ColdFire: Add SBF support for M52277EVB
Add serial boot support
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
diff --git a/cpu/mcf5227x/start.S b/cpu/mcf5227x/start.S
index becaab7..9387250 100644
--- a/cpu/mcf5227x/start.S
+++ b/cpu/mcf5227x/start.S
@@ -46,6 +46,11 @@
addl #60,%sp; /* space for 15 regs */ \
rte;
+#if defined(CONFIG_CF_SBF)
+#define ASM_DRAMINIT (asm_dram_init - TEXT_BASE + CONFIG_SYS_INIT_RAM_ADDR)
+#define ASM_SBF_IMG_HDR (asm_sbf_img_hdr - TEXT_BASE + CONFIG_SYS_INIT_RAM_ADDR)
+#endif
+
.text
/*
* Vector table. This is used for initial platform startup.
@@ -53,8 +58,14 @@
*/
_vectors:
-INITSP: .long 0x00000000 /* Initial SP */
-INITPC: .long _START /* Initial PC */
+#if defined(CONFIG_CF_SBF)
+INITSP: .long 0 /* Initial SP */
+INITPC: .long ASM_DRAMINIT /* Initial PC */
+#else
+INITSP: .long 0 /* Initial SP */
+INITPC: .long _START /* Initial PC */
+#endif
+
vector02: .long _FAULT /* Access Error */
vector03: .long _FAULT /* Address Error */
vector04: .long _FAULT /* Illegal Instruction */
@@ -83,6 +94,7 @@
vector1E: .long _FAULT /* Autovector Level 6 */
vector1F: .long _FAULT /* Autovector Level 7 */
+#if !defined(CONFIG_CF_SBF)
/* TRAP #0 - #15 */
vector20_2F:
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
@@ -122,9 +134,231 @@
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
.long _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
+#endif
+
+#if defined(CONFIG_CF_SBF)
+ /* Image header: chksum 4 bytes, len 4 bytes, img dest 4 bytes */
+asm_sbf_img_hdr:
+ .long 0x00000000 /* checksum, not yet implemented */
+ .long 0x00020000 /* image length */
+ .long TEXT_BASE /* image to be relocated at */
+
+asm_dram_init:
+ move.l #(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_CTRL), %d0
+ movec %d0, %RAMBAR1 /* init Rambar */
+ move.l #(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET), %sp
+ clr.l %sp@-
+
+ /* Must disable global address */
+ move.l #0xFC008000, %a1
+ move.l #(CONFIG_SYS_CS0_BASE), (%a1)
+ move.l #0xFC008008, %a1
+ move.l #(CONFIG_SYS_CS0_CTRL), (%a1)
+ move.l #0xFC008004, %a1
+ move.l #(CONFIG_SYS_CS0_MASK), (%a1)
+
+ /*
+ * Dram Initialization
+ * a1, a2, and d0
+ */
+ /* mscr sdram */
+ move.l #0xFC0A4074, %a1
+ move.b #(CONFIG_SYS_SDRAM_DRV_STRENGTH), (%a1)
+ nop
+
+ /* SDRAM Chip 0 and 1 */
+ move.l #0xFC0B8110, %a1
+ move.l #0xFC0B8114, %a2
+
+ /* calculate the size */
+ move.l #0x13, %d1
+ move.l #(CONFIG_SYS_SDRAM_SIZE), %d2
+#ifdef CONFIG_SYS_SDRAM_BASE1
+ lsr.l #1, %d2
+#endif
+
+dramsz_loop:
+ lsr.l #1, %d2
+ add.l #1, %d1
+ cmp.l #1, %d2
+ bne dramsz_loop
+
+ /* SDRAM Chip 0 and 1 */
+ move.l #(CONFIG_SYS_SDRAM_BASE), (%a1)
+ or.l %d1, (%a1)
+#ifdef CONFIG_SYS_SDRAM_BASE1
+ move.l #(CONFIG_SYS_SDRAM_BASE1), (%a2)
+ or.l %d1, (%a2)
+#endif
+ nop
+
+ /* dram cfg1 and cfg2 */
+ move.l #0xFC0B8008, %a1
+ move.l #(CONFIG_SYS_SDRAM_CFG1), (%a1)
+ nop
+ move.l #0xFC0B800C, %a2
+ move.l #(CONFIG_SYS_SDRAM_CFG2), (%a2)
+ nop
+
+ move.l #0xFC0B8000, %a1 /* Mode */
+ move.l #0xFC0B8004, %a2 /* Ctrl */
+
+ /* Issue PALL */
+ move.l #(CONFIG_SYS_SDRAM_CTRL + 2), (%a2)
+ nop
+
+ /* Issue LEMR */
+ move.l #(CONFIG_SYS_SDRAM_MODE), (%a1)
+ nop
+ move.l #(CONFIG_SYS_SDRAM_EMOD), (%a1)
+ nop
+
+ move.l #1000, %d0
+wait1000:
+ nop
+ subq.l #1, %d0
+ bne wait1000
+
+ /* Issue PALL */
+ move.l #(CONFIG_SYS_SDRAM_CTRL + 2), (%a2)
+ nop
+
+ /* Perform two refresh cycles */
+ move.l #(CONFIG_SYS_SDRAM_CTRL + 4), %d0
+ nop
+ move.l %d0, (%a2)
+ move.l %d0, (%a2)
+ nop
+
+ move.l #(CONFIG_SYS_SDRAM_CTRL), %d0
+ and.l #0x7FFFFFFF, %d0
+ or.l #0x10000c00, %d0
+ move.l %d0, (%a2)
+ nop
+
+ /*
+ * DSPI Initialization
+ * a0 - general, sram - 0x80008000 - 32, see M52277EVB.h
+ * a1 - dspi status
+ * a2 - dtfr
+ * a3 - drfr
+ * a4 - Dst addr
+ */
+
+ /* Enable pins for DSPI mode - chip-selects are enabled later */
+ move.l #0xFC0A4036, %a0
+ move.b #0x3F, %d0
+ move.b %d0, (%a0)
+
+ /* DSPI CS */
+#ifdef CONFIG_SYS_DSPI_CS0
+ move.b (%a0), %d0
+ or.l #0xC0, %d0
+ move.b %d0, (%a0)
+#endif
+#ifdef CONFIG_SYS_DSPI_CS2
+ move.l #0xFC0A4037, %a0
+ move.b (%a0), %d0
+ or.l #0x10, %d0
+ move.b %d0, (%a0)
+#endif
+ nop
+
+ /* Configure DSPI module */
+ move.l #0xFC05C000, %a0
+ move.l #0x80FF0C00, (%a0) /* Master, clear TX/RX FIFO */
+
+ move.l #0xFC05C00C, %a0
+ move.l #0x3E000011, (%a0)
+
+ move.l #0xFC05C034, %a2 /* dtfr */
+ move.l #0xFC05C03B, %a3 /* drfr */
+
+ move.l #(ASM_SBF_IMG_HDR + 4), %a1
+ move.l (%a1)+, %d5
+ move.l (%a1), %a4
+
+ move.l #(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_SBFHDR_DATA_OFFSET), %a0
+ move.l #(CONFIG_SYS_SBFHDR_SIZE), %d4
+
+ move.l #0xFC05C02C, %a1 /* dspi status */
+
+ /* Issue commands and address */
+ move.l #0x8004000B, %d2 /* Fast Read Cmd */
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ move.l #0x80040000, %d2 /* Address byte 2 */
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ move.l #0x80040000, %d2 /* Address byte 1 */
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ move.l #0x80040000, %d2 /* Address byte 0 */
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ move.l #0x80040000, %d2 /* Dummy Wr and Rd */
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ /* Transfer serial boot header to sram */
+asm_dspi_rd_loop1:
+ move.l #0x80040000, %d2
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ move.b %d1, (%a0) /* read, copy to dst */
+
+ add.l #1, %a0 /* inc dst by 1 */
+ sub.l #1, %d4 /* dec cnt by 1 */
+ bne asm_dspi_rd_loop1
+
+ /* Transfer u-boot from serial flash to memory */
+asm_dspi_rd_loop2:
+ move.l #0x80040000, %d2
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ move.b %d1, (%a4) /* read, copy to dst */
+
+ add.l #1, %a4 /* inc dst by 1 */
+ sub.l #1, %d5 /* dec cnt by 1 */
+ bne asm_dspi_rd_loop2
+
+ move.l #0x00040000, %d2 /* Terminate */
+ jsr asm_dspi_wr_status
+ jsr asm_dspi_rd_status
+
+ /* jump to memory and execute */
+ move.l #(TEXT_BASE + 0x400), %a0
+ move.l %a0, (%a1)
+ jmp (%a0)
+
+asm_dspi_wr_status:
+ move.l (%a1), %d0 /* status */
+ and.l #0x0000F000, %d0
+ cmp.l #0x00003000, %d0
+ bgt asm_dspi_wr_status
+
+ move.l %d2, (%a2)
+ rts
+
+asm_dspi_rd_status:
+ move.l (%a1), %d0 /* status */
+ and.l #0x000000F0, %d0
+ lsr.l #4, %d0
+ cmp.l #0, %d0
+ beq asm_dspi_rd_status
+
+ move.b (%a3), %d1
+ rts
+#endif /* CONFIG_CF_SBF */
.text
-
+ . = 0x400
.globl _start
_start:
nop
@@ -132,11 +366,16 @@
move.w #0x2700,%sr /* Mask off Interrupt */
/* Set vector base register at the beginning of the Flash */
+#if defined(CONFIG_CF_SBF)
+ move.l #TEXT_BASE, %d0
+ movec %d0, %VBR
+#else
move.l #CONFIG_SYS_FLASH_BASE, %d0
movec %d0, %VBR
move.l #(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_CTRL), %d0
movec %d0, %RAMBAR1
+#endif
/* initialize general use internal ram */
move.l #0, %d0