Adding Support for BAV335x boards
diff --git a/board/birdland/bav335x/board.c b/board/birdland/bav335x/board.c
new file mode 100644
index 0000000..d1e1c8c
--- /dev/null
+++ b/board/birdland/bav335x/board.c
@@ -0,0 +1,430 @@
+/*
+ * board.c
+ *
+ * Board functions for Birdland Audio BAV335x Network Processor
+ *
+ * Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
+#include <environment.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPIO that controls power to DDR on EVM-SK */
+#define GPIO_DDR_VTT_EN 7
+
+static __maybe_unused struct ctrl_dev *cdev =
+ (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+
+
+/*
+ * Read header information from EEPROM into global structure.
+ */
+static int read_eeprom(struct board_eeconfig *header)
+{
+ /* Check if baseboard eeprom is available */
+ if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR))
+ return -ENODEV;
+
+ /* read the eeprom using i2c */
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
+ sizeof(struct board_eeconfig)))
+ return -EIO;
+
+ if (header->magic != BOARD_MAGIC) {
+ /* read the i2c eeprom again using only a 1 byte address */
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
+ sizeof(struct board_eeconfig)))
+ return -EIO;
+
+ if (header->magic != BOARD_MAGIC)
+ return -EINVAL;
+ }
+ return 0;
+}
+
+
+
+
+enum board_type get_board_type(bool debug)
+{
+ int ecode;
+ struct board_eeconfig header;
+
+ ecode = read_eeprom(&header);
+ if (ecode == 0) {
+ if (header.version[1] == 'A') {
+ if (debug)
+ puts("=== Detected Board model BAV335x Rev.A");
+ return BAV335A;
+ } else if (header.version[1] == 'B') {
+ if (debug)
+ puts("=== Detected Board model BAV335x Rev.B");
+ return BAV335B;
+ } else if (debug) {
+ puts("### Un-known board model in serial-EE\n");
+ }
+ } else if (debug) {
+ switch (ecode) {
+ case -ENODEV:
+ puts("### Board doesn't have a serial-EE\n");
+ break;
+ case -EINVAL:
+ puts("### Board serial-EE signature is incorrect.\n");
+ break;
+ default:
+ puts("### IO Error reading serial-EE.\n");
+ break;
+ }
+ }
+
+#if (CONFIG_BAV_VERSION == 1)
+ if (debug)
+ puts("### Selecting BAV335A as per config\n");
+ return BAV335A;
+#elif (CONFIG_BAV_VERSION == 2)
+ if (debug)
+ puts("### Selecting BAV335B as per config\n");
+ return BAV335B;
+#endif
+#if (NOT_DEFINED == 2)
+#error "SHOULD NEVER DISPLAY THIS"
+#endif
+
+ if (debug)
+ puts("### Defaulting to model BAV335x Rev.B\n");
+ return BAV335B;
+}
+
+
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+static const struct ddr_data ddr3_bav335x_data = {
+ .datardsratio0 = MT41K256M16HA125E_RD_DQS,
+ .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+ .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_bav335x_cmd_ctrl_data = {
+ .cmd0csratio = MT41K256M16HA125E_RATIO,
+ .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+ .cmd1csratio = MT41K256M16HA125E_RATIO,
+ .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+ .cmd2csratio = MT41K256M16HA125E_RATIO,
+ .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+
+static struct emif_regs ddr3_bav335x_emif_reg_data = {
+ .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+ .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+ .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+ .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+ .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+ .zq_config = MT41K256M16HA125E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ if (serial_tstc() && serial_getc() == 'c')
+ return 1;
+
+#ifdef CONFIG_SPL_ENV_SUPPORT
+ env_init();
+ env_relocate_spec();
+ if (getenv_yesno("boot_os") != 1)
+ return 1;
+#endif
+
+ return 0;
+}
+#endif
+
+#define OSC (V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+ 266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_evm_sk = {
+ 303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_bone_black = {
+ 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+ /* debug print detect status */
+ (void)get_board_type(true);
+
+ /* Get the frequency */
+ /* dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); */
+ dpll_mpu_opp100.m = MPUPLL_M_1000;
+
+ if (i2c_probe(TPS65217_CHIP_PM))
+ return;
+
+ /* Set the USB Current Limit */
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
+ TPS65217_USB_INPUT_CUR_LIMIT_1800MA,
+ TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+ puts("! tps65217_reg_write: could not set USB limit\n");
+
+ /* Set the Core Voltage (DCDC3) to 1.125V */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+ TPS65217_DCDC_VOLT_SEL_1125MV)) {
+ puts("! tps65217_reg_write: could not set Core Voltage\n");
+ return;
+ }
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* Set the MPU Voltage (DCDC2) */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC2,
+ TPS65217_DCDC_VOLT_SEL_1325MV)) {
+ puts("! tps65217_reg_write: could not set MPU Voltage\n");
+ return;
+ }
+
+ /*
+ * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
+ * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
+ */
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS1,
+ TPS65217_LDO_VOLTAGE_OUT_1_8, TPS65217_LDO_MASK))
+ puts("! tps65217_reg_write: could not set LDO3\n");
+
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS2,
+ TPS65217_LDO_VOLTAGE_OUT_3_3, TPS65217_LDO_MASK))
+ puts("! tps65217_reg_write: could not set LDO4\n");
+
+ /* Set MPU Frequency to what we detected now that voltages are set */
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+ return &dpll_ddr_bone_black;
+}
+
+void set_uart_mux_conf(void)
+{
+#if CONFIG_CONS_INDEX == 1
+ enable_uart0_pin_mux();
+#elif CONFIG_CONS_INDEX == 2
+ enable_uart1_pin_mux();
+#elif CONFIG_CONS_INDEX == 3
+ enable_uart2_pin_mux();
+#elif CONFIG_CONS_INDEX == 4
+ enable_uart3_pin_mux();
+#elif CONFIG_CONS_INDEX == 5
+ enable_uart4_pin_mux();
+#elif CONFIG_CONS_INDEX == 6
+ enable_uart5_pin_mux();
+#endif
+}
+
+void set_mux_conf_regs(void)
+{
+ enum board_type board;
+
+ board = get_board_type(false);
+ enable_board_pin_mux(board);
+}
+
+const struct ctrl_ioregs ioregs_bonelt = {
+ .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+
+void sdram_init(void)
+{
+ config_ddr(400, &ioregs_bonelt,
+ &ddr3_bav335x_data,
+ &ddr3_bav335x_cmd_ctrl_data,
+ &ddr3_bav335x_emif_reg_data, 0);
+}
+#endif
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+ hw_watchdog_init();
+#endif
+
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
+ gpmc_init();
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ setenv("board_name", "BAV335xB");
+ setenv("board_rev", "B"); /* Fix me, but why bother.. */
+#endif
+ return 0;
+}
+#endif
+
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+ return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_addr = 0,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_addr = 1,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = CPSW_MDIO_BASE,
+ .cpsw_base = CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .bd_ram_ofs = 0x2000,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+#endif
+
+
+/*
+ * This function will:
+ * Perform fixups to the PHY present on certain boards. We only need this
+ * function in:
+ * - SPL with either CPSW or USB ethernet support
+ * - Full U-Boot, with either CPSW or USB ethernet
+ * Build in only these cases to avoid warnings about unused variables
+ * when we build an SPL that has neither option but full U-Boot will.
+ */
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\
+ defined(CONFIG_SPL_BUILD)) || \
+ ((defined(CONFIG_DRIVER_TI_CPSW) || \
+ defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+ !defined(CONFIG_SPL_BUILD))
+int board_eth_init(bd_t *bis)
+{
+ int ecode, rv, n;
+ uint8_t mac_addr[6];
+ struct board_eeconfig header;
+ __maybe_unused enum board_type board;
+
+ /* Default manufacturing address; used when no EE or invalid */
+ n = 0;
+ mac_addr[0] = 0;
+ mac_addr[1] = 0x20;
+ mac_addr[2] = 0x18;
+ mac_addr[3] = 0x1C;
+ mac_addr[4] = 0x00;
+ mac_addr[5] = 0x01;
+
+ ecode = read_eeprom(&header);
+ /* if we have a valid EE, get mac address from there */
+ if ((ecode == 0) &&
+ is_valid_ether_addr((const u8 *)&header.mac_addr[0][0])) {
+ memcpy(mac_addr, (const void *)&header.mac_addr[0][0], 6);
+ }
+
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+
+ if (!getenv("ethaddr")) {
+ printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ }
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+ board = get_board_type(false);
+
+ /* Rev.A uses 10/100 PHY in mii mode */
+ if (board == BAV335A) {
+ writel(MII_MODE_ENABLE, &cdev->miisel);
+ cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
+ cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
+ }
+ /* Rev.B (default) uses GB PHY in rmii mode */
+ else {
+ writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
+ cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if
+ = PHY_INTERFACE_MODE_RGMII;
+ }
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0)
+ printf("Error %d registering CPSW switch\n", rv);
+ else
+ n += rv;
+#endif
+
+#endif
+
+ return n;
+}
+#endif