ARM: kirkwood: add SBx81LIFXCAT board
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/SBx81LIFXCAT.h b/include/configs/SBx81LIFXCAT.h
new file mode 100644
index 0000000..0491832
--- /dev/null
+++ b/include/configs/SBx81LIFXCAT.h
@@ -0,0 +1,114 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
+ */
+
+#ifndef _CONFIG_SBX81LIFXCAT_H
+#define _CONFIG_SBX81LIFXCAT_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_BUILD_TARGET "u-boot.kwb"
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_GPIO 1
+
+#define CONFIG_MISC_INIT_R /* call misc_init_r */
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
+#define MTDPARTS_MTDOOPS "errlog"
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
+#define CONFIG_ENV_SIZE 0x02000
+#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here - 768K */
+
+/*
+ * U-Boot bootcode configuration
+ */
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
+#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
+
+/* size in bytes reserved for initial data */
+
+#include <asm/arch/config.h>
+/* There is no PHY directly connected so don't ask it for link status */
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi over miiphy interface */
+#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
+#define CONFIG_PHY_BASE_ADR 0x01
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#endif /* CONFIG_CMD_NET */
+
+#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
+
+#endif /* _CONFIG_SBX81LIFXCAT_H */