am335x, shc: adapt shc board to DM
port the am335x based shc board to DM, to get rid
of DW warnings when compiling U-Boot.
- remove uneccessary board code
- adapt defconfigs
- remove unneeded defconfigs
configs/am335x_shc_prompt_defconfig
configs/am335x_shc_sdboot_prompt_defconfig
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/board/bosch/shc/MAINTAINERS b/board/bosch/shc/MAINTAINERS
index 137e647..58104cc 100644
--- a/board/bosch/shc/MAINTAINERS
+++ b/board/bosch/shc/MAINTAINERS
@@ -6,8 +6,6 @@
F: configs/am335x_shc_defconfig
F: configs/am335x_shc_ict_defconfig
F: configs/am335x_shc_netboot_defconfig
-F: configs/am335x_shc_prompt_defconfig
F: configs/am335x_shc_sdboot_defconfig
-F: configs/am335x_shc_sdboot_prompt_defconfig
F: arch/arm/dts/am335x-shc.dts
F: arch/arm/dts/am335x-shc-u-boot.dtsi
diff --git a/board/bosch/shc/board.c b/board/bosch/shc/board.c
index 1ec9a3f..feed63b 100644
--- a/board/bosch/shc/board.c
+++ b/board/bosch/shc/board.c
@@ -38,10 +38,6 @@
DECLARE_GLOBAL_DATA_PTR;
-#if defined(CONFIG_SPL_BUILD) || \
- (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_DM_ETH))
-static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-#endif
static struct shc_eeprom __attribute__((section(".data"))) header;
static int shc_eeprom_valid;
@@ -254,7 +250,7 @@
}
}
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+#if defined(CONFIG_SPL_BUILD)
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
@@ -275,6 +271,8 @@
leds_set_booting();
}
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
#define MPU_SPREADING_PERMILLE 18 /* Spread 1.8 percent */
#define OSC (V_OSCK/1000000)
/* Bosch: Predivider must be fixed to 4, so N = 4-1 */
@@ -466,118 +464,14 @@
}
#endif
-#ifndef CONFIG_DM_ETH
-#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
- (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
-static void cpsw_control(int enabled)
-{
- /* VTP can be added here */
-
- return;
-}
-
-static struct cpsw_slave_data cpsw_slaves[] = {
- {
- .slave_reg_ofs = 0x208,
- .sliver_reg_ofs = 0xd80,
- .phy_addr = 0,
- },
- {
- .slave_reg_ofs = 0x308,
- .sliver_reg_ofs = 0xdc0,
- .phy_addr = 1,
- },
-};
-
-static struct cpsw_platform_data cpsw_data = {
- .mdio_base = CPSW_MDIO_BASE,
- .cpsw_base = CPSW_BASE,
- .mdio_div = 0xff,
- .channels = 8,
- .cpdma_reg_ofs = 0x800,
- .slaves = 1,
- .slave_data = cpsw_slaves,
- .ale_reg_ofs = 0xd00,
- .ale_entries = 1024,
- .host_port_reg_ofs = 0x108,
- .hw_stats_reg_ofs = 0x900,
- .bd_ram_ofs = 0x2000,
- .mac_control = (1 << 5),
- .control = cpsw_control,
- .host_port_num = 0,
- .version = CPSW_CTRL_VERSION_2,
-};
-#endif
-
-/*
- * This function will:
- * Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr
- * in the environment
- * Perform fixups to the PHY present on certain boards. We only need this
- * function in:
- * - SPL with either CPSW or USB ethernet support
- * - Full U-Boot, with either CPSW or USB ethernet
- * Build in only these cases to avoid warnings about unused variables
- * when we build an SPL that has neither option but full U-Boot will.
- */
-#if ((defined(CONFIG_SPL_ETH_SUPPORT) || \
- defined(CONFIG_SPL_USB_ETHER)) && \
- defined(CONFIG_SPL_BUILD)) || \
- ((defined(CONFIG_DRIVER_TI_CPSW) || \
- defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
- !defined(CONFIG_SPL_BUILD))
-int board_eth_init(bd_t *bis)
-{
- int rv, n = 0;
- uint8_t mac_addr[6];
- uint32_t mac_hi, mac_lo;
-
- /* try reading mac address from efuse */
- mac_lo = readl(&cdev->macid0l);
- mac_hi = readl(&cdev->macid0h);
- mac_addr[0] = mac_hi & 0xFF;
- mac_addr[1] = (mac_hi & 0xFF00) >> 8;
- mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
- mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
- mac_addr[4] = mac_lo & 0xFF;
- mac_addr[5] = (mac_lo & 0xFF00) >> 8;
-
-#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
- (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
- if (!env_get("ethaddr")) {
- printf("<ethaddr> not set. Validating first E-fuse MAC\n");
-
- if (is_valid_ethaddr(mac_addr))
- eth_env_set_enetaddr("ethaddr", mac_addr);
- }
-
- writel(MII_MODE_ENABLE, &cdev->miisel);
- cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
- cpsw_slaves[1].phy_if = cpsw_slaves[0].phy_if;
- rv = cpsw_register(&cpsw_data);
- if (rv < 0)
- printf("Error %d registering CPSW switch\n", rv);
- else
- n += rv;
-#endif
-
#if defined(CONFIG_USB_ETHER) && \
(!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USB_ETHER))
- if (is_valid_ethaddr(mac_addr))
- eth_env_set_enetaddr("usbnet_devaddr", mac_addr);
-
- rv = usb_eth_initialize(bis);
- if (rv < 0)
- printf("Error %d registering USB_ETHER\n", rv);
- else
- n += rv;
-#endif
- return n;
+int board_eth_init(bd_t *bis)
+{
+ return usb_eth_initialize(bis);
}
#endif
-#endif /* CONFIG_DM_ETH */
-
#ifdef CONFIG_SHOW_BOOT_PROGRESS
static void bosch_check_reset_pin(void)
{
@@ -624,24 +518,9 @@
break;
}
}
-#endif
void arch_preboot_os(void)
{
leds_set_finish();
}
-
-#if defined(CONFIG_MMC)
-int board_mmc_init(bd_t *bis)
-{
- int ret;
-
- /* Bosch: Do not enable 52MHz for eMMC device to avoid EMI */
- ret = omap_mmc_init(0, MMC_MODE_HS_52MHz, 26000000, -1, -1);
- if (ret)
- return ret;
-
- ret = omap_mmc_init(1, MMC_MODE_HS_52MHz, 26000000, -1, -1);
- return ret;
-}
#endif