* Patches by David Müller, 14 Nov 2003:
- board/mpl/common/common_util.c
* implement support for BZIP2 compressed images
* various cleanups (printf -> puts, ...)
- board/mpl/common/flash.c
* report correct errors to upper layers
* check the erase fail and VPP low bits in status reg
- board/mpl/vcma9/cmd_vcma9.c
- board/mpl/vcma9/flash.c
* various cleanups (printf -> puts, ...)
- common/cmd_usb.c
* fix typo in comment
- cpu/arm920t/usb_ohci.c
* support for S3C2410 is missing in #if line
- drivers/cs8900.c
* reinit some registers in case of error (cable missing, ...)
- fs/fat/fat.c
* support for USB/MMC devices is missing in #if line
- include/configs/MIP405.h
- include/configs/PIP405.h
* enable BZIP2 support
* enlarge malloc space to 1MiB because of BZIP2 support
- include/configs/VCMA9.h
* enable BZIP2 support
* enlarge malloc space to 1MiB because of BZIP2 support
* enable USB support
- lib_arm/armlinux.c
* change calling convention of ARM Linux kernel as
described on http://www.arm.linux.org.uk/developer/booting.php
* Patch by Thomas Lange, 14 Nov 2003:
Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to
support all these AMD boards.
* Patch by Thomas Lange, 14 Nov 2003:
Workaround for mips au1x00 physical memory accesses (the au1x00
uses a 36 bit bus internally and cannot access physical memory
directly. Use the uncached SDRAM address instead of the physical
one.)
diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
index 8a09da6..9ca80ab 100644
--- a/include/configs/VCMA9.h
+++ b/include/configs/VCMA9.h
@@ -42,6 +42,7 @@
#define CONFIG_ARM920T 1 /* This is an ARM920T Core */
#define CONFIG_S3C2410 1 /* in a SAMSUNG S3C2410 SoC */
#define CONFIG_VCMA9 1 /* on a MPL VCMA9 Board */
+#define LITTLEENDIAN 1 /* used by usb_ohci.c */
/* input clock of PLL */
#define CONFIG_SYS_CLK_FREQ 12000000/* VCMA9 has 12MHz input clock */
@@ -63,10 +64,13 @@
/*CFG_CMD_NAND |*/ \
CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
- /*CFG_CMD_USB |*/ \
+ CFG_CMD_USB | \
CFG_CMD_REGINFO | \
+ CFG_CMD_FAT | \
CFG_CMD_DATE | \
CFG_CMD_ELF | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_PING | \
CFG_CMD_BSP)
/* this must be included after the definiton of CONFIG_COMMANDS */
@@ -96,11 +100,11 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+/*#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)*/
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_MONITOR_LEN (256 * 1024)
-#define CFG_MALLOC_LEN (128 * 1024)
+#define CFG_MALLOC_LEN (1024 * 1024) /* BUNZIP2 needs a lot of RAM */
/*
* Hardware drivers
@@ -119,14 +123,13 @@
/************************************************************
* USB support
************************************************************/
-#if 0
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_KEYBOARD
-#define CONFIG_USB_STORAGE
+#define CONFIG_USB_OHCI 1
+#define CONFIG_USB_KEYBOARD 1
+#define CONFIG_USB_STORAGE 1
+#define CONFIG_DOS_PARTITION 1
/* Enable needed helper functions */
#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
-#endif
/************************************************************
* RTC
@@ -139,7 +142,11 @@
#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 5
+/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
+#define CONFIG_BOOT_RETRY_TIME -10 /* feature is avaiable but not enabled */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
+
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_IPADDR 10.0.0.110
#define CONFIG_SERVERIP 10.0.0.1
@@ -176,6 +183,9 @@
/* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+/* support BZIP2 compression */
+#define CONFIG_BZIP2 1
+
/************************************************************
* Ident
************************************************************/