arm64: zynqmp: Use assigned-clock-rates for setting up clock in SOM
With limited low level configuration done via psu-init only IPs connected
on SOM are initialized and configured. All IPs connected to carrier card
are not initialized. There is a need to do proper reset, pin configuration
and also clock setting.
The patch targets the last part which is setting up proper clock for USBs
and SDs.
Also setup proper bus width for SD cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/d9f80b2551bd246c3d7ecb09b516806c8dc83ed9.1645629459.git.michal.simek@xilinx.com
diff --git a/arch/arm/dts/zynqmp-clk-ccf.dtsi b/arch/arm/dts/zynqmp-clk-ccf.dtsi
index 86b9907..7b09d75 100644
--- a/arch/arm/dts/zynqmp-clk-ccf.dtsi
+++ b/arch/arm/dts/zynqmp-clk-ccf.dtsi
@@ -215,10 +215,12 @@
&sdhci0 {
clocks = <&zynqmp_clk SDIO0_REF>, <&zynqmp_clk LPD_LSBUS>;
+ assigned-clocks = <&zynqmp_clk SDIO0_REF>;
};
&sdhci1 {
clocks = <&zynqmp_clk SDIO1_REF>, <&zynqmp_clk LPD_LSBUS>;
+ assigned-clocks = <&zynqmp_clk SDIO1_REF>;
};
&spi0 {
@@ -255,10 +257,12 @@
&usb0 {
clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+ assigned-clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
};
&usb1 {
clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+ assigned-clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
};
&watchdog0 {
diff --git a/arch/arm/dts/zynqmp-sck-kv-g-revA.dts b/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
index 34fb592..f58ad69 100644
--- a/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
+++ b/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
@@ -154,6 +154,8 @@
no-1-8-v;
disable-wp;
xlnx,mio-bank = <1>;
+ assigned-clock-rates = <187498123>;
+ bus-width = <8>;
};
&gem3 { /* required by spec */
diff --git a/arch/arm/dts/zynqmp-sck-kv-g-revB.dts b/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
index 35247b0..7236e03 100644
--- a/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
+++ b/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
@@ -109,6 +109,7 @@
pinctrl-0 = <&pinctrl_usb0_default>;
phy-names = "usb3-phy";
phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+ assigned-clock-rates = <250000000>, <20000000>;
usb5744: usb-hub { /* u43 */
status = "okay";
@@ -140,6 +141,8 @@
clk-phase-sd-hs = <126>, <60>;
clk-phase-uhs-sdr25 = <120>, <60>;
clk-phase-uhs-ddr50 = <126>, <48>;
+ assigned-clock-rates = <187498123>;
+ bus-width = <8>;
};
&gem3 { /* required by spec */
diff --git a/arch/arm/dts/zynqmp-sm-k26-revA.dts b/arch/arm/dts/zynqmp-sm-k26-revA.dts
index 5f55df2..e9baf4c 100644
--- a/arch/arm/dts/zynqmp-sm-k26-revA.dts
+++ b/arch/arm/dts/zynqmp-sm-k26-revA.dts
@@ -189,6 +189,7 @@
disable-wp;
bus-width = <8>;
xlnx,mio-bank = <0>;
+ assigned-clock-rates = <187498123>;
};
&spi1 { /* MIO6, 9-11 */