usb : musb : Adding host controller driver for Mentor USB controller

Adding Mentor USB core functionality and Mentor USB Host controller
functionality for Mentor USB OTG controller (musbhdrc).

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index 0f94963..098d7b6 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -37,6 +37,7 @@
 COBJS-$(CONFIG_USB_EHCI_FSL) += usb_ehci_fsl.o
 COBJS-$(CONFIG_USB_EHCI_PCI) += usb_ehci_pci.o
 COBJS-$(CONFIG_USB_EHCI_IXP4XX) += usb_ehci_ixp.o
+COBJS-$(CONFIG_MUSB_HCD) += musb_hcd.o musb_core.o
 
 # device
 ifdef CONFIG_USB_DEVICE
diff --git a/drivers/usb/musb_core.c b/drivers/usb/musb_core.c
new file mode 100644
index 0000000..ec57fc8
--- /dev/null
+++ b/drivers/usb/musb_core.c
@@ -0,0 +1,141 @@
+/*
+ * Mentor USB OTG Core functionality common for both Host and Device
+ * functionality.
+ *
+ * Copyright (c) 2008 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Author: Thomas Abraham t-abraham@ti.com, Texas Instruments
+ */
+
+#include <common.h>
+
+#include "musb_core.h"
+struct musb_regs *musbr;
+
+/*
+ * program the mentor core to start (enable interrupts, dma, etc.)
+ */
+void musb_start(void)
+{
+	u8 devctl;
+
+	/* disable all interrupts */
+	writew(0, &musbr->intrtxe);
+	writew(0, &musbr->intrrxe);
+	writeb(0, &musbr->intrusbe);
+	writeb(0, &musbr->testmode);
+
+	/* put into basic highspeed mode and start session */
+	writeb(MUSB_POWER_HSENAB, &musbr->power);
+#if defined(CONFIG_MUSB_HCD)
+	devctl = readb(&musbr->devctl);
+	writeb(devctl | MUSB_DEVCTL_SESSION, &musbr->devctl);
+#endif
+}
+
+/*
+ * This function configures the endpoint configuration. The musb hcd or musb
+ * device implementation can use this function to configure the endpoints
+ * and set the FIFO sizes. Note: The summation of FIFO sizes of all endpoints
+ * should not be more than the available FIFO size.
+ *
+ * epinfo	- Pointer to EP configuration table
+ * cnt		- Number of entries in the EP conf table.
+ */
+void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt)
+{
+	u16 csr;
+	u16 fifoaddr = 64; /* First 64 bytes of FIFO reserved for EP0 */
+	u32 fifosize;
+	u8  idx;
+
+	while (cnt--) {
+		/* prepare fifosize to write to register */
+		fifosize = epinfo->epsize >> 3;
+		idx = ffs(fifosize) - 1;
+
+		writeb(epinfo->epnum, &musbr->index);
+		if (epinfo->epdir) {
+			/* Configure fifo size and fifo base address */
+			writeb(idx, &musbr->txfifosz);
+			writew(fifoaddr >> 3, &musbr->txfifoadd);
+#if defined(CONFIG_MUSB_HCD)
+			/* clear the data toggle bit */
+			csr = readw(&musbr->txcsr);
+			writew(csr | MUSB_TXCSR_CLRDATATOG, &musbr->txcsr);
+#endif
+			/* Flush fifo if required */
+			if (csr & MUSB_TXCSR_TXPKTRDY)
+				writew(csr | MUSB_TXCSR_FLUSHFIFO,
+					&musbr->txcsr);
+		} else {
+			/* Configure fifo size and fifo base address */
+			writeb(idx, &musbr->rxfifosz);
+			writew(fifoaddr >> 3, &musbr->rxfifoadd);
+#if defined(CONFIG_MUSB_HCD)
+			/* clear the data toggle bit */
+			csr = readw(&musbr->rxcsr);
+			writew(csr | MUSB_RXCSR_CLRDATATOG, &musbr->rxcsr);
+#endif
+			/* Flush fifo if required */
+			if (csr & MUSB_RXCSR_RXPKTRDY)
+				writew(csr | MUSB_RXCSR_FLUSHFIFO,
+					&musbr->rxcsr);
+		}
+		fifoaddr += epinfo->epsize;
+		epinfo++;
+	}
+}
+
+/*
+ * This function writes data to endpoint fifo
+ *
+ * ep		- endpoint number
+ * length	- number of bytes to write to FIFO
+ * fifo_data	- Pointer to data buffer that contains the data to write
+ */
+void write_fifo(u8 ep, u32 length, void *fifo_data)
+{
+	u8  *data = (u8 *)fifo_data;
+
+	/* select the endpoint index */
+	writeb(ep, &musbr->index);
+
+	/* write the data to the fifo */
+	while (length--)
+		writeb(*data++, &musbr->fifox[ep]);
+}
+
+/*
+ * This function reads data from endpoint fifo
+ *
+ * ep           - endpoint number
+ * length       - number of bytes to read from FIFO
+ * fifo_data    - pointer to data buffer into which data is read
+ */
+void read_fifo(u8 ep, u32 length, void *fifo_data)
+{
+	u8  *data = (u8 *)fifo_data;
+
+	/* select the endpoint index */
+	writeb(ep, &musbr->index);
+
+	/* read the data to the fifo */
+	while (length--)
+		*data++ = readb(&musbr->fifox[ep]);
+}
diff --git a/drivers/usb/musb_core.h b/drivers/usb/musb_core.h
new file mode 100644
index 0000000..9f5ebe7
--- /dev/null
+++ b/drivers/usb/musb_core.h
@@ -0,0 +1,317 @@
+/******************************************************************
+ * Copyright 2008 Mentor Graphics Corporation
+ * Copyright (C) 2008 by Texas Instruments
+ *
+ * This file is part of the Inventra Controller Driver for Linux.
+ *
+ * The Inventra Controller Driver for Linux is free software; you
+ * can redistribute it and/or modify it under the terms of the GNU
+ * General Public License version 2 as published by the Free Software
+ * Foundation.
+ *
+ * The Inventra Controller Driver for Linux is distributed in
+ * the hope that it will be useful, but WITHOUT ANY WARRANTY;
+ * without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public
+ * License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with The Inventra Controller Driver for Linux ; if not,
+ * write to the Free Software Foundation, Inc., 59 Temple Place,
+ * Suite 330, Boston, MA  02111-1307  USA
+ *
+ * ANY DOWNLOAD, USE, REPRODUCTION, MODIFICATION OR DISTRIBUTION
+ * OF THIS DRIVER INDICATES YOUR COMPLETE AND UNCONDITIONAL ACCEPTANCE
+ * OF THOSE TERMS.THIS DRIVER IS PROVIDED "AS IS" AND MENTOR GRAPHICS
+ * MAKES NO WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THIS DRIVER.
+ * MENTOR GRAPHICS SPECIFICALLY DISCLAIMS ALL IMPLIED WARRANTIES
+ * OF MERCHANTABILITY; FITNESS FOR A PARTICULAR PURPOSE AND
+ * NON-INFRINGEMENT.  MENTOR GRAPHICS DOES NOT PROVIDE SUPPORT
+ * SERVICES OR UPDATES FOR THIS DRIVER, EVEN IF YOU ARE A MENTOR
+ * GRAPHICS SUPPORT CUSTOMER.
+ ******************************************************************/
+
+#ifndef __MUSB_HDRC_DEFS_H__
+#define __MUSB_HDRC_DEFS_H__
+
+#include <usb.h>
+#include <usb_defs.h>
+#include <asm/io.h>
+
+#define MUSB_EP0_FIFOSIZE	64	/* This is non-configurable */
+
+/* Mentor USB core register overlay structure */
+struct musb_regs {
+	/* common registers */
+	u8	faddr;
+	u8	power;
+	u16	intrtx;
+	u16	intrrx;
+	u16	intrtxe;
+	u16	intrrxe;
+	u8	intrusb;
+	u8	intrusbe;
+	u16	frame;
+	u8	index;
+	u8	testmode;
+	/* indexed registers */
+	u16	txmaxp;
+	u16	txcsr;
+	u16	rxmaxp;
+	u16	rxcsr;
+	u16	rxcount;
+	u8	txtype;
+	u8	txinterval;
+	u8	rxtype;
+	u8	rxinterval;
+	u8	reserved0;
+	u8	fifosize;
+	/* fifo */
+	u32	fifox[16];
+	/* OTG, dynamic FIFO, version & vendor registers */
+	u8	devctl;
+	u8	reserved1;
+	u8	txfifosz;
+	u8	rxfifosz;
+	u16	txfifoadd;
+	u16	rxfifoadd;
+	u32	vcontrol;
+	u16	hwvers;
+	u16	reserved2[5];
+	u8	epinfo;
+	u8	raminfo;
+	u8	linkinfo;
+	u8	vplen;
+	u8	hseof1;
+	u8	fseof1;
+	u8	lseof1;
+	u8	reserved3;
+	/* target address registers */
+	struct musb_tar_regs {
+		u8	txfuncaddr;
+		u8	reserved0;
+		u8	txhubaddr;
+		u8	txhubport;
+		u8	rxfuncaddr;
+		u8	reserved1;
+		u8	rxhubaddr;
+		u8	rxhubport;
+	} tar[16];
+} __attribute((aligned(32)));
+
+/*
+ * MUSB Register bits
+ */
+
+/* POWER */
+#define MUSB_POWER_ISOUPDATE	0x80
+#define MUSB_POWER_SOFTCONN	0x40
+#define MUSB_POWER_HSENAB	0x20
+#define MUSB_POWER_HSMODE	0x10
+#define MUSB_POWER_RESET	0x08
+#define MUSB_POWER_RESUME	0x04
+#define MUSB_POWER_SUSPENDM	0x02
+#define MUSB_POWER_ENSUSPEND	0x01
+#define MUSB_POWER_HSMODE_SHIFT	4
+
+/* INTRUSB */
+#define MUSB_INTR_SUSPEND	0x01
+#define MUSB_INTR_RESUME	0x02
+#define MUSB_INTR_RESET		0x04
+#define MUSB_INTR_BABBLE	0x04
+#define MUSB_INTR_SOF		0x08
+#define MUSB_INTR_CONNECT	0x10
+#define MUSB_INTR_DISCONNECT	0x20
+#define MUSB_INTR_SESSREQ	0x40
+#define MUSB_INTR_VBUSERROR	0x80	/* For SESSION end */
+
+/* DEVCTL */
+#define MUSB_DEVCTL_BDEVICE	0x80
+#define MUSB_DEVCTL_FSDEV	0x40
+#define MUSB_DEVCTL_LSDEV	0x20
+#define MUSB_DEVCTL_VBUS	0x18
+#define MUSB_DEVCTL_VBUS_SHIFT	3
+#define MUSB_DEVCTL_HM		0x04
+#define MUSB_DEVCTL_HR		0x02
+#define MUSB_DEVCTL_SESSION	0x01
+
+/* TESTMODE */
+#define MUSB_TEST_FORCE_HOST	0x80
+#define MUSB_TEST_FIFO_ACCESS	0x40
+#define MUSB_TEST_FORCE_FS	0x20
+#define MUSB_TEST_FORCE_HS	0x10
+#define MUSB_TEST_PACKET	0x08
+#define MUSB_TEST_K		0x04
+#define MUSB_TEST_J		0x02
+#define MUSB_TEST_SE0_NAK	0x01
+
+/* Allocate for double-packet buffering (effectively doubles assigned _SIZE) */
+#define MUSB_FIFOSZ_DPB		0x10
+/* Allocation size (8, 16, 32, ... 4096) */
+#define MUSB_FIFOSZ_SIZE	0x0f
+
+/* CSR0 */
+#define MUSB_CSR0_FLUSHFIFO	0x0100
+#define MUSB_CSR0_TXPKTRDY	0x0002
+#define MUSB_CSR0_RXPKTRDY	0x0001
+
+/* CSR0 in Peripheral mode */
+#define MUSB_CSR0_P_SVDSETUPEND	0x0080
+#define MUSB_CSR0_P_SVDRXPKTRDY	0x0040
+#define MUSB_CSR0_P_SENDSTALL	0x0020
+#define MUSB_CSR0_P_SETUPEND	0x0010
+#define MUSB_CSR0_P_DATAEND	0x0008
+#define MUSB_CSR0_P_SENTSTALL	0x0004
+
+/* CSR0 in Host mode */
+#define MUSB_CSR0_H_DIS_PING		0x0800
+#define MUSB_CSR0_H_WR_DATATOGGLE	0x0400	/* Set to allow setting: */
+#define MUSB_CSR0_H_DATATOGGLE		0x0200	/* Data toggle control */
+#define MUSB_CSR0_H_NAKTIMEOUT		0x0080
+#define MUSB_CSR0_H_STATUSPKT		0x0040
+#define MUSB_CSR0_H_REQPKT		0x0020
+#define MUSB_CSR0_H_ERROR		0x0010
+#define MUSB_CSR0_H_SETUPPKT		0x0008
+#define MUSB_CSR0_H_RXSTALL		0x0004
+
+/* CSR0 bits to avoid zeroing (write zero clears, write 1 ignored) */
+#define MUSB_CSR0_P_WZC_BITS	\
+	(MUSB_CSR0_P_SENTSTALL)
+#define MUSB_CSR0_H_WZC_BITS	\
+	(MUSB_CSR0_H_NAKTIMEOUT | MUSB_CSR0_H_RXSTALL \
+	| MUSB_CSR0_RXPKTRDY)
+
+/* TxType/RxType */
+#define MUSB_TYPE_SPEED		0xc0
+#define MUSB_TYPE_SPEED_SHIFT	6
+#define MUSB_TYPE_SPEED_HIGH 	1
+#define MUSB_TYPE_SPEED_FULL 	2
+#define MUSB_TYPE_SPEED_LOW	3
+#define MUSB_TYPE_PROTO		0x30	/* Implicitly zero for ep0 */
+#define MUSB_TYPE_PROTO_SHIFT	4
+#define MUSB_TYPE_REMOTE_END	0xf	/* Implicitly zero for ep0 */
+#define MUSB_TYPE_PROTO_BULK 	2
+#define MUSB_TYPE_PROTO_INTR 	3
+
+/* CONFIGDATA */
+#define MUSB_CONFIGDATA_MPRXE		0x80	/* Auto bulk pkt combining */
+#define MUSB_CONFIGDATA_MPTXE		0x40	/* Auto bulk pkt splitting */
+#define MUSB_CONFIGDATA_BIGENDIAN	0x20
+#define MUSB_CONFIGDATA_HBRXE		0x10	/* HB-ISO for RX */
+#define MUSB_CONFIGDATA_HBTXE		0x08	/* HB-ISO for TX */
+#define MUSB_CONFIGDATA_DYNFIFO		0x04	/* Dynamic FIFO sizing */
+#define MUSB_CONFIGDATA_SOFTCONE	0x02	/* SoftConnect */
+#define MUSB_CONFIGDATA_UTMIDW		0x01	/* Data width 0/1 => 8/16bits */
+
+/* TXCSR in Peripheral and Host mode */
+#define MUSB_TXCSR_AUTOSET		0x8000
+#define MUSB_TXCSR_MODE			0x2000
+#define MUSB_TXCSR_DMAENAB		0x1000
+#define MUSB_TXCSR_FRCDATATOG		0x0800
+#define MUSB_TXCSR_DMAMODE		0x0400
+#define MUSB_TXCSR_CLRDATATOG		0x0040
+#define MUSB_TXCSR_FLUSHFIFO		0x0008
+#define MUSB_TXCSR_FIFONOTEMPTY		0x0002
+#define MUSB_TXCSR_TXPKTRDY		0x0001
+
+/* TXCSR in Peripheral mode */
+#define MUSB_TXCSR_P_ISO		0x4000
+#define MUSB_TXCSR_P_INCOMPTX		0x0080
+#define MUSB_TXCSR_P_SENTSTALL		0x0020
+#define MUSB_TXCSR_P_SENDSTALL		0x0010
+#define MUSB_TXCSR_P_UNDERRUN		0x0004
+
+/* TXCSR in Host mode */
+#define MUSB_TXCSR_H_WR_DATATOGGLE	0x0200
+#define MUSB_TXCSR_H_DATATOGGLE		0x0100
+#define MUSB_TXCSR_H_NAKTIMEOUT		0x0080
+#define MUSB_TXCSR_H_RXSTALL		0x0020
+#define MUSB_TXCSR_H_ERROR		0x0004
+#define MUSB_TXCSR_H_DATATOGGLE_SHIFT	8
+
+/* TXCSR bits to avoid zeroing (write zero clears, write 1 ignored) */
+#define MUSB_TXCSR_P_WZC_BITS	\
+	(MUSB_TXCSR_P_INCOMPTX | MUSB_TXCSR_P_SENTSTALL \
+	| MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_FIFONOTEMPTY)
+#define MUSB_TXCSR_H_WZC_BITS	\
+	(MUSB_TXCSR_H_NAKTIMEOUT | MUSB_TXCSR_H_RXSTALL \
+	| MUSB_TXCSR_H_ERROR | MUSB_TXCSR_FIFONOTEMPTY)
+
+/* RXCSR in Peripheral and Host mode */
+#define MUSB_RXCSR_AUTOCLEAR		0x8000
+#define MUSB_RXCSR_DMAENAB		0x2000
+#define MUSB_RXCSR_DISNYET		0x1000
+#define MUSB_RXCSR_PID_ERR		0x1000
+#define MUSB_RXCSR_DMAMODE		0x0800
+#define MUSB_RXCSR_INCOMPRX		0x0100
+#define MUSB_RXCSR_CLRDATATOG		0x0080
+#define MUSB_RXCSR_FLUSHFIFO		0x0010
+#define MUSB_RXCSR_DATAERROR		0x0008
+#define MUSB_RXCSR_FIFOFULL		0x0002
+#define MUSB_RXCSR_RXPKTRDY		0x0001
+
+/* RXCSR in Peripheral mode */
+#define MUSB_RXCSR_P_ISO		0x4000
+#define MUSB_RXCSR_P_SENTSTALL		0x0040
+#define MUSB_RXCSR_P_SENDSTALL		0x0020
+#define MUSB_RXCSR_P_OVERRUN		0x0004
+
+/* RXCSR in Host mode */
+#define MUSB_RXCSR_H_AUTOREQ		0x4000
+#define MUSB_RXCSR_H_WR_DATATOGGLE	0x0400
+#define MUSB_RXCSR_H_DATATOGGLE		0x0200
+#define MUSB_RXCSR_H_RXSTALL		0x0040
+#define MUSB_RXCSR_H_REQPKT		0x0020
+#define MUSB_RXCSR_H_ERROR		0x0004
+#define MUSB_S_RXCSR_H_DATATOGGLE	9
+
+/* RXCSR bits to avoid zeroing (write zero clears, write 1 ignored) */
+#define MUSB_RXCSR_P_WZC_BITS	\
+	(MUSB_RXCSR_P_SENTSTALL | MUSB_RXCSR_P_OVERRUN \
+	| MUSB_RXCSR_RXPKTRDY)
+#define MUSB_RXCSR_H_WZC_BITS	\
+	(MUSB_RXCSR_H_RXSTALL | MUSB_RXCSR_H_ERROR \
+	| MUSB_RXCSR_DATAERROR | MUSB_RXCSR_RXPKTRDY)
+
+/* HUBADDR */
+#define MUSB_HUBADDR_MULTI_TT		0x80
+
+/* Endpoint configuration information. Note: The value of endpoint fifo size
+ * element should be either 8,16,32,64,128,256,512,1024,2048 or 4096. Other
+ * values are not supported
+ */
+struct musb_epinfo {
+	u8	epnum;	/* endpoint number 	*/
+	u8	epdir;	/* endpoint direction	*/
+	u16	epsize;	/* endpoint FIFO size	*/
+};
+
+/*
+ * Platform specific MUSB configuration. Any platform using the musb
+ * functionality should create one instance of this structure in the
+ * platform specific file.
+ */
+struct musb_config {
+	struct	musb_regs	*regs;
+	u32			timeout;
+	u8			musb_speed;
+};
+
+/* externally defined data */
+extern struct musb_config	musb_cfg;
+extern struct musb_regs		*musbr;
+
+/* exported functions */
+extern void musb_start(void);
+extern void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt);
+extern void write_fifo(u8 ep, u32 length, void *fifo_data);
+extern void read_fifo(u8 ep, u32 length, void *fifo_data);
+
+/* extern functions */
+extern inline void musb_writew(u32 offset, u16 value);
+extern inline void musb_writeb(u32 offset, u8 value);
+extern inline u16 musb_readw(u32 offset);
+extern inline u8 musb_readb(u32 offset);
+
+#endif	/* __MUSB_HDRC_DEFS_H__ */
+
diff --git a/drivers/usb/musb_hcd.c b/drivers/usb/musb_hcd.c
new file mode 100644
index 0000000..352a0d4
--- /dev/null
+++ b/drivers/usb/musb_hcd.c
@@ -0,0 +1,792 @@
+/*
+ * Mentor USB OTG Core host controller driver.
+ *
+ * Copyright (c) 2008 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Author: Thomas Abraham t-abraham@ti.com, Texas Instruments
+ */
+
+#include <common.h>
+#include "musb_hcd.h"
+
+/* MSC control transfers */
+#define USB_MSC_BBB_RESET 	0xFF
+#define USB_MSC_BBB_GET_MAX_LUN	0xFE
+
+/* Endpoint configuration information */
+static struct musb_epinfo epinfo[3] = {
+	{MUSB_BULK_EP, 1, 512}, /* EP1 - Bluk Out - 512 Bytes */
+	{MUSB_BULK_EP, 0, 512}, /* EP1 - Bluk In  - 512 Bytes */
+	{MUSB_INTR_EP, 0, 64}   /* EP2 - Interrupt IN - 64 Bytes */
+};
+
+/*
+ * This function writes the data toggle value.
+ */
+static void write_toggle(struct usb_device *dev, u8 ep, u8 dir_out)
+{
+	u16 toggle = usb_gettoggle(dev, ep, dir_out);
+	u16 csr;
+
+	if (dir_out) {
+		if (!toggle)
+			writew(MUSB_TXCSR_CLRDATATOG, &musbr->txcsr);
+		else {
+			csr = readw(&musbr->txcsr);
+			csr |= MUSB_TXCSR_H_WR_DATATOGGLE;
+			writew(csr, &musbr->txcsr);
+			csr |= (toggle << MUSB_TXCSR_H_DATATOGGLE_SHIFT);
+			writew(csr, &musbr->txcsr);
+		}
+	} else {
+		if (!toggle)
+			writew(MUSB_RXCSR_CLRDATATOG, &musbr->rxcsr);
+		else {
+			csr = readw(&musbr->rxcsr);
+			csr |= MUSB_RXCSR_H_WR_DATATOGGLE;
+			writew(csr, &musbr->rxcsr);
+			csr |= (toggle << MUSB_S_RXCSR_H_DATATOGGLE);
+			writew(csr, &musbr->rxcsr);
+		}
+	}
+}
+
+/*
+ * This function checks if RxStall has occured on the endpoint. If a RxStall
+ * has occured, the RxStall is cleared and 1 is returned. If RxStall has
+ * not occured, 0 is returned.
+ */
+static u8 check_stall(u8 ep, u8 dir_out)
+{
+	u16 csr;
+
+	/* For endpoint 0 */
+	if (!ep) {
+		csr = readw(&musbr->txcsr);
+		if (csr & MUSB_CSR0_H_RXSTALL) {
+			csr &= ~MUSB_CSR0_H_RXSTALL;
+			writew(csr, &musbr->txcsr);
+			return 1;
+		}
+	} else { /* For non-ep0 */
+		if (dir_out) { /* is it tx ep */
+			csr = readw(&musbr->txcsr);
+			if (csr & MUSB_TXCSR_H_RXSTALL) {
+				csr &= ~MUSB_TXCSR_H_RXSTALL;
+				writew(csr, &musbr->txcsr);
+				return 1;
+			}
+		} else { /* is it rx ep */
+			csr = readw(&musbr->rxcsr);
+			if (csr & MUSB_RXCSR_H_RXSTALL) {
+				csr &= ~MUSB_RXCSR_H_RXSTALL;
+				writew(csr, &musbr->rxcsr);
+				return 1;
+			}
+		}
+	}
+	return 0;
+}
+
+/*
+ * waits until ep0 is ready. Returns 0 if ep is ready, -1 for timeout
+ * error and -2 for stall.
+ */
+static int wait_until_ep0_ready(struct usb_device *dev, u32 bit_mask)
+{
+	u16 csr;
+	int result = 1;
+
+	while (result > 0) {
+		csr = readw(&musbr->txcsr);
+		if (csr & MUSB_CSR0_H_ERROR) {
+			csr &= ~MUSB_CSR0_H_ERROR;
+			writew(csr, &musbr->txcsr);
+			dev->status = USB_ST_CRC_ERR;
+			result = -1;
+			break;
+		}
+
+		switch (bit_mask) {
+		case MUSB_CSR0_TXPKTRDY:
+			if (!(csr & MUSB_CSR0_TXPKTRDY)) {
+				if (check_stall(MUSB_CONTROL_EP, 0)) {
+					dev->status = USB_ST_STALLED;
+					result = -2;
+				} else
+					result = 0;
+			}
+			break;
+
+		case MUSB_CSR0_RXPKTRDY:
+			if (check_stall(MUSB_CONTROL_EP, 0)) {
+				dev->status = USB_ST_STALLED;
+				result = -2;
+			} else
+				if (csr & MUSB_CSR0_RXPKTRDY)
+					result = 0;
+			break;
+
+		case MUSB_CSR0_H_REQPKT:
+			if (!(csr & MUSB_CSR0_H_REQPKT)) {
+				if (check_stall(MUSB_CONTROL_EP, 0)) {
+					dev->status = USB_ST_STALLED;
+					result = -2;
+				} else
+					result = 0;
+			}
+			break;
+		}
+	}
+	return result;
+}
+
+/*
+ * waits until tx ep is ready. Returns 1 when ep is ready and 0 on error.
+ */
+static u8 wait_until_txep_ready(struct usb_device *dev, u8 ep)
+{
+	u16 csr;
+
+	do {
+		if (check_stall(ep, 1)) {
+			dev->status = USB_ST_STALLED;
+			return 0;
+		}
+
+		csr = readw(&musbr->txcsr);
+		if (csr & MUSB_TXCSR_H_ERROR) {
+			dev->status = USB_ST_CRC_ERR;
+			return 0;
+		}
+	} while (csr & MUSB_TXCSR_TXPKTRDY);
+	return 1;
+}
+
+/*
+ * waits until rx ep is ready. Returns 1 when ep is ready and 0 on error.
+ */
+static u8 wait_until_rxep_ready(struct usb_device *dev, u8 ep)
+{
+	u16 csr;
+
+	do {
+		if (check_stall(ep, 0)) {
+			dev->status = USB_ST_STALLED;
+			return 0;
+		}
+
+		csr = readw(&musbr->rxcsr);
+		if (csr & MUSB_RXCSR_H_ERROR) {
+			dev->status = USB_ST_CRC_ERR;
+			return 0;
+		}
+	} while (!(csr & MUSB_RXCSR_RXPKTRDY));
+	return 1;
+}
+
+/*
+ * This function performs the setup phase of the control transfer
+ */
+static int ctrlreq_setup_phase(struct usb_device *dev, struct devrequest *setup)
+{
+	int result;
+	u16 csr;
+
+	/* write the control request to ep0 fifo */
+	write_fifo(MUSB_CONTROL_EP, sizeof(struct devrequest), (void *)setup);
+
+	/* enable transfer of setup packet */
+	csr = readw(&musbr->txcsr);
+	csr |= (MUSB_CSR0_TXPKTRDY|MUSB_CSR0_H_SETUPPKT);
+	writew(csr, &musbr->txcsr);
+
+	/* wait until the setup packet is transmitted */
+	result = wait_until_ep0_ready(dev, MUSB_CSR0_TXPKTRDY);
+	dev->act_len = 0;
+	return result;
+}
+
+/*
+ * This function handles the control transfer in data phase
+ */
+static int ctrlreq_in_data_phase(struct usb_device *dev, u32 len, void *buffer)
+{
+	u16 csr;
+	u32 rxlen = 0;
+	u32 nextlen = 0;
+	u8  maxpktsize = (1 << dev->maxpacketsize) * 8;
+	u8  *rxbuff = (u8 *)buffer;
+	u8  rxedlength;
+	int result;
+
+	while (rxlen < len) {
+		/* Determine the next read length */
+		nextlen = ((len-rxlen) > maxpktsize) ? maxpktsize : (len-rxlen);
+
+		/* Set the ReqPkt bit */
+		csr = readw(&musbr->txcsr);
+		writew(csr | MUSB_CSR0_H_REQPKT, &musbr->txcsr);
+		result = wait_until_ep0_ready(dev, MUSB_CSR0_RXPKTRDY);
+		if (result < 0)
+			return result;
+
+		/* Actual number of bytes received by usb */
+		rxedlength = readb(&musbr->rxcount);
+
+		/* Read the data from the RxFIFO */
+		read_fifo(MUSB_CONTROL_EP, rxedlength, &rxbuff[rxlen]);
+
+		/* Clear the RxPktRdy Bit */
+		csr = readw(&musbr->txcsr);
+		csr &= ~MUSB_CSR0_RXPKTRDY;
+		writew(csr, &musbr->txcsr);
+
+		/* short packet? */
+		if (rxedlength != nextlen) {
+			dev->act_len += rxedlength;
+			break;
+		}
+		rxlen += nextlen;
+		dev->act_len = rxlen;
+	}
+	return 0;
+}
+
+/*
+ * This function handles the control transfer out data phase
+ */
+static int ctrlreq_out_data_phase(struct usb_device *dev, u32 len, void *buffer)
+{
+	u16 csr;
+	u32 txlen = 0;
+	u32 nextlen = 0;
+	u8  maxpktsize = (1 << dev->maxpacketsize) * 8;
+	u8  *txbuff = (u8 *)buffer;
+	int result = 0;
+
+	while (txlen < len) {
+		/* Determine the next write length */
+		nextlen = ((len-txlen) > maxpktsize) ? maxpktsize : (len-txlen);
+
+		/* Load the data to send in FIFO */
+		write_fifo(MUSB_CONTROL_EP, txlen, &txbuff[txlen]);
+
+		/* Set TXPKTRDY bit */
+		csr = readw(&musbr->txcsr);
+		writew(csr | MUSB_CSR0_H_DIS_PING | MUSB_CSR0_TXPKTRDY,
+					&musbr->txcsr);
+		result = wait_until_ep0_ready(dev, MUSB_CSR0_TXPKTRDY);
+		if (result < 0)
+			break;
+
+		txlen += nextlen;
+		dev->act_len = txlen;
+	}
+	return result;
+}
+
+/*
+ * This function handles the control transfer out status phase
+ */
+static int ctrlreq_out_status_phase(struct usb_device *dev)
+{
+	u16 csr;
+	int result;
+
+	/* Set the StatusPkt bit */
+	csr = readw(&musbr->txcsr);
+	csr |= (MUSB_CSR0_H_DIS_PING | MUSB_CSR0_TXPKTRDY |
+			MUSB_CSR0_H_STATUSPKT);
+	writew(csr, &musbr->txcsr);
+
+	/* Wait until TXPKTRDY bit is cleared */
+	result = wait_until_ep0_ready(dev, MUSB_CSR0_TXPKTRDY);
+	return result;
+}
+
+/*
+ * This function handles the control transfer in status phase
+ */
+static int ctrlreq_in_status_phase(struct usb_device *dev)
+{
+	u16 csr;
+	int result;
+
+	/* Set the StatusPkt bit and ReqPkt bit */
+	csr = MUSB_CSR0_H_DIS_PING | MUSB_CSR0_H_REQPKT | MUSB_CSR0_H_STATUSPKT;
+	writew(csr, &musbr->txcsr);
+	result = wait_until_ep0_ready(dev, MUSB_CSR0_H_REQPKT);
+
+	/* clear StatusPkt bit and RxPktRdy bit */
+	csr = readw(&musbr->txcsr);
+	csr &= ~(MUSB_CSR0_RXPKTRDY | MUSB_CSR0_H_STATUSPKT);
+	writew(csr, &musbr->txcsr);
+	return result;
+}
+
+/*
+ * determines the speed of the device (High/Full/Slow)
+ */
+static u8 get_dev_speed(struct usb_device *dev)
+{
+	return (dev->speed & USB_SPEED_HIGH) ? MUSB_TYPE_SPEED_HIGH :
+		((dev->speed & USB_SPEED_LOW) ? MUSB_TYPE_SPEED_LOW :
+						MUSB_TYPE_SPEED_FULL);
+}
+
+/*
+ * configure the hub address and the port address.
+ */
+static void config_hub_port(struct usb_device *dev, u8 ep)
+{
+	u8 chid;
+	u8 hub;
+
+	/* Find out the nearest parent which is high speed */
+	while (dev->parent->parent != NULL)
+		if (get_dev_speed(dev->parent) !=  MUSB_TYPE_SPEED_HIGH)
+			dev = dev->parent;
+		else
+			break;
+
+	/* determine the port address at that hub */
+	hub = dev->parent->devnum;
+	for (chid = 0; chid < USB_MAXCHILDREN; chid++)
+		if (dev->parent->children[chid] == dev)
+			break;
+
+	/* configure the hub address and the port address */
+	writeb(hub, &musbr->tar[ep].txhubaddr);
+	writeb((chid + 1), &musbr->tar[ep].txhubport);
+	writeb(hub, &musbr->tar[ep].rxhubaddr);
+	writeb((chid + 1), &musbr->tar[ep].rxhubport);
+}
+
+/*
+ * do a control transfer
+ */
+int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
+			int len, struct devrequest *setup)
+{
+	int devnum = usb_pipedevice(pipe);
+	u16 csr;
+	u8  devspeed;
+
+	/* select control endpoint */
+	writeb(MUSB_CONTROL_EP, &musbr->index);
+	csr = readw(&musbr->txcsr);
+
+	/* target addr and (for multipoint) hub addr/port */
+	writeb(devnum, &musbr->tar[MUSB_CONTROL_EP].txfuncaddr);
+	writeb(devnum, &musbr->tar[MUSB_CONTROL_EP].rxfuncaddr);
+
+	/* configure the hub address and the port number as required */
+	devspeed = get_dev_speed(dev);
+	if ((musb_ishighspeed()) && (dev->parent != NULL) &&
+		(devspeed != MUSB_TYPE_SPEED_HIGH)) {
+		config_hub_port(dev, MUSB_CONTROL_EP);
+		writeb(devspeed << 6, &musbr->txtype);
+	} else {
+		writeb(musb_cfg.musb_speed << 6, &musbr->txtype);
+		writeb(0, &musbr->tar[MUSB_CONTROL_EP].txhubaddr);
+		writeb(0, &musbr->tar[MUSB_CONTROL_EP].txhubport);
+		writeb(0, &musbr->tar[MUSB_CONTROL_EP].rxhubaddr);
+		writeb(0, &musbr->tar[MUSB_CONTROL_EP].rxhubport);
+	}
+
+	/* Control transfer setup phase */
+	if (ctrlreq_setup_phase(dev, setup) < 0)
+		return 0;
+
+	switch (setup->request) {
+	case USB_REQ_GET_DESCRIPTOR:
+	case USB_REQ_GET_CONFIGURATION:
+	case USB_REQ_GET_INTERFACE:
+	case USB_REQ_GET_STATUS:
+	case USB_MSC_BBB_GET_MAX_LUN:
+		/* control transfer in-data-phase */
+		if (ctrlreq_in_data_phase(dev, len, buffer) < 0)
+			return 0;
+		/* control transfer out-status-phase */
+		if (ctrlreq_out_status_phase(dev) < 0)
+			return 0;
+		break;
+
+	case USB_REQ_SET_ADDRESS:
+	case USB_REQ_SET_CONFIGURATION:
+	case USB_REQ_SET_FEATURE:
+	case USB_REQ_SET_INTERFACE:
+	case USB_REQ_CLEAR_FEATURE:
+	case USB_MSC_BBB_RESET:
+		/* control transfer in status phase */
+		if (ctrlreq_in_status_phase(dev) < 0)
+			return 0;
+		break;
+
+	case USB_REQ_SET_DESCRIPTOR:
+		/* control transfer out data phase */
+		if (ctrlreq_out_data_phase(dev, len, buffer) < 0)
+			return 0;
+		/* control transfer in status phase */
+		if (ctrlreq_in_status_phase(dev) < 0)
+			return 0;
+		break;
+
+	default:
+		/* unhandled control transfer */
+		return -1;
+	}
+
+	dev->status = 0;
+	dev->act_len = len;
+	return len;
+}
+
+/*
+ * do a bulk transfer
+ */
+int submit_bulk_msg(struct usb_device *dev, unsigned long pipe,
+					void *buffer, int len)
+{
+	int dir_out = usb_pipeout(pipe);
+	int ep = usb_pipeendpoint(pipe);
+	int devnum = usb_pipedevice(pipe);
+	u8  type;
+	u16 csr;
+	u32 txlen = 0;
+	u32 nextlen = 0;
+	u8  devspeed;
+
+	/* select bulk endpoint */
+	writeb(MUSB_BULK_EP, &musbr->index);
+
+	/* write the address of the device */
+	if (dir_out)
+		writeb(devnum, &musbr->tar[MUSB_BULK_EP].txfuncaddr);
+	else
+		writeb(devnum, &musbr->tar[MUSB_BULK_EP].rxfuncaddr);
+
+	/* configure the hub address and the port number as required */
+	devspeed = get_dev_speed(dev);
+	if ((musb_ishighspeed()) && (dev->parent != NULL) &&
+		(devspeed != MUSB_TYPE_SPEED_HIGH)) {
+		/*
+		 * MUSB is in high speed and the destination device is full
+		 * speed device. So configure the hub address and port
+		 * address registers.
+		 */
+		config_hub_port(dev, MUSB_BULK_EP);
+	} else {
+		if (dir_out) {
+			writeb(0, &musbr->tar[MUSB_BULK_EP].txhubaddr);
+			writeb(0, &musbr->tar[MUSB_BULK_EP].txhubport);
+		} else {
+			writeb(0, &musbr->tar[MUSB_BULK_EP].rxhubaddr);
+			writeb(0, &musbr->tar[MUSB_BULK_EP].rxhubport);
+		}
+		devspeed = musb_cfg.musb_speed;
+	}
+
+	/* Write the saved toggle bit value */
+	write_toggle(dev, ep, dir_out);
+
+	if (dir_out) { /* bulk-out transfer */
+		/* Program the TxType register */
+		type = (devspeed << MUSB_TYPE_SPEED_SHIFT) |
+			   (MUSB_TYPE_PROTO_BULK << MUSB_TYPE_PROTO_SHIFT) |
+			   (ep & MUSB_TYPE_REMOTE_END);
+		writeb(type, &musbr->txtype);
+
+		/* Write maximum packet size to the TxMaxp register */
+		writew(dev->epmaxpacketout[ep], &musbr->txmaxp);
+		while (txlen < len) {
+			nextlen = ((len-txlen) < dev->epmaxpacketout[ep]) ?
+					(len-txlen) : dev->epmaxpacketout[ep];
+
+			/* Write the data to the FIFO */
+			write_fifo(MUSB_BULK_EP, nextlen,
+					(void *)(((u8 *)buffer) + txlen));
+
+			/* Set the TxPktRdy bit */
+			csr = readw(&musbr->txcsr);
+			writew(csr | MUSB_TXCSR_TXPKTRDY, &musbr->txcsr);
+
+			/* Wait until the TxPktRdy bit is cleared */
+			if (!wait_until_txep_ready(dev, MUSB_BULK_EP)) {
+				readw(&musbr->txcsr);
+				usb_settoggle(dev, ep, dir_out,
+				(csr >> MUSB_TXCSR_H_DATATOGGLE_SHIFT) & 1);
+				dev->act_len = txlen;
+				return 0;
+			}
+			txlen += nextlen;
+		}
+
+		/* Keep a copy of the data toggle bit */
+		csr = readw(&musbr->txcsr);
+		usb_settoggle(dev, ep, dir_out,
+				(csr >> MUSB_TXCSR_H_DATATOGGLE_SHIFT) & 1);
+	} else { /* bulk-in transfer */
+		/* Write the saved toggle bit value */
+		write_toggle(dev, ep, dir_out);
+
+		/* Program the RxType register */
+		type = (devspeed << MUSB_TYPE_SPEED_SHIFT) |
+			   (MUSB_TYPE_PROTO_BULK << MUSB_TYPE_PROTO_SHIFT) |
+			   (ep & MUSB_TYPE_REMOTE_END);
+		writeb(type, &musbr->rxtype);
+
+		/* Write the maximum packet size to the RxMaxp register */
+		writew(dev->epmaxpacketin[ep], &musbr->rxmaxp);
+		while (txlen < len) {
+			nextlen = ((len-txlen) < dev->epmaxpacketin[ep]) ?
+					(len-txlen) : dev->epmaxpacketin[ep];
+
+			/* Set the ReqPkt bit */
+			writew(MUSB_RXCSR_H_REQPKT, &musbr->rxcsr);
+
+			/* Wait until the RxPktRdy bit is set */
+			if (!wait_until_rxep_ready(dev, MUSB_BULK_EP)) {
+				csr = readw(&musbr->rxcsr);
+				usb_settoggle(dev, ep, dir_out,
+				(csr >> MUSB_S_RXCSR_H_DATATOGGLE) & 1);
+				csr &= ~MUSB_RXCSR_RXPKTRDY;
+				writew(csr, &musbr->rxcsr);
+				dev->act_len = txlen;
+				return 0;
+			}
+
+			/* Read the data from the FIFO */
+			read_fifo(MUSB_BULK_EP, nextlen,
+					(void *)(((u8 *)buffer) + txlen));
+
+			/* Clear the RxPktRdy bit */
+			csr =  readw(&musbr->rxcsr);
+			csr &= ~MUSB_RXCSR_RXPKTRDY;
+			writew(csr, &musbr->rxcsr);
+			txlen += nextlen;
+		}
+
+		/* Keep a copy of the data toggle bit */
+		csr = readw(&musbr->rxcsr);
+		usb_settoggle(dev, ep, dir_out,
+				(csr >> MUSB_S_RXCSR_H_DATATOGGLE) & 1);
+	}
+
+	/* bulk transfer is complete */
+	dev->status = 0;
+	dev->act_len = len;
+	return 0;
+}
+
+/*
+ * This function initializes the usb controller module.
+ */
+int usb_lowlevel_init(void)
+{
+	u8  power;
+	u32 timeout;
+
+	if (musb_platform_init() == -1)
+		return -1;
+
+	/* Configure all the endpoint FIFO's and start usb controller */
+	musbr = musb_cfg.regs;
+	musb_configure_ep(&epinfo[0],
+			sizeof(epinfo) / sizeof(struct musb_epinfo));
+	musb_start();
+
+	/*
+	 * Wait until musb is enabled in host mode with a timeout. There
+	 * should be a usb device connected.
+	 */
+	timeout = musb_cfg.timeout;
+	while (timeout--)
+		if (readb(&musbr->devctl) & MUSB_DEVCTL_HM)
+			break;
+
+	/* if musb core is not in host mode, then return */
+	if (!timeout)
+		return -1;
+
+	/* start usb bus reset */
+	power = readb(&musbr->power);
+	writeb(power | MUSB_POWER_RESET, &musbr->power);
+
+	/* After initiating a usb reset, wait for about 20ms to 30ms */
+	udelay(30000);
+
+	/* stop usb bus reset */
+	power = readb(&musbr->power);
+	power &= ~MUSB_POWER_RESET;
+	writeb(power, &musbr->power);
+
+	/* Determine if the connected device is a high/full/low speed device */
+	musb_cfg.musb_speed = (readb(&musbr->power) & MUSB_POWER_HSMODE) ?
+			MUSB_TYPE_SPEED_HIGH :
+			((readb(&musbr->devctl) & MUSB_DEVCTL_FSDEV) ?
+			MUSB_TYPE_SPEED_FULL : MUSB_TYPE_SPEED_LOW);
+	return 0;
+}
+
+/*
+ * This function stops the operation of the davinci usb module.
+ */
+int usb_lowlevel_stop(void)
+{
+	/* Reset the USB module */
+	musb_platform_deinit();
+	writeb(0, &musbr->devctl);
+	return 0;
+}
+
+/*
+ * This function supports usb interrupt transfers. Currently, usb interrupt
+ * transfers are not supported.
+ */
+int submit_int_msg(struct usb_device *dev, unsigned long pipe,
+				void *buffer, int len, int interval)
+{
+	int dir_out = usb_pipeout(pipe);
+	int ep = usb_pipeendpoint(pipe);
+	int devnum = usb_pipedevice(pipe);
+	u8  type;
+	u16 csr;
+	u32 txlen = 0;
+	u32 nextlen = 0;
+	u8  devspeed;
+
+	/* select interrupt endpoint */
+	writeb(MUSB_INTR_EP, &musbr->index);
+
+	/* write the address of the device */
+	if (dir_out)
+		writeb(devnum, &musbr->tar[MUSB_INTR_EP].txfuncaddr);
+	else
+		writeb(devnum, &musbr->tar[MUSB_INTR_EP].rxfuncaddr);
+
+	/* configure the hub address and the port number as required */
+	devspeed = get_dev_speed(dev);
+	if ((musb_ishighspeed()) && (dev->parent != NULL) &&
+		(devspeed != MUSB_TYPE_SPEED_HIGH)) {
+		/*
+		 * MUSB is in high speed and the destination device is full
+		 * speed device. So configure the hub address and port
+		 * address registers.
+		 */
+		config_hub_port(dev, MUSB_INTR_EP);
+	} else {
+		if (dir_out) {
+			writeb(0, &musbr->tar[MUSB_INTR_EP].txhubaddr);
+			writeb(0, &musbr->tar[MUSB_INTR_EP].txhubport);
+		} else {
+			writeb(0, &musbr->tar[MUSB_INTR_EP].rxhubaddr);
+			writeb(0, &musbr->tar[MUSB_INTR_EP].rxhubport);
+		}
+		devspeed = musb_cfg.musb_speed;
+	}
+
+	/* Write the saved toggle bit value */
+	write_toggle(dev, ep, dir_out);
+
+	if (!dir_out) { /* intrrupt-in transfer */
+		/* Write the saved toggle bit value */
+		write_toggle(dev, ep, dir_out);
+		writeb(interval, &musbr->rxinterval);
+
+		/* Program the RxType register */
+		type = (devspeed << MUSB_TYPE_SPEED_SHIFT) |
+			   (MUSB_TYPE_PROTO_INTR << MUSB_TYPE_PROTO_SHIFT) |
+			   (ep & MUSB_TYPE_REMOTE_END);
+		writeb(type, &musbr->rxtype);
+
+		/* Write the maximum packet size to the RxMaxp register */
+		writew(dev->epmaxpacketin[ep], &musbr->rxmaxp);
+
+		while (txlen < len) {
+			nextlen = ((len-txlen) < dev->epmaxpacketin[ep]) ?
+					(len-txlen) : dev->epmaxpacketin[ep];
+
+			/* Set the ReqPkt bit */
+			writew(MUSB_RXCSR_H_REQPKT, &musbr->rxcsr);
+
+			/* Wait until the RxPktRdy bit is set */
+			if (!wait_until_rxep_ready(dev, MUSB_INTR_EP)) {
+				csr = readw(&musbr->rxcsr);
+				usb_settoggle(dev, ep, dir_out,
+				(csr >> MUSB_S_RXCSR_H_DATATOGGLE) & 1);
+				csr &= ~MUSB_RXCSR_RXPKTRDY;
+				writew(csr, &musbr->rxcsr);
+				dev->act_len = txlen;
+				return 0;
+			}
+
+			/* Read the data from the FIFO */
+			read_fifo(MUSB_INTR_EP, nextlen,
+					(void *)(((u8 *)buffer) + txlen));
+
+			/* Clear the RxPktRdy bit */
+			csr =  readw(&musbr->rxcsr);
+			csr &= ~MUSB_RXCSR_RXPKTRDY;
+			writew(csr, &musbr->rxcsr);
+			txlen += nextlen;
+		}
+
+		/* Keep a copy of the data toggle bit */
+		csr = readw(&musbr->rxcsr);
+		usb_settoggle(dev, ep, dir_out,
+				(csr >> MUSB_S_RXCSR_H_DATATOGGLE) & 1);
+	}
+
+	/* interrupt transfer is complete */
+	dev->irq_status = 0;
+	dev->irq_act_len = len;
+	dev->irq_handle(dev);
+	dev->status = 0;
+	dev->act_len = len;
+	return 0;
+}
+
+
+#ifdef CONFIG_SYS_USB_EVENT_POLL
+/*
+ * This function polls for USB keyboard data.
+ */
+void usb_event_poll()
+{
+	device_t *dev;
+	struct usb_device *usb_kbd_dev;
+	struct usb_interface_descriptor *iface;
+	struct usb_endpoint_descriptor *ep;
+	int pipe;
+	int maxp;
+
+	/* Get the pointer to USB Keyboard device pointer */
+	dev = device_get_by_name("usbkbd");
+	usb_kbd_dev = (struct usb_device *)dev->priv;
+	iface = &usb_kbd_dev->config.if_desc[0];
+	ep = &iface->ep_desc[0];
+	pipe = usb_rcvintpipe(usb_kbd_dev, ep->bEndpointAddress);
+
+	/* Submit a interrupt transfer request */
+	maxp = usb_maxpacket(usb_kbd_dev, pipe);
+	usb_submit_int_msg(usb_kbd_dev, pipe, &new[0],
+			maxp > 8 ? 8 : maxp, ep->bInterval);
+}
+#endif /* CONFIG_SYS_USB_EVENT_POLL */
diff --git a/drivers/usb/musb_hcd.h b/drivers/usb/musb_hcd.h
new file mode 100644
index 0000000..bb83311
--- /dev/null
+++ b/drivers/usb/musb_hcd.h
@@ -0,0 +1,51 @@
+/*
+ * Mentor USB OTG Core host controller driver.
+ *
+ * Copyright (c) 2008 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Author: Thomas Abraham t-abraham@ti.com, Texas Instruments
+ */
+
+#ifndef __MUSB_HCD_H__
+#define __MUSB_HCD_H__
+
+#include "musb_core.h"
+#ifdef CONFIG_USB_KEYBOARD
+#include <devices.h>
+extern unsigned char new[];
+#endif
+
+/* This defines the endpoint number used for control transfers */
+#define MUSB_CONTROL_EP 0
+
+/* This defines the endpoint number used for bulk transfer */
+#define MUSB_BULK_EP 1
+
+/* This defines the endpoint number used for interrupt transfer */
+#define MUSB_INTR_EP 2
+
+/* Determine the operating speed of MUSB core */
+#define musb_ishighspeed() \
+	((readb(&musbr->power) & MUSB_POWER_HSMODE) \
+		>> MUSB_POWER_HSMODE_SHIFT)
+
+/* extern functions */
+extern int musb_platform_init(void);
+extern void musb_platform_deinit(void);
+
+#endif	/* __MUSB_HCD_H__ */