writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
-
return 0;
}
diff --git a/board/omap3/overo/overo.h b/board/omap3/overo/overo.h
index 3c1b6bc..71de3f1 100644
--- a/board/omap3/overo/overo.h
+++ b/board/omap3/overo/overo.h
@@ -27,7 +27,6 @@
SDP_3430_V1,
SDP_3430_V2,
DDR_STACKED,
- "3503",
"Gumstix Overo board",
#if defined(CONFIG_ENV_IS_IN_ONENAND)
"OneNAND",
@@ -130,7 +129,8 @@
MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
- MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | DIS | M4)) /*GPIO_64*/\
+ /* - SMSC911X_NRES*/\
MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_nCS3*/\
/*DSS*/\
MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
@@ -184,7 +184,7 @@
MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | EN | M4)) /*GPIO_114*/\
MUX_VAL(CP(CSI2_DY1), (IEN | PTU | EN | M4)) /*GPIO_115*/\
/*Audio Interface */\
MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
@@ -218,10 +218,10 @@
MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M1)) /*UART2_RX*/\
- MUX_VAL(CP(UART2_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
- MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_145*/\
- MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M4)) /*GPIO_146*/\
- MUX_VAL(CP(UART2_RX), (IDIS | PTD | DIS | M4)) /*GPIO_147*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
+ MUX_VAL(CP(UART2_RTS), (IEN | PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX), (IEN | PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M4)) /*GPIO_147*/\
MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
MUX_VAL(CP(UART1_RTS), (IEN | PTU | DIS | M4)) /*GPIO_149*/ \
MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M4)) /*GPIO_150-MMC3_WP*/\
@@ -271,7 +271,8 @@
MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI */\
MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
- MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTD | DIS | M4)) /*GPIO_176*/\
+ /* - SMSC911X_IRQ*/\
MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA2*/\
MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA7*/\
MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA4*/\
@@ -306,7 +307,7 @@
MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT6*/\
MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT5*/\
MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
- MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | EN | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DIR*/\
MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_NXT*/\
MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA0*/\
diff --git a/board/omap3/pandora/pandora.h b/board/omap3/pandora/pandora.h
index 8525a03..dd09f12 100644
--- a/board/omap3/pandora/pandora.h
+++ b/board/omap3/pandora/pandora.h
@@ -27,7 +27,6 @@
SDP_3430_V1,
SDP_3430_V2,
DDR_STACKED,
- "3530",
"OMAP3 Pandora",
"NAND",
};
@@ -200,12 +199,12 @@
MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M1)) /*MMC2_CLKIN*/\
MUX_VAL(CP(MMC1_DAT5), (IEN | PTD | DIS | M4)) /*GPIO_127 - MMC2_WP*/\
/*SDIO Interface to WIFI Module*/\
- MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M2)) /*MMC3_CLK*/\
- MUX_VAL(CP(ETK_CTL_ES2), (IEN | PTD | DIS | M2)) /*MMC3_CMD*/\
- MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT0*/\
- MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT1*/\
- MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT2*/\
- MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | DIS | M2)) /*MMC3_DAT3*/\
+ MUX_VAL(CP(ETK_CLK_ES2), (IEN | PTD | DIS | M2)) /*MMC3_CLK*/\
+ MUX_VAL(CP(ETK_CTL_ES2), (IEN | PTU | EN | M2)) /*MMC3_CMD*/\
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT0*/\
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT1*/\
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT2*/\
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT3*/\
/*Audio Interface To Bluetooth chip*/\
MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) /*McBSP3_DX*/\
MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) /*McBSP3_DR*/\
diff --git a/board/omap3/zoom1/zoom1.h b/board/omap3/zoom1/zoom1.h
index d389492..bc8fba8 100644
--- a/board/omap3/zoom1/zoom1.h
+++ b/board/omap3/zoom1/zoom1.h
@@ -31,7 +31,6 @@
SDP_3430_V1,
SDP_3430_V2,
DDR_STACKED,
- "3430",
"OMAP3 Zoom MDK Rev 1",
"NAND",
};
diff --git a/board/st/nmdk8815/nmdk8815.c b/board/st/nmdk8815/nmdk8815.c
index c54eac1..edf4626 100644
--- a/board/st/nmdk8815/nmdk8815.c
+++ b/board/st/nmdk8815/nmdk8815.c
@@ -49,8 +49,11 @@
writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);
- icache_enable();
+ /* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
+ writel(0x0000305b, REG_FSMC_BCR1);
+ writel(0x00033f33, REG_FSMC_BTR1);
+ icache_enable();
return 0;
}
diff --git a/common/devices.c b/common/devices.c
index 38f1bbc..ba53c9b 100644
--- a/common/devices.c
+++ b/common/devices.c
@@ -215,6 +215,9 @@
/* Initialize the list */
INIT_LIST_HEAD(&(devs.list));
+#ifdef CONFIG_ARM_DCC_MULTI
+ drv_arm_dcc_init ();
+#endif
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
diff --git a/cpu/arm_cortexa8/omap3/sys_info.c b/cpu/arm_cortexa8/omap3/sys_info.c
index ab012b6..28a1020 100644
--- a/cpu/arm_cortexa8/omap3/sys_info.c
+++ b/cpu/arm_cortexa8/omap3/sys_info.c
@@ -37,6 +37,14 @@
static ctrl_t *ctrl_base = (ctrl_t *)OMAP34XX_CTRL_BASE;
/******************************************
+ * get_cpu_type(void) - extract cpu info
+ ******************************************/
+u32 get_cpu_type(void)
+{
+ return readl(&ctrl_base->ctrl_omap_stat);
+}
+
+/******************************************
* get_cpu_rev(void) - extract version info
******************************************/
u32 get_cpu_rev(void)
@@ -156,7 +164,25 @@
*********************************************************************/
void display_board_info(u32 btype)
{
- char *mem_s, *sec_s;
+ char *cpu_s, *mem_s, *sec_s;
+
+ switch (get_cpu_type()) {
+ case OMAP3503:
+ cpu_s = "3503";
+ break;
+ case OMAP3515:
+ cpu_s = "3515";
+ break;
+ case OMAP3525:
+ cpu_s = "3525";
+ break;
+ case OMAP3530:
+ cpu_s = "3530";
+ break;
+ default:
+ cpu_s = "35XX";
+ break;
+ }
if (is_mem_sdr())
mem_s = "mSDR";
@@ -180,7 +206,8 @@
sec_s = "?";
}
- printf("OMAP%s-%s rev %d, CPU-OPP2 L3-165MHz\n", sysinfo.cpu_string,
+
+ printf("OMAP%s-%s rev %d, CPU-OPP2 L3-165MHz\n", cpu_s,
sec_s, get_cpu_rev());
printf("%s + %s/%s\n", sysinfo.board_string,
mem_s, sysinfo.nand_string);
diff --git a/drivers/mmc/omap3_mmc.c b/drivers/mmc/omap3_mmc.c
index 399c57b..e90db7e 100644
--- a/drivers/mmc/omap3_mmc.c
+++ b/drivers/mmc/omap3_mmc.c
@@ -28,6 +28,7 @@
#include <mmc.h>
#include <part.h>
#include <i2c.h>
+#include <asm/io.h>
#include <asm/arch/mmc.h>
const unsigned short mmc_transspeed_val[15][4] = {
@@ -50,6 +51,7 @@
mmc_card_data cur_card_data;
static block_dev_desc_t mmc_blk_dev;
+static hsmmc_t *mmc_base = (hsmmc_t *)OMAP_HSMMC_BASE;
block_dev_desc_t *mmc_get_dev(int dev)
{
@@ -60,55 +62,49 @@
{
unsigned char data;
- data = 0x20;
- i2c_write(0x4B, 0x82, 1, &data, 1);
- data = 0x2;
- i2c_write(0x4B, 0x85, 1, &data, 1);
+ data = DEV_GRP_P1;
+ i2c_write(PWRMGT_ADDR_ID4, VMMC1_DEV_GRP, 1, &data, 1);
+ data = VMMC1_VSEL_30;
+ i2c_write(PWRMGT_ADDR_ID4, VMMC1_DEDICATED, 1, &data, 1);
}
unsigned char mmc_board_init(void)
{
- unsigned int value = 0;
+ t2_t *t2_base = (t2_t *)T2_BASE;
twl4030_mmc_config();
- value = CONTROL_PBIAS_LITE;
- CONTROL_PBIAS_LITE = value | (1 << 2) | (1 << 1) | (1 << 9);
+ writel(readl(&t2_base->pbias_lite) | PBIASLITEPWRDNZ1 |
+ PBIASSPEEDCTRL0 | PBIASLITEPWRDNZ0,
+ &t2_base->pbias_lite);
- value = CONTROL_DEV_CONF0;
- CONTROL_DEV_CONF0 = value | (1 << 24);
+ writel(readl(&t2_base->devconf0) | MMCSDIO1ADPCLKISEL,
+ &t2_base->devconf0);
return 1;
}
void mmc_init_stream(void)
{
- volatile unsigned int mmc_stat;
+ writel(readl(&mmc_base->con) | INIT_INITSTREAM, &mmc_base->con);
- OMAP_HSMMC_CON |= INIT_INITSTREAM;
+ writel(MMC_CMD0, &mmc_base->cmd);
+ while (!(readl(&mmc_base->stat) & CC_MASK));
- OMAP_HSMMC_CMD = MMC_CMD0;
- do {
- mmc_stat = OMAP_HSMMC_STAT;
- } while (!(mmc_stat & CC_MASK));
+ writel(CC_MASK, &mmc_base->stat);
- OMAP_HSMMC_STAT = CC_MASK;
+ writel(MMC_CMD0, &mmc_base->cmd);
+ while (!(readl(&mmc_base->stat) & CC_MASK));
- OMAP_HSMMC_CMD = MMC_CMD0;
- do {
- mmc_stat = OMAP_HSMMC_STAT;
- } while (!(mmc_stat & CC_MASK));
-
- OMAP_HSMMC_STAT = OMAP_HSMMC_STAT;
- OMAP_HSMMC_CON &= ~INIT_INITSTREAM;
+ writel(readl(&mmc_base->con) & ~INIT_INITSTREAM, &mmc_base->con);
}
unsigned char mmc_clock_config(unsigned int iclk, unsigned short clk_div)
{
unsigned int val;
- mmc_reg_out(OMAP_HSMMC_SYSCTL, (ICE_MASK | DTO_MASK | CEN_MASK),
- (ICE_STOP | DTO_15THDTO | CEN_DISABLE));
+ mmc_reg_out(&mmc_base->sysctl, (ICE_MASK | DTO_MASK | CEN_MASK),
+ (ICE_STOP | DTO_15THDTO | CEN_DISABLE));
switch (iclk) {
case CLK_INITSEQ:
@@ -123,12 +119,12 @@
default:
return 0;
}
- mmc_reg_out(OMAP_HSMMC_SYSCTL,
- ICE_MASK | CLKD_MASK, (val << CLKD_OFFSET) | ICE_OSCILLATE);
+ mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK,
+ (val << CLKD_OFFSET) | ICE_OSCILLATE);
- while ((OMAP_HSMMC_SYSCTL & ICS_MASK) == ICS_NOTREADY) ;
+ while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY);
- OMAP_HSMMC_SYSCTL |= CEN_ENABLE;
+ writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl);
return 1;
}
@@ -138,59 +134,63 @@
mmc_board_init();
- OMAP_HSMMC_SYSCONFIG |= MMC_SOFTRESET;
- while ((OMAP_HSMMC_SYSSTATUS & RESETDONE) == 0) ;
+ writel(readl(&mmc_base->sysconfig) | MMC_SOFTRESET,
+ &mmc_base->sysconfig);
+ while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0);
- OMAP_HSMMC_SYSCTL |= SOFTRESETALL;
- while ((OMAP_HSMMC_SYSCTL & SOFTRESETALL) != 0x0) ;
+ writel(readl(&mmc_base->sysctl) | SOFTRESETALL, &mmc_base->sysctl);
+ while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0);
- OMAP_HSMMC_HCTL = DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0;
- OMAP_HSMMC_CAPA |= VS30_3V0SUP | VS18_1V8SUP;
+ writel(DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0, &mmc_base->hctl);
+ writel(readl(&mmc_base->capa) | VS30_3V0SUP | VS18_1V8SUP,
+ &mmc_base->capa);
- reg_val = OMAP_HSMMC_CON & RESERVED_MASK;
+ reg_val = readl(&mmc_base->con) & RESERVED_MASK;
- OMAP_HSMMC_CON = CTPL_MMC_SD | reg_val | WPP_ACTIVEHIGH |
- CDP_ACTIVEHIGH | MIT_CTO | DW8_1_4BITMODE | MODE_FUNC |
- STR_BLOCK | HR_NOHOSTRESP | INIT_NOINIT | NOOPENDRAIN;
+ writel(CTPL_MMC_SD | reg_val | WPP_ACTIVEHIGH | CDP_ACTIVEHIGH |
+ MIT_CTO | DW8_1_4BITMODE | MODE_FUNC | STR_BLOCK |
+ HR_NOHOSTRESP | INIT_NOINIT | NOOPENDRAIN, &mmc_base->con);
mmc_clock_config(CLK_INITSEQ, 0);
- OMAP_HSMMC_HCTL |= SDBP_PWRON;
+ writel(readl(&mmc_base->hctl) | SDBP_PWRON, &mmc_base->hctl);
- OMAP_HSMMC_IE = 0x307f0033;
+ writel(IE_BADA | IE_CERR | IE_DEB | IE_DCRC | IE_DTO | IE_CIE |
+ IE_CEB | IE_CCRC | IE_CTO | IE_BRR | IE_BWR | IE_TC | IE_CC,
+ &mmc_base->ie);
mmc_init_stream();
return 1;
}
unsigned char mmc_send_cmd(unsigned int cmd, unsigned int arg,
- unsigned int *response)
+ unsigned int *response)
{
- volatile unsigned int mmc_stat;
+ unsigned int mmc_stat;
- while ((OMAP_HSMMC_PSTATE & DATI_MASK) == DATI_CMDDIS) ;
+ while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS);
- OMAP_HSMMC_BLK = BLEN_512BYTESLEN | NBLK_STPCNT;
- OMAP_HSMMC_STAT = 0xFFFFFFFF;
- OMAP_HSMMC_ARG = arg;
- OMAP_HSMMC_CMD = cmd | CMD_TYPE_NORMAL | CICE_NOCHECK |
- CCCE_NOCHECK | MSBS_SGLEBLK | ACEN_DISABLE | BCE_DISABLE |
- DE_DISABLE;
+ writel(BLEN_512BYTESLEN | NBLK_STPCNT, &mmc_base->blk);
+ writel(0xFFFFFFFF, &mmc_base->stat);
+ writel(arg, &mmc_base->arg);
+ writel(cmd | CMD_TYPE_NORMAL | CICE_NOCHECK | CCCE_NOCHECK |
+ MSBS_SGLEBLK | ACEN_DISABLE | BCE_DISABLE | DE_DISABLE,
+ &mmc_base->cmd);
while (1) {
do {
- mmc_stat = OMAP_HSMMC_STAT;
+ mmc_stat = readl(&mmc_base->stat);
} while (mmc_stat == 0);
if ((mmc_stat & ERRI_MASK) != 0)
return (unsigned char) mmc_stat;
if (mmc_stat & CC_MASK) {
- OMAP_HSMMC_STAT = CC_MASK;
- response[0] = OMAP_HSMMC_RSP10;
+ writel(CC_MASK, &mmc_base->stat);
+ response[0] = readl(&mmc_base->rsp10);
if ((cmd & RSP_TYPE_MASK) == RSP_TYPE_LGHT136) {
- response[1] = OMAP_HSMMC_RSP32;
- response[2] = OMAP_HSMMC_RSP54;
- response[3] = OMAP_HSMMC_RSP76;
+ response[1] = readl(&mmc_base->rsp32);
+ response[2] = readl(&mmc_base->rsp54);
+ response[3] = readl(&mmc_base->rsp76);
}
break;
}
@@ -200,7 +200,7 @@
unsigned char mmc_read_data(unsigned int *output_buf)
{
- volatile unsigned int mmc_stat;
+ unsigned int mmc_stat;
unsigned int read_count = 0;
/*
@@ -208,7 +208,7 @@
*/
while (1) {
do {
- mmc_stat = OMAP_HSMMC_STAT;
+ mmc_stat = readl(&mmc_base->stat);
} while (mmc_stat == 0);
if ((mmc_stat & ERRI_MASK) != 0)
@@ -217,19 +217,22 @@
if (mmc_stat & BRR_MASK) {
unsigned int k;
- OMAP_HSMMC_STAT |= BRR_MASK;
+ writel(readl(&mmc_base->stat) | BRR_MASK,
+ &mmc_base->stat);
for (k = 0; k < MMCSD_SECTOR_SIZE / 4; k++) {
- *output_buf = OMAP_HSMMC_DATA;
+ *output_buf = readl(&mmc_base->data);
output_buf++;
read_count += 4;
}
}
if (mmc_stat & BWR_MASK)
- OMAP_HSMMC_STAT |= BWR_MASK;
+ writel(readl(&mmc_base->stat) | BWR_MASK,
+ &mmc_base->stat);
if (mmc_stat & TC_MASK) {
- OMAP_HSMMC_STAT |= TC_MASK;
+ writel(readl(&mmc_base->stat) | TC_MASK,
+ &mmc_base->stat);
break;
}
}
@@ -273,8 +276,8 @@
mmc_card_cur->card_type = MMC_CARD;
ocr_value |= MMC_OCR_REG_ACCESS_MODE_SECTOR;
ret_cmd41 = MMC_CMD1;
- OMAP_HSMMC_CON &= ~OD;
- OMAP_HSMMC_CON |= OPENDRAIN;
+ writel(readl(&mmc_base->con) & ~OD, &mmc_base->con);
+ writel(readl(&mmc_base->con) | OPENDRAIN, &mmc_base->con);
}
argument = ocr_value;
@@ -342,8 +345,8 @@
mmc_card_cur->RCA = ((mmc_resp_r6 *) resp)->newpublishedrca;
}
- OMAP_HSMMC_CON &= ~OD;
- OMAP_HSMMC_CON |= NOOPENDRAIN;
+ writel(readl(&mmc_base->con) & ~OD, &mmc_base->con);
+ writel(readl(&mmc_base->con) | NOOPENDRAIN, &mmc_base->con);
return 1;
}
@@ -518,7 +521,7 @@
void *dst)
{
omap_mmc_read_sect(blknr, (blkcnt * MMCSD_SECTOR_SIZE), &cur_card_data,
- (unsigned long *) dst);
+ (unsigned long *) dst);
return 1;
}
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 24edb27..5974d77 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -38,6 +38,7 @@
COBJS-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
COBJS-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
+COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o
COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
endif
diff --git a/drivers/mtd/nand/nomadik.c b/drivers/mtd/nand/nomadik.c
new file mode 100644
index 0000000..b76f4cb
--- /dev/null
+++ b/drivers/mtd/nand/nomadik.c
@@ -0,0 +1,221 @@
+/*
+ * (C) Copyright 2007 STMicroelectronics, <www.st.com>
+ * (C) Copyright 2009 Alessandro Rubini <rubini@unipv.it>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <nand.h>
+#include <asm/io.h>
+
+static inline int parity(int b) /* b is really a byte; returns 0 or ~0 */
+{
+ __asm__ __volatile__(
+ "eor %0, %0, %0, lsr #4\n\t"
+ "eor %0, %0, %0, lsr #2\n\t"
+ "eor %0, %0, %0, lsr #1\n\t"
+ "ands %0, %0, #1\n\t"
+ "subne %0, %0, #2\t"
+ : "=r" (b) : "0" (b));
+ return b;
+}
+
+/*
+ * This is the ECC routine used in hardware, according to the manual.
+ * HW claims to make the calculation but not the correction; so we must
+ * recalculate the bytes for a comparison.
+ */
+static int ecc512(const unsigned char *data, unsigned char *ecc)
+{
+ int gpar = 0;
+ int i, val, par;
+ int pbits = 0; /* P8, P16, ... P2048 */
+ int pprime = 0; /* P8', P16', ... P2048' */
+ int lowbits; /* P1, P2, P4 and primes */
+
+ for (i = 0; i < 512; i++) {
+ par = parity((val = data[i]));
+ gpar ^= val;
+ pbits ^= (i & par);
+ }
+ /*
+ * Ok, now gpar is global parity (xor of all bytes)
+ * pbits are all the parity bits (non-prime ones)
+ */
+ par = parity(gpar);
+ pprime = pbits ^ par;
+ /* Put low bits in the right position for ecc[2] (bits 7..2) */
+ lowbits = 0
+ | (parity(gpar & 0xf0) & 0x80) /* P4 */
+ | (parity(gpar & 0x0f) & 0x40) /* P4' */
+ | (parity(gpar & 0xcc) & 0x20) /* P2 */
+ | (parity(gpar & 0x33) & 0x10) /* P2' */
+ | (parity(gpar & 0xaa) & 0x08) /* P1 */
+ | (parity(gpar & 0x55) & 0x04); /* P1' */
+
+ ecc[2] = ~(lowbits | ((pbits & 0x100) >> 7) | ((pprime & 0x100) >> 8));
+ /* now intermix bits for ecc[1] (P1024..P128') and ecc[0] (P64..P8') */
+ ecc[1] = ~( (pbits & 0x80) >> 0 | ((pprime & 0x80) >> 1)
+ | ((pbits & 0x40) >> 1) | ((pprime & 0x40) >> 2)
+ | ((pbits & 0x20) >> 2) | ((pprime & 0x20) >> 3)
+ | ((pbits & 0x10) >> 3) | ((pprime & 0x10) >> 4));
+
+ ecc[0] = ~( (pbits & 0x8) << 4 | ((pprime & 0x8) << 3)
+ | ((pbits & 0x4) << 3) | ((pprime & 0x4) << 2)
+ | ((pbits & 0x2) << 2) | ((pprime & 0x2) << 1)
+ | ((pbits & 0x1) << 1) | ((pprime & 0x1) << 0));
+ return 0;
+}
+
+/* This is the method in the chip->ecc field */
+static int nomadik_ecc_calculate(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ return ecc512(dat, ecc_code);
+}
+
+static int nomadik_ecc_correct(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *r_ecc, uint8_t *c_ecc)
+{
+ struct nand_chip *chip = mtd->priv;
+ uint32_t r, c, d, diff; /*read, calculated, xor of them */
+
+ if (!memcmp(r_ecc, c_ecc, chip->ecc.bytes))
+ return 0;
+
+ /* Reorder the bytes into ascending-order 24 bits -- see manual */
+ r = r_ecc[2] << 22 | r_ecc[1] << 14 | r_ecc[0] << 6 | r_ecc[2] >> 2;
+ c = c_ecc[2] << 22 | c_ecc[1] << 14 | c_ecc[0] << 6 | c_ecc[2] >> 2;
+ diff = (r ^ c) & ((1<<24)-1); /* use 24 bits only */
+
+ /* If 12 bits are different, one per pair, it's correctable */
+ if (((diff | (diff>>1)) & 0x555555) == 0x555555) {
+ int bit = ((diff & 2) >> 1)
+ | ((diff & 0x8) >> 2) | ((diff & 0x20) >> 3);
+ int byte;
+
+ d = diff >> 6; /* remove bit-order info */
+ byte = ((d & 2) >> 1)
+ | ((d & 0x8) >> 2) | ((d & 0x20) >> 3)
+ | ((d & 0x80) >> 4) | ((d & 0x200) >> 5)
+ | ((d & 0x800) >> 6) | ((d & 0x2000) >> 7)
+ | ((d & 0x8000) >> 8) | ((d & 0x20000) >> 9);
+ /* correct the single bit */
+ dat[byte] ^= 1<<bit;
+ return 0;
+ }
+ /* If 1 bit only differs, it's one bit error in ECC, ignore */
+ if ((diff ^ (1 << (ffs(diff) - 1))) == 0)
+ return 0;
+ /* Otherwise, uncorrectable */
+ return -1;
+}
+
+static void nomadik_ecc_hwctl(struct mtd_info *mtd, int mode)
+{ /* mandatory in the structure but not used here */ }
+
+
+/* This is the layout used by older installations, we keep compatible */
+struct nand_ecclayout nomadik_ecc_layout = {
+ .eccbytes = 3 * 4,
+ .eccpos = { /* each subpage has 16 bytes: pos 2,3,4 hosts ECC */
+ 0x02, 0x03, 0x04,
+ 0x12, 0x13, 0x14,
+ 0x22, 0x23, 0x24,
+ 0x32, 0x33, 0x34},
+ .oobfree = { {0x08, 0x08}, {0x18, 0x08}, {0x28, 0x08}, {0x38, 0x08} },
+};
+
+#define MASK_ALE (1 << 24) /* our ALE is AD21 */
+#define MASK_CLE (1 << 23) /* our CLE is AD22 */
+
+/* This is copied from the AT91SAM9 devices (Stelian Pop, Lead Tech Design) */
+static void nomadik_nand_hwcontrol(struct mtd_info *mtd,
+ int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ u32 pcr0 = readl(REG_FSMC_PCR0);
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
+ IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
+
+ if (ctrl & NAND_CLE)
+ IO_ADDR_W |= MASK_CLE;
+ if (ctrl & NAND_ALE)
+ IO_ADDR_W |= MASK_ALE;
+
+ if (ctrl & NAND_NCE)
+ writel(pcr0 | 0x4, REG_FSMC_PCR0);
+ else
+ writel(pcr0 & ~0x4, REG_FSMC_PCR0);
+
+ this->IO_ADDR_W = (void *) IO_ADDR_W;
+ this->IO_ADDR_R = (void *) IO_ADDR_W;
+ }
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, this->IO_ADDR_W);
+}
+
+/* Returns 1 when ready; upper layers timeout at 20ms with timer routines */
+static int nomadik_nand_ready(struct mtd_info *mtd)
+{
+ return 1; /* The ready bit is handled in hardware */
+}
+
+/* Copy a buffer 32bits at a time: faster than defualt method which is 8bit */
+static void nomadik_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ int i;
+ struct nand_chip *chip = mtd->priv;
+ u32 *p = (u32 *) buf;
+
+ len >>= 2;
+ writel(0, REG_FSMC_ECCR0);
+ for (i = 0; i < len; i++)
+ p[i] = readl(chip->IO_ADDR_R);
+}
+
+int board_nand_init(struct nand_chip *chip)
+{
+ /* Set up the FSMC_PCR0 for nand access*/
+ writel(0x0000004a, REG_FSMC_PCR0);
+ /* Set up FSMC_PMEM0, FSMC_PATT0 with timing data for access */
+ writel(0x00020401, REG_FSMC_PMEM0);
+ writel(0x00020404, REG_FSMC_PATT0);
+
+ chip->options = NAND_COPYBACK | NAND_CACHEPRG | NAND_NO_PADDING;
+ chip->cmd_ctrl = nomadik_nand_hwcontrol;
+ chip->dev_ready = nomadik_nand_ready;
+ /* The chip allows 32bit reads, so avoid the default 8bit copy */
+ chip->read_buf = nomadik_nand_read_buf;
+
+ /* ECC: follow the hardware-defined rulse, but do it in sw */
+ chip->ecc.mode = NAND_ECC_HW;
+ chip->ecc.bytes = 3;
+ chip->ecc.size = 512;
+ chip->ecc.layout = &nomadik_ecc_layout;
+ chip->ecc.calculate = nomadik_ecc_calculate;
+ chip->ecc.hwctl = nomadik_ecc_hwctl;
+ chip->ecc.correct = nomadik_ecc_correct;
+
+ return 0;
+}
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 0f980ab..d0efd73 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -25,6 +25,7 @@
LIB := $(obj)libserial.a
+COBJS-$(CONFIG_ARM_DCC) += arm_dcc.o
COBJS-$(CONFIG_ATMEL_USART) += atmel_usart.o
COBJS-$(CONFIG_MCFUART) += mcfuart.o
COBJS-$(CONFIG_NS9750_UART) += ns9750_serial.o
diff --git a/drivers/serial/arm_dcc.c b/drivers/serial/arm_dcc.c
new file mode 100644
index 0000000..5a7fb6b
--- /dev/null
+++ b/drivers/serial/arm_dcc.c
@@ -0,0 +1,226 @@
+/*
+ * Copyright (C) 2004-2007 ARM Limited.
+ * Copyright (C) 2008 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * As a special exception, if other files instantiate templates or use macros
+ * or inline functions from this file, or you compile this file and link it
+ * with other works to produce a work based on this file, this file does not
+ * by itself cause the resulting work to be covered by the GNU General Public
+ * License. However the source code for this file must still be made available
+ * in accordance with section (3) of the GNU General Public License.
+
+ * This exception does not invalidate any other reasons why a work based on
+ * this file might be covered by the GNU General Public License.
+ */
+
+#include <common.h>
+#include <devices.h>
+
+#define DCC_ARM9_RBIT (1 << 0)
+#define DCC_ARM9_WBIT (1 << 1)
+#define DCC_ARM11_RBIT (1 << 30)
+#define DCC_ARM11_WBIT (1 << 29)
+
+#define read_core_id(x) do { \
+ __asm__ ("mrc p15, 0, %0, c0, c0, 0\n" : "=r" (x)); \
+ x = (x >> 4) & 0xFFF; \
+ } while (0);
+
+/*
+ * ARM9
+ */
+#define write_arm9_dcc(x) \
+ __asm__ volatile ("mcr p14, 0, %0, c1, c0, 0\n" : : "r" (x))
+
+#define read_arm9_dcc(x) \
+ __asm__ volatile ("mrc p14, 0, %0, c1, c0, 0\n" : "=r" (x))
+
+#define status_arm9_dcc(x) \
+ __asm__ volatile ("mrc p14, 0, %0, c0, c0, 0\n" : "=r" (x))
+
+#define can_read_arm9_dcc(x) do { \
+ status_arm9_dcc(x); \
+ x &= DCC_ARM9_RBIT; \
+ } while (0);
+
+#define can_write_arm9_dcc(x) do { \
+ status_arm9_dcc(x); \
+ x &= DCC_ARM9_WBIT; \
+ x = (x == 0); \
+ } while (0);
+
+/*
+ * ARM11
+ */
+#define write_arm11_dcc(x) \
+ __asm__ volatile ("mcr p14, 0, %0, c0, c5, 0\n" : : "r" (x))
+
+#define read_arm11_dcc(x) \
+ __asm__ volatile ("mrc p14, 0, %0, c0, c5, 0\n" : "=r" (x))
+
+#define status_arm11_dcc(x) \
+ __asm__ volatile ("mrc p14, 0, %0, c0, c1, 0\n" : "=r" (x))
+
+#define can_read_arm11_dcc(x) do { \
+ status_arm11_dcc(x); \
+ x &= DCC_ARM11_RBIT; \
+ } while (0);
+
+#define can_write_arm11_dcc(x) do { \
+ status_arm11_dcc(x); \
+ x &= DCC_ARM11_WBIT; \
+ x = (x == 0); \
+ } while (0);
+
+#define TIMEOUT_COUNT 0x4000000
+
+static enum {
+ arm9_and_earlier,
+ arm11_and_later
+} arm_type = arm9_and_earlier;
+
+#ifndef CONFIG_ARM_DCC_MULTI
+#define arm_dcc_init serial_init
+void serial_setbrg(void) {}
+#define arm_dcc_getc serial_getc
+#define arm_dcc_putc serial_putc
+#define arm_dcc_puts serial_puts
+#define arm_dcc_tstc serial_tstc
+#endif
+
+int arm_dcc_init(void)
+{
+ register unsigned int id;
+
+ read_core_id(id);
+
+ if (id >= 0xb00)
+ arm_type = arm11_and_later;
+ else
+ arm_type = arm9_and_earlier;
+
+ return 0;
+}
+
+int arm_dcc_getc(void)
+{
+ int ch;
+ register unsigned int reg;
+
+ switch (arm_type) {
+ case arm11_and_later:
+ do {
+ can_read_arm11_dcc(reg);
+ } while (!reg);
+ read_arm11_dcc(ch);
+ break;
+
+ case arm9_and_earlier:
+ default:
+ do {
+ can_read_arm9_dcc(reg);
+ } while (!reg);
+ read_arm9_dcc(ch);
+ break;
+ }
+
+ return ch;
+}
+
+void arm_dcc_putc(char ch)
+{
+ register unsigned int reg;
+ unsigned int timeout_count = TIMEOUT_COUNT;
+
+ switch (arm_type) {
+ case arm11_and_later:
+ while (--timeout_count) {
+ can_write_arm11_dcc(reg);
+ if (reg)
+ break;
+ }
+ if (timeout_count == 0)
+ return;
+ else
+ write_arm11_dcc(ch);
+ break;
+
+ case arm9_and_earlier:
+ default:
+ while (--timeout_count) {
+ can_write_arm9_dcc(reg);
+ if (reg)
+ break;
+ }
+ if (timeout_count == 0)
+ return;
+ else
+ write_arm9_dcc(ch);
+ break;
+ }
+}
+
+void arm_dcc_puts(const char *s)
+{
+ while (*s)
+ arm_dcc_putc(*s++);
+}
+
+int arm_dcc_tstc(void)
+{
+ register unsigned int reg;
+
+ switch (arm_type) {
+ case arm11_and_later:
+ can_read_arm11_dcc(reg);
+ break;
+ case arm9_and_earlier:
+ default:
+ can_read_arm9_dcc(reg);
+ break;
+ }
+
+ return reg;
+}
+
+#ifdef CONFIG_ARM_DCC_MULTI
+static device_t arm_dcc_dev;
+
+int drv_arm_dcc_init(void)
+{
+ int rc;
+
+ /* Device initialization */
+ memset(&arm_dcc_dev, 0, sizeof(arm_dcc_dev));
+
+ strcpy(arm_dcc_dev.name, "dcc");
+ arm_dcc_dev.ext = 0; /* No extensions */
+ arm_dcc_dev.flags = DEV_FLAGS_INPUT | DEV_FLAGS_OUTPUT;
+ arm_dcc_dev.tstc = arm_dcc_tstc; /* 'tstc' function */
+ arm_dcc_dev.getc = arm_dcc_getc; /* 'getc' function */
+ arm_dcc_dev.putc = arm_dcc_putc; /* 'putc' function */
+ arm_dcc_dev.puts = arm_dcc_puts; /* 'puts' function */
+
+ rc = device_register(&arm_dcc_dev);
+
+ if (rc == 0) {
+ arm_dcc_init();
+ return 1;
+ }
+
+ return 0;
+}
+#endif
diff --git a/include/asm-arm/arch-omap3/cpu.h b/include/asm-arm/arch-omap3/cpu.h
index 69c0b36..5b344f8 100644
--- a/include/asm-arm/arch-omap3/cpu.h
+++ b/include/asm-arm/arch-omap3/cpu.h
@@ -35,11 +35,31 @@
unsigned short gpmc_nwe; /* 0xC4 */
unsigned char res2[0x22A];
unsigned int status; /* 0x2F0 */
+ unsigned int gpstatus; /* 0x2F4 */
+ unsigned char res3[0x08];
+ unsigned int rpubkey_0; /* 0x300 */
+ unsigned int rpubkey_1; /* 0x304 */
+ unsigned int rpubkey_2; /* 0x308 */
+ unsigned int rpubkey_3; /* 0x30C */
+ unsigned int rpubkey_4; /* 0x310 */
+ unsigned char res4[0x04];
+ unsigned int randkey_0; /* 0x318 */
+ unsigned int randkey_1; /* 0x31C */
+ unsigned int randkey_2; /* 0x320 */
+ unsigned int randkey_3; /* 0x324 */
+ unsigned char res5[0x124];
+ unsigned int ctrl_omap_stat; /* 0x44C */
} ctrl_t;
#else /* __ASSEMBLY__ */
#define CONTROL_STATUS 0x2F0
#endif /* __ASSEMBLY__ */
+/* cpu type */
+#define OMAP3503 0x5c00
+#define OMAP3515 0x1c00
+#define OMAP3525 0x4c00
+#define OMAP3530 0x0c00
+
/* device type */
#define DEVICE_MASK (0x7 << 8)
#define SYSBOOT_MASK 0x1F
diff --git a/include/asm-arm/arch-omap3/mmc_host_def.h b/include/asm-arm/arch-omap3/mmc_host_def.h
index dfb376a..aa751c9 100644
--- a/include/asm-arm/arch-omap3/mmc_host_def.h
+++ b/include/asm-arm/arch-omap3/mmc_host_def.h
@@ -25,30 +25,50 @@
#ifndef MMC_HOST_DEF_H
#define MMC_HOST_DEF_H
+/* T2 Register definitions */
+#define T2_BASE 0x48002000
+
+typedef struct t2 {
+ unsigned char res1[0x274];
+ unsigned int devconf0; /* 0x274 */
+ unsigned char res2[0x2A8];
+ unsigned int pbias_lite; /* 0x520 */
+} t2_t;
+
+#define MMCSDIO1ADPCLKISEL (1 << 24)
+
+#define PBIASLITEPWRDNZ0 (1 << 1)
+#define PBIASSPEEDCTRL0 (1 << 2)
+#define PBIASLITEPWRDNZ1 (1 << 9)
+
/*
* OMAP HSMMC register definitions
*/
-#define OMAP_HSMMC_SYSCONFIG (*(unsigned int *) 0x4809C010)
-#define OMAP_HSMMC_SYSSTATUS (*(unsigned int *) 0x4809C014)
-#define OMAP_HSMMC_CON (*(unsigned int *) 0x4809C02C)
-#define OMAP_HSMMC_BLK (*(unsigned int *) 0x4809C104)
-#define OMAP_HSMMC_ARG (*(unsigned int *) 0x4809C108)
-#define OMAP_HSMMC_CMD (*(unsigned int *) 0x4809C10C)
-#define OMAP_HSMMC_RSP10 (*(unsigned int *) 0x4809C110)
-#define OMAP_HSMMC_RSP32 (*(unsigned int *) 0x4809C114)
-#define OMAP_HSMMC_RSP54 (*(unsigned int *) 0x4809C118)
-#define OMAP_HSMMC_RSP76 (*(unsigned int *) 0x4809C11C)
-#define OMAP_HSMMC_DATA (*(unsigned int *) 0x4809C120)
-#define OMAP_HSMMC_PSTATE (*(unsigned int *) 0x4809C124)
-#define OMAP_HSMMC_HCTL (*(unsigned int *) 0x4809C128)
-#define OMAP_HSMMC_SYSCTL (*(unsigned int *) 0x4809C12C)
-#define OMAP_HSMMC_STAT (*(unsigned int *) 0x4809C130)
-#define OMAP_HSMMC_IE (*(unsigned int *) 0x4809C134)
-#define OMAP_HSMMC_CAPA (*(unsigned int *) 0x4809C140)
+#define OMAP_HSMMC_BASE 0x4809C000
-/* T2 Register definitions */
-#define CONTROL_DEV_CONF0 (*(unsigned int *) 0x48002274)
-#define CONTROL_PBIAS_LITE (*(unsigned int *) 0x48002520)
+typedef struct hsmmc {
+ unsigned char res1[0x10];
+ unsigned int sysconfig; /* 0x10 */
+ unsigned int sysstatus; /* 0x14 */
+ unsigned char res2[0x14];
+ unsigned int con; /* 0x2C */
+ unsigned char res3[0xD4];
+ unsigned int blk; /* 0x104 */
+ unsigned int arg; /* 0x108 */
+ unsigned int cmd; /* 0x10C */
+ unsigned int rsp10; /* 0x110 */
+ unsigned int rsp32; /* 0x114 */
+ unsigned int rsp54; /* 0x118 */
+ unsigned int rsp76; /* 0x11C */
+ unsigned int data; /* 0x120 */
+ unsigned int pstate; /* 0x124 */
+ unsigned int hctl; /* 0x128 */
+ unsigned int sysctl; /* 0x12C */
+ unsigned int stat; /* 0x130 */
+ unsigned int ie; /* 0x134 */
+ unsigned char res4[0x8];
+ unsigned int capa; /* 0x140 */
+} hsmmc_t;
/*
* OMAP HS MMC Bit definitions
@@ -159,8 +179,6 @@
} mmc_card_data;
#define mmc_reg_out(addr, mask, val)\
- (addr) = (((addr)) & (~(mask))) | ((val) & (mask));
-#define mmc_reg_out(addr, mask, val)\
- (addr) = (((addr)) & (~(mask))) | ((val) & (mask));
+ writel((readl(addr) & (~(mask))) | ((val) & (mask)), (addr))
#endif /* MMC_HOST_DEF_H */
diff --git a/include/asm-arm/arch-omap3/omap3.h b/include/asm-arm/arch-omap3/omap3.h
index 7473656..02e36d7 100644
--- a/include/asm-arm/arch-omap3/omap3.h
+++ b/include/asm-arm/arch-omap3/omap3.h
@@ -97,7 +97,8 @@
typedef struct gpio {
unsigned char res1[0x34];
unsigned int oe; /* 0x34 */
- unsigned char res2[0x58];
+ unsigned int datain; /* 0x38 */
+ unsigned char res2[0x54];
unsigned int cleardataout; /* 0x90 */
unsigned int setdataout; /* 0x94 */
} gpio_t;
@@ -202,6 +203,8 @@
#define VAUX2_DEDICATED 0x79
#define VAUX3_DEV_GRP 0x7A
#define VAUX3_DEDICATED 0x7D
+#define VMMC1_DEV_GRP 0x82
+#define VMMC1_DEDICATED 0x85
#define VPLL2_DEV_GRP 0x8E
#define VPLL2_DEDICATED 0x91
#define VDAC_DEV_GRP 0x96
@@ -214,5 +217,6 @@
#define VAUX3_VSEL_28 0x03
#define VPLL2_VSEL_18 0x05
#define VDAC_VSEL_18 0x03
+#define VMMC1_VSEL_30 0x02
#endif
diff --git a/include/asm-arm/arch-omap3/sys_proto.h b/include/asm-arm/arch-omap3/sys_proto.h
index 4c624e8..ab3e168 100644
--- a/include/asm-arm/arch-omap3/sys_proto.h
+++ b/include/asm-arm/arch-omap3/sys_proto.h
@@ -25,7 +25,6 @@
u32 board_type_v1;
u32 board_type_v2;
u32 mtype;
- char *cpu_string;
char *board_string;
char *nand_string;
} omap3_sysinfo;
diff --git a/include/configs/nmdk8815.h b/include/configs/nmdk8815.h
index 01de08f..543780d 100644
--- a/include/configs/nmdk8815.h
+++ b/include/configs/nmdk8815.h
@@ -25,6 +25,8 @@
#ifndef __CONFIG_H
#define __CONFIG_H
+#include <nomadik.h>
+
#define CONFIG_ARM926EJS
#define CONFIG_NOMADIK
#define CONFIG_NOMADIK_8815
@@ -35,12 +37,18 @@
/* commands */
#include <config_cmd_default.h>
+
+#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
-/* At this point there is no flash driver, so remove some commands */
-#undef CONFIG_CMD_ENV
+#define CONFIG_CMD_NFS
+/* There is no NOR flash, so undefine these commands */
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
+#define CONFIG_SYS_NO_FLASH
+/* There is NAND storage */
+#define CONFIG_NAND_NOMADIK
+#define CONFIG_CMD_JFFS2
/* user interface */
#define CONFIG_SYS_LONGHELP
@@ -118,13 +126,11 @@
#define CONFIG_MTD_ONENAND_VERIFY_WRITE
#define CONFIG_SYS_ONENAND_BASE 0x30000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-
-#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_NAND_BASE 0x40000000 /* SMPS0n */
#ifdef CONFIG_BOOT_ONENAND
-# undef CONFIG_CMD_NAND /* Temporary: nand and onenand can't coexist */
+# define CONFIG_CMD_ONENAND /* Temporary: nand and onenand can't coexist */
/* Partition Size Start
* XloaderTOC + X-Loader 256KB 0x00000000
* Memory init function 256KB 0x00040000
@@ -142,7 +148,7 @@
#else /* ! CONFIG_BOOT_ONENAND */
-# undef CONFIG_CMD_ONENAND /* Temporary: nand and onenand can't coexist */
+# define CONFIG_CMD_NAND /* Temporary: nand and onenand can't coexist */
# define CONFIG_JFFS2_DEV "nand0"
# define CONFIG_JFFS2_NAND 1 /* For the jffs2 support*/
@@ -150,39 +156,13 @@
# define CONFIG_JFFS2_PART_OFFSET 0x00280000
# define CONFIG_ENV_IS_IN_NAND
-# define CONFIG_ENV_SIZE 0x20000 /*128 Kb*/
+# define CONFIG_ENV_SIZE 0x20000 /* 128 Kb - one sector */
# define CONFIG_ENV_OFFSET (0x8000000 - CONFIG_ENV_SIZE)
#endif /* CONFIG_BOOT_ONENAND */
-/* Temporarily, until we have no driver, env is not in nand */
-#undef CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_IS_NOWHERE
-
/* this is needed to make hello_world.c and other stuff happy */
#define CONFIG_SYS_MAX_FLASH_SECT 512
#define CONFIG_SYS_MAX_FLASH_BANKS 1
-/* base addresses of our peripherals */
-#define NOMADIK_SRC_BASE 0x101E0000 /* System and Reset Cnt */
-#define NOMADIK_PMU_BASE 0x101E9000 /* Power Management Unit */
-#define NOMADIK_MPMC_BASE 0x10110000 /* SDRAM Controller */
-#define NOMADIK_FSMC_BASE 0x10100000 /* FSMC Controller */
-#define NOMADIK_1NAND_BASE 0x30000000
-#define NOMADIK_GPIO0_BASE 0x101E4000
-#define NOMADIK_GPIO1_BASE 0x101E5000
-#define NOMADIK_GPIO2_BASE 0x101E6000
-#define NOMADIK_GPIO3_BASE 0x101E7000
-#define NOMADIK_CPLD_BASE 0x36000000
-#define NOMADIK_UART0_BASE 0x101FD000
-#define NOMADIK_UART1_BASE 0x101FB000
-#define NOMADIK_UART2_BASE 0x101F2000
-
-#define NOMADIK_I2C1_BASE 0x101F7000 /* I2C1 interface */
-#define NOMADIK_I2C0_BASE 0x101F8000 /* I2C0 interface */
-
-#define NOMADIK_RTC_BASE 0x101E8000
-#define NOMADIK_ETH0_BASE 0x36800300
-#define NOMADIK_CPLD_UART_BASE 0x36480000
-
#endif /* __CONFIG_H */
diff --git a/include/devices.h b/include/devices.h
index 84c4514..3a9881b 100644
--- a/include/devices.h
+++ b/include/devices.h
@@ -98,6 +98,9 @@
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
+#ifdef CONFIG_ARM_DCC_MULTI
+int drv_arm_dcc_init(void);
+#endif
#ifdef CONFIG_LCD
int drv_lcd_init (void);
#endif
diff --git a/include/nomadik.h b/include/nomadik.h
new file mode 100644
index 0000000..d9405fd
--- /dev/null
+++ b/include/nomadik.h
@@ -0,0 +1,39 @@
+/* Collection of constants used to access Nomadik registers */
+
+#ifndef __NOMADIK_H__
+#define __NOMADIK_H__
+
+/* Base addresses of our peripherals */
+#define NOMADIK_SRC_BASE 0x101E0000 /* System and Reset Cnt */
+#define NOMADIK_PMU_BASE 0x101E9000 /* Power Management Unit */
+#define NOMADIK_MPMC_BASE 0x10110000 /* SDRAM Controller */
+#define NOMADIK_FSMC_BASE 0x10100000 /* FSMC Controller */
+#define NOMADIK_1NAND_BASE 0x30000000
+#define NOMADIK_GPIO0_BASE 0x101E4000
+#define NOMADIK_GPIO1_BASE 0x101E5000
+#define NOMADIK_GPIO2_BASE 0x101E6000
+#define NOMADIK_GPIO3_BASE 0x101E7000
+#define NOMADIK_CPLD_BASE 0x36000000
+#define NOMADIK_UART0_BASE 0x101FD000
+#define NOMADIK_UART1_BASE 0x101FB000
+#define NOMADIK_UART2_BASE 0x101F2000
+
+#define NOMADIK_I2C1_BASE 0x101F7000 /* I2C1 interface */
+#define NOMADIK_I2C0_BASE 0x101F8000 /* I2C0 interface */
+
+#define NOMADIK_RTC_BASE 0x101E8000
+#define NOMADIK_ETH0_BASE 0x36800300
+#define NOMADIK_CPLD_UART_BASE 0x36480000
+
+/* Chip select registers ("Flexible Static Memory Controller") */
+
+#define REG_FSMC_BCR0 (NOMADIK_FSMC_BASE + 0x00)
+#define REG_FSMC_BTR0 (NOMADIK_FSMC_BASE + 0x04)
+#define REG_FSMC_BCR1 (NOMADIK_FSMC_BASE + 0x08)
+#define REG_FSMC_BTR1 (NOMADIK_FSMC_BASE + 0x0c)
+#define REG_FSMC_PCR0 (NOMADIK_FSMC_BASE + 0x40)
+#define REG_FSMC_PMEM0 (NOMADIK_FSMC_BASE + 0x48)
+#define REG_FSMC_PATT0 (NOMADIK_FSMC_BASE + 0x4c)
+#define REG_FSMC_ECCR0 (NOMADIK_FSMC_BASE + 0x54)
+
+#endif /* __NOMADIK_H__ */
diff --git a/lib_arm/board.c b/lib_arm/board.c
index f125d38..09eaaf2 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -145,6 +145,9 @@
* but let's get it working (again) first...
*/
+#if defined(CONFIG_ARM_DCC) && !defined(CONFIG_BAUDRATE)
+#define CONFIG_BAUDRATE 115200
+#endif
static int init_baudrate (void)
{
char tmp[64]; /* long enough for environment variables */