sun8i: h2: Add initial Orange Pi R1 support
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 493652e..297160b 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -358,6 +358,7 @@
sun8i-a83t-tbs-a711.dts
dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h2-plus-libretech-all-h3-cc.dtb \
+ sun8i-h2-plus-orangepi-r1.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
new file mode 100644
index 0000000..c652ac3
--- /dev/null
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
@@ -0,0 +1,101 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* Orange Pi R1 is based on Orange Pi Zero design */
+#include "sun8i-h2-plus-orangepi-zero.dts"
+
+/ {
+ model = "Xunlong Orange Pi R1";
+ compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus";
+
+ /delete-node/ reg_vcc_wifi;
+
+ /*
+ * Ths pin of this regulator is the same with the Wi-Fi extra
+ * regulator on the original Zero. However it's used for USB
+ * Ethernet rather than the Wi-Fi now.
+ */
+ reg_vcc_usb_eth: reg-vcc-usb-ethernet {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-ethernet";
+ enable-active-high;
+ gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ aliases {
+ ethernet1 = &rtl8189etv;
+ };
+};
+
+/*
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
+ };
+};
+*/
+
+&ohci1 {
+ /*
+ * RTL8152B USB-Ethernet adapter is connected to USB1,
+ * and it's a USB 2.0 device. So the OHCI1 controller
+ * can be left disabled.
+ */
+ status = "disabled";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+
+ rtl8189etv: sdio_wifi@1 {
+ reg = <1>;
+ };
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc_usb_eth>;
+};