arch/arm/dts/sun50i-a64-olinuxino.dts - platform/external/u-boot - Gitiles

 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 // Copyright (C) 2017 Jagan Teki <jteki@openedev.com>

 /dts-v1/;

 #include "sun50i-a64.dtsi"
 #include "sun50i-a64-cpu-opp.dtsi"

 #include <dt-bindings/gpio/gpio.h>

 / {
 	model = "Olimex A64-Olinuxino";
 	compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64";

 	aliases {
 		ethernet0 = &emac;
 		serial0 = &uart0;
 	};

 	chosen {
 		stdout-path = "serial0:115200n8";
 	};

 	hdmi-connector {
 		compatible = "hdmi-connector";
 		type = "a";

 		port {
 			hdmi_con_in: endpoint {
 				remote-endpoint = <&hdmi_out_con>;
 			};
 		};
 	};

 	leds {
 		compatible = "gpio-leds";

 		led-0 {
 			label = "a64-olinuxino:red:user";
 			gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
 		};
 	};

 	reg_usb1_vbus: usb1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb1-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		regulator-boot-on;
 		enable-active-high;
 		gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */
 		status = "okay";
 	};

 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
 };

 &codec {
 	status = "okay";
 };

 &codec_analog {
 	cpvdd-supply = <&reg_eldo1>;
 	status = "okay";
 };

 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &cpu1 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &cpu2 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &cpu3 {
 	cpu-supply = <&reg_dcdc2>;
 };

 &dai {
 	status = "okay";
 };

 &de {
 	status = "okay";
 };

 &ehci0 {
 	status = "okay";
 };

 &ehci1 {
 	status = "okay";
 };

 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
 	phy-mode = "rgmii";
 	phy-handle = <&ext_rgmii_phy>;
 	phy-supply = <&reg_dcdc1>;
 	allwinner,tx-delay-ps = <600>;
 	status = "okay";
 };

 &hdmi {
 	hvcc-supply = <&reg_dldo1>;
 	status = "okay";
 };

 &hdmi_out {
 	hdmi_out_con: endpoint {
 		remote-endpoint = <&hdmi_con_in>;
 	};
 };

 &mdio {
 	ext_rgmii_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 	};
 };

 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
 };

 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	vqmmc-supply = <&reg_dldo4>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";

 	rtl8723bs: wifi@1 {
 		reg = <1>;
 		interrupt-parent = <&r_pio>;
 		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
 		interrupt-names = "host-wake";
 	};
 };

 &ohci0 {
 	status = "okay";
 };

 &ohci1 {
 	status = "okay";
 };

 &pio {
 	vcc-pc-supply = <&reg_dcdc1>;
 	vcc-pd-supply = <&reg_dcdc1>;
 	vcc-pe-supply = <&reg_aldo1>;
 	vcc-pg-supply = <&reg_dldo4>;
 };

 &r_pio {
 	/*
 	 * FIXME: We can't add that supply for now since it would
 	 * create a circular dependency between pinctrl, the regulator
 	 * and the RSB Bus.
 	 *
 	 * vcc-pl-supply = <&reg_aldo2>;
 	 */
 };

 &pio {
 	vcc-pa-supply = <&reg_dcdc1>;
 	vcc-pb-supply = <&reg_dcdc1>;
 	vcc-pc-supply = <&reg_dcdc1>;
 	vcc-pd-supply = <&reg_dcdc1>;
 	vcc-pe-supply = <&reg_aldo1>;
 	vcc-pf-supply = <&reg_dcdc1>;
 	vcc-pg-supply = <&reg_dldo4>;
 	vcc-ph-supply = <&reg_dcdc1>;
 };

 &r_rsb {
 	status = "okay";

 	axp803: pmic@3a3 {
 		compatible = "x-powers,axp803";
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		x-powers,drive-vbus-en;	/* set N_VBUSEN as output pin */
 	};
 };

 /* VCC-PL is powered by aldo2 but we cannot add it as the RSB */
 /* interface used to talk to the PMIC in on the PL pins */
 /* &r_pio { */
 /*	vcc-pl-supply = <&reg_aldo2>; */
 /* }; */

 #include "axp803.dtsi"

 &ac_power_supply {
 	status = "okay";
 };

 &battery_power_supply {
 	status = "okay";
 };

 &reg_aldo1 {
 	regulator-always-on;
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "vcc-pe";
 };

 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-pl";
 };

 &reg_aldo3 {
 	regulator-always-on;
 	regulator-min-microvolt = <3000000>;
 	regulator-max-microvolt = <3000000>;
 	regulator-name = "vcc-pll-avcc";
 };

 &reg_dcdc1 {
 	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-3v3";
 };

 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1040000>;
 	regulator-max-microvolt = <1300000>;
 	regulator-name = "vdd-cpux";
 };

 /* DCDC3 is polyphased with DCDC2 */

 /*
  * The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal
  * 1.35V that the PMIC can drive.
  */
 &reg_dcdc5 {
 	regulator-always-on;
 	regulator-min-microvolt = <1360000>;
 	regulator-max-microvolt = <1360000>;
 	regulator-name = "vcc-ddr3";
 };

 &reg_dcdc6 {
 	regulator-always-on;
 	regulator-min-microvolt = <1100000>;
 	regulator-max-microvolt = <1100000>;
 	regulator-name = "vdd-sys";
 };

 &reg_dldo1 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-hdmi";
 };

 &reg_dldo2 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-mipi";
 };

 &reg_dldo3 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "vcc-avdd-csi";
 };

 &reg_dldo4 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-wifi-io";
 };

 &reg_drivevbus {
 	regulator-name = "usb0-vbus";
 	status = "okay";
 };

 &reg_eldo1 {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
 	regulator-name = "cpvdd";
 };

 &reg_eldo2 {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
 	regulator-name = "vcc-dvdd-csi";
 };

 &reg_fldo1 {
 	regulator-min-microvolt = <1200000>;
 	regulator-max-microvolt = <1200000>;
 	regulator-name = "vcc-1v2-hsic";
 };

 /*
  * The A64 chip cannot work without this regulator off, although
  * it seems to be only driving the AR100 core.
  * Maybe we don't still know well about CPUs domain.
  */
 &reg_fldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1100000>;
 	regulator-max-microvolt = <1100000>;
 	regulator-name = "vdd-cpus";
 };

 &reg_rtc_ldo {
 	regulator-name = "vcc-rtc";
 };

 &simplefb_hdmi {
 	vcc-hdmi-supply = <&reg_dldo1>;
 };

 &sound {
 	simple-audio-card,aux-devs = <&codec_analog>;
 	simple-audio-card,widgets = "Microphone", "Microphone Jack Left",
 		    "Microphone", "Microphone Jack Right",
 		    "Headphone", "Headphone Jack";
 	simple-audio-card,routing = "Left DAC", "DACL",
 		    "Right DAC", "DACR",
 		    "Headphone Jack", "HP",
 		    "ADCL", "Left ADC",
 		    "ADCR", "Right ADC",
 		    "Microphone Jack Left", "MBIAS",
 		    "MIC1", "Microphone Jack Left",
 		    "Microphone Jack Right", "MBIAS",
 		    "MIC2", "Microphone Jack Right";
 	status = "okay";
 };

 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };

 &usb_otg {
 	dr_mode = "otg";
 	status = "okay";
 };

 &usbphy {
 	status = "okay";
 	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
 	usb0_vbus-supply = <&reg_drivevbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 };
	// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
	// Copyright (C) 2017 Jagan Teki <jteki@openedev.com>

	/dts-v1/;

	#include "sun50i-a64.dtsi"
	#include "sun50i-a64-cpu-opp.dtsi"

	#include <dt-bindings/gpio/gpio.h>

	/ {
	model = "Olimex A64-Olinuxino";
	compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64";

	aliases {
	ethernet0 = &emac;
	serial0 = &uart0;
	};

	chosen {
	stdout-path = "serial0:115200n8";
	};

	hdmi-connector {
	compatible = "hdmi-connector";
	type = "a";

	port {
	hdmi_con_in: endpoint {
	remote-endpoint = <&hdmi_out_con>;
	};
	};
	};

	leds {
	compatible = "gpio-leds";

	led-0 {
	label = "a64-olinuxino:red:user";
	gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
	};
	};

	reg_usb1_vbus: usb1-vbus {
	compatible = "regulator-fixed";
	regulator-name = "usb1-vbus";
	regulator-min-microvolt = <5000000>;
	regulator-max-microvolt = <5000000>;
	regulator-boot-on;
	enable-active-high;
	gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */
	status = "okay";
	};

	wifi_pwrseq: wifi_pwrseq {
	compatible = "mmc-pwrseq-simple";
	reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
	};
	};

	&codec {
	status = "okay";
	};

	&codec_analog {
	cpvdd-supply = <&reg_eldo1>;
	status = "okay";
	};

	&cpu0 {
	cpu-supply = <&reg_dcdc2>;
	};

	&cpu1 {
	cpu-supply = <&reg_dcdc2>;
	};

	&cpu2 {
	cpu-supply = <&reg_dcdc2>;
	};

	&cpu3 {
	cpu-supply = <&reg_dcdc2>;
	};

	&dai {
	status = "okay";
	};

	&de {
	status = "okay";
	};

	&ehci0 {
	status = "okay";
	};

	&ehci1 {
	status = "okay";
	};

	&emac {
	pinctrl-names = "default";
	pinctrl-0 = <&rgmii_pins>;
	phy-mode = "rgmii";
	phy-handle = <&ext_rgmii_phy>;
	phy-supply = <&reg_dcdc1>;
	allwinner,tx-delay-ps = <600>;
	status = "okay";
	};

	&hdmi {
	hvcc-supply = <&reg_dldo1>;
	status = "okay";
	};

	&hdmi_out {
	hdmi_out_con: endpoint {
	remote-endpoint = <&hdmi_con_in>;
	};
	};

	&mdio {
	ext_rgmii_phy: ethernet-phy@1 {
	compatible = "ethernet-phy-ieee802.3-c22";
	reg = <1>;
	};
	};

	&mmc0 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc0_pins>;
	vmmc-supply = <&reg_dcdc1>;
	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
	disable-wp;
	bus-width = <4>;
	status = "okay";
	};

	&mmc1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
	vmmc-supply = <&reg_dcdc1>;
	vqmmc-supply = <&reg_dldo4>;
	mmc-pwrseq = <&wifi_pwrseq>;
	bus-width = <4>;
	non-removable;
	status = "okay";

	rtl8723bs: wifi@1 {
	reg = <1>;
	interrupt-parent = <&r_pio>;
	interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
	interrupt-names = "host-wake";
	};
	};

	&ohci0 {
	status = "okay";
	};

	&ohci1 {
	status = "okay";
	};

	&pio {
	vcc-pc-supply = <&reg_dcdc1>;
	vcc-pd-supply = <&reg_dcdc1>;
	vcc-pe-supply = <&reg_aldo1>;
	vcc-pg-supply = <&reg_dldo4>;
	};

	&r_pio {
	/*
	* FIXME: We can't add that supply for now since it would
	* create a circular dependency between pinctrl, the regulator
	* and the RSB Bus.
	*
	* vcc-pl-supply = <&reg_aldo2>;
	*/
	};

	&pio {
	vcc-pa-supply = <&reg_dcdc1>;
	vcc-pb-supply = <&reg_dcdc1>;
	vcc-pc-supply = <&reg_dcdc1>;
	vcc-pd-supply = <&reg_dcdc1>;
	vcc-pe-supply = <&reg_aldo1>;
	vcc-pf-supply = <&reg_dcdc1>;
	vcc-pg-supply = <&reg_dldo4>;
	vcc-ph-supply = <&reg_dcdc1>;
	};

	&r_rsb {
	status = "okay";

	axp803: pmic@3a3 {
	compatible = "x-powers,axp803";
	reg = <0x3a3>;
	interrupt-parent = <&r_intc>;
	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
	x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
	};
	};

	/* VCC-PL is powered by aldo2 but we cannot add it as the RSB */
	/* interface used to talk to the PMIC in on the PL pins */
	/* &r_pio { */
	/* vcc-pl-supply = <&reg_aldo2>; */
	/* }; */

	#include "axp803.dtsi"

	&ac_power_supply {
	status = "okay";
	};

	&battery_power_supply {
	status = "okay";
	};

	&reg_aldo1 {
	regulator-always-on;
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-name = "vcc-pe";
	};

	&reg_aldo2 {
	regulator-always-on;
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-pl";
	};

	&reg_aldo3 {
	regulator-always-on;
	regulator-min-microvolt = <3000000>;
	regulator-max-microvolt = <3000000>;
	regulator-name = "vcc-pll-avcc";
	};

	&reg_dcdc1 {
	regulator-always-on;
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-3v3";
	};

	&reg_dcdc2 {
	regulator-always-on;
	regulator-min-microvolt = <1040000>;
	regulator-max-microvolt = <1300000>;
	regulator-name = "vdd-cpux";
	};

	/* DCDC3 is polyphased with DCDC2 */

	/*
	* The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal
	* 1.35V that the PMIC can drive.
	*/
	&reg_dcdc5 {
	regulator-always-on;
	regulator-min-microvolt = <1360000>;
	regulator-max-microvolt = <1360000>;
	regulator-name = "vcc-ddr3";
	};

	&reg_dcdc6 {
	regulator-always-on;
	regulator-min-microvolt = <1100000>;
	regulator-max-microvolt = <1100000>;
	regulator-name = "vdd-sys";
	};

	&reg_dldo1 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-hdmi";
	};

	&reg_dldo2 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-mipi";
	};

	&reg_dldo3 {
	regulator-min-microvolt = <2800000>;
	regulator-max-microvolt = <2800000>;
	regulator-name = "vcc-avdd-csi";
	};

	&reg_dldo4 {
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-name = "vcc-wifi-io";
	};

	&reg_drivevbus {
	regulator-name = "usb0-vbus";
	status = "okay";
	};

	&reg_eldo1 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-name = "cpvdd";
	};

	&reg_eldo2 {
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-name = "vcc-dvdd-csi";
	};

	&reg_fldo1 {
	regulator-min-microvolt = <1200000>;
	regulator-max-microvolt = <1200000>;
	regulator-name = "vcc-1v2-hsic";
	};

	/*
	* The A64 chip cannot work without this regulator off, although
	* it seems to be only driving the AR100 core.
	* Maybe we don't still know well about CPUs domain.
	*/
	&reg_fldo2 {
	regulator-always-on;
	regulator-min-microvolt = <1100000>;
	regulator-max-microvolt = <1100000>;
	regulator-name = "vdd-cpus";
	};

	&reg_rtc_ldo {
	regulator-name = "vcc-rtc";
	};

	&simplefb_hdmi {
	vcc-hdmi-supply = <&reg_dldo1>;
	};

	&sound {
	simple-audio-card,aux-devs = <&codec_analog>;
	simple-audio-card,widgets = "Microphone", "Microphone Jack Left",
	"Microphone", "Microphone Jack Right",
	"Headphone", "Headphone Jack";
	simple-audio-card,routing = "Left DAC", "DACL",
	"Right DAC", "DACR",
	"Headphone Jack", "HP",
	"ADCL", "Left ADC",
	"ADCR", "Right ADC",
	"Microphone Jack Left", "MBIAS",
	"MIC1", "Microphone Jack Left",
	"Microphone Jack Right", "MBIAS",
	"MIC2", "Microphone Jack Right";
	status = "okay";
	};

	&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_pb_pins>;
	status = "okay";
	};

	&usb_otg {
	dr_mode = "otg";
	status = "okay";
	};

	&usbphy {
	status = "okay";
	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
	usb0_vbus-supply = <&reg_drivevbus>;
	usb1_vbus-supply = <&reg_usb1_vbus>;
	};