board: traverse: add initial Ten64 support
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
diff --git a/configs/ten64_tfa_defconfig b/configs/ten64_tfa_defconfig
new file mode 100644
index 0000000..8d45b13
--- /dev/null
+++ b/configs/ten64_tfa_defconfig
@@ -0,0 +1,119 @@
+CONFIG_ARM=y
+CONFIG_TARGET_TEN64=y
+CONFIG_SYS_TEXT_BASE=0x82000000
+CONFIG_QSPI_AHB_INIT=y
+CONFIG_TFABOOT=y
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=2
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_FDT_OVERLAY=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x3000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
+# CONFIG_USE_BOOTCOMMAND is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_CMD_BOOTEFI_HELLO=y
+CONFIG_CMD_BOOTEFI_SELFTEST=y
+CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_GPT=y
+CONFIG_RANDOM_UUID=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_UBI=y
+CONFIG_CMD_UBIFS=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_POWEROFF=y
+CONFIG_CMD_WDT=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_FS_FAT=y
+CONFIG_FAT_WRITE=y
+CONFIG_MP=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1088a-ten64"
+CONFIG_EMC230X=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_OFFSET=0x500000
+CONFIG_ENV_SIZE=0x80000
+CONFIG_ENV_SECT_SIZE=0x80000
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_CMD_FAN=y
+CONFIG_FANCONTROL=y
+CONFIG_DM_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_EON=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_E1000=y
+# CONFIG_ID_EEPROM is not set
+CONFIG_MII=y
+CONFIG_NVME=y
+CONFIG_CMD_PCI=y
+CONFIG_PCI=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE_RC=y
+CONFIG_SYS_NS16550=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_UBI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_GADGET=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
+CONFIG_DM_I2C=y
+CONFIG_DM_GPIO=y
+CONFIG_ARM_SMCCC=y
+CONFIG_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_CMD_MTD=y
+CONFIG_LOGLEVEL=7
+CONFIG_MTDPARTS_DEFAULT="mtdparts=spi-nand0:8m(reserved),32m(recovery),108m(ubia),108m(ubib);nor1:1m(bl2),2m(bl3),2m(mcfirmware),512k(ubootenv),256k(dpl),256k(dpc),256k(devicetree)"
+CONFIG_MPC8XXX_GPIO=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_RX8025=y
+CONFIG_CMD_NVEDIT_EFI=y
+CONFIG_CMD_EFIDEBUG=y
+CONFIG_DM_ETH=y
+CONFIG_PCI_INIT_R=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_VITESSE=y
+CONFIG_DM_MDIO=y
+CONFIG_FSL_LS_MDIO=y
+CONFIG_SYS_MALLOC_F=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TPM=y
+CONFIG_CMD_TPM=y
+CONFIG_TPM_ATMEL_TWI=y
+CONFIG_MISC=y
+CONFIG_USB5744=y
+CONFIG_TEN64_CONTROLLER=y
+CONFIG_DM_SCSI=y
+CONFIG_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_WDT=y
+CONFIG_WDT_SP805=y