Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
diff --git a/doc/README.m68k b/doc/README.m68k
index c85febc..9d5c08f 100644
--- a/doc/README.m68k
+++ b/doc/README.m68k
@@ -17,7 +17,7 @@
Bernhard Kuhn ported U-Boot 0.4.0 to the Motorola Coldfire
architecture. The patches of Bernhard support the MCF5272 and
MCF5282. A great disadvantage of these patches was that they needed
-a pre-bootloader to start u-boot. Because of this, a new port was
+a pre-bootloader to start U-Boot. Because of this, a new port was
created which no longer needs a first stage booter.
Although this port is intended to cover all M68k processors, only
@@ -53,8 +53,8 @@
U-Boot Memory Map:
------------------
-0xffe00000 - 0xffe3ffff u-boot
-0xffe04000 - 0xffe05fff environment (embedded in u-boot!)
+0xffe00000 - 0xffe3ffff U-Boot
+0xffe04000 - 0xffe05fff environment (embedded in U-Boot!)
0xffe40000 - 0xffffffff free for linux/applications
@@ -65,13 +65,13 @@
To configure the board, type: make M5272C3_config
At the moment the code isn't fully implemented and still needs a pre-loader!
-The preloader must initialize the processor and then start u-boot. The board
+The preloader must initialize the processor and then start U-Boot. The board
must be configured for a pre-loader (see 4.1)
For the preloader, please see
http://mailman.uclinux.org/pipermail/uclinux-dev/2003-December/023384.html
-U-boot is configured to run at 0x20000 at default. This can be configured by
+U-Boot is configured to run at 0x20000 at default. This can be configured by
change CONFIG_SYS_TEXT_BASE in board/m5282evb/config.mk and CONFIG_SYS_MONITOR_BASE in
include/configs/M5282EVB.h.
@@ -91,10 +91,10 @@
4.1 Configuration to use a pre-loader
-------------------------------------
-If u-boot should be loaded to RAM and started by a pre-loader
+If U-Boot should be loaded to RAM and started by a pre-loader
CONFIG_MONITOR_IS_IN_RAM must be defined. If it is defined the
initial vector table and basic processor initialization will not
-be compiled in. The start address of u-boot must be adjusted in
+be compiled in. The start address of U-Boot must be adjusted in
the boards config header file (CONFIG_SYS_MONITOR_BASE) and Makefile
(CONFIG_SYS_TEXT_BASE) to the load address.
@@ -105,7 +105,7 @@
CONFIG_M5272 -- defined for all Motorola MCF5272 CPUs
CONFIG_MONITOR_IS_IN_RAM
- -- defined if u-boot is loaded by a pre-loader
+ -- defined if U-Boot is loaded by a pre-loader
CONFIG_SYS_MBAR -- defines the base address of the MCF5272 configuration registers
CONFIG_SYS_INIT_RAM_ADDR
@@ -130,7 +130,7 @@
CONFIG_M5282 -- defined for all Motorola MCF5282 CPUs
CONFIG_MONITOR_IS_IN_RAM
- -- defined if u-boot is loaded by a pre-loader
+ -- defined if U-Boot is loaded by a pre-loader
CONFIG_SYS_MBAR -- defines the base address of the MCF5282 internal register space
CONFIG_SYS_INIT_RAM_ADDR