net: phy: Add support for ethernet-phy-id with gpio reset
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 4f8d33c..74339a2 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -307,6 +307,14 @@
as bridge between MAC connected over GMII and external phy that
is connected over RGMII interface.
+config PHY_ETHERNET_ID
+ bool "Read ethernet PHY id"
+ depends on DM_GPIO
+ default y if ZYNQ_GEM
+ help
+ Enable this config to read ethernet phy id from the phy node of DT
+ and create a phy device using id.
+
config PHY_FIXED
bool "Fixed-Link PHY"
depends on DM_ETH
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 77f7f60..b28440b 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -32,6 +32,7 @@
obj-$(CONFIG_PHY_TI_DP83869) += dp83869.o
obj-$(CONFIG_PHY_XILINX) += xilinx_phy.o
obj-$(CONFIG_PHY_XILINX_GMII2RGMII) += xilinx_gmii2rgmii.o
+obj-$(CONFIG_PHY_ETHERNET_ID) += ethernet_id.o
obj-$(CONFIG_PHY_VITESSE) += vitesse.o
obj-$(CONFIG_PHY_MSCC) += mscc.o
obj-$(CONFIG_PHY_FIXED) += fixed.o
diff --git a/drivers/net/phy/ethernet_id.c b/drivers/net/phy/ethernet_id.c
new file mode 100644
index 0000000..5617ac3
--- /dev/null
+++ b/drivers/net/phy/ethernet_id.c
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ethernet phy reset driver
+ *
+ * Copyright (C) 2022 Xilinx, Inc.
+ */
+
+#include <common.h>
+#include <dm/device_compat.h>
+#include <phy.h>
+#include <linux/delay.h>
+#include <asm/gpio.h>
+
+struct phy_device *phy_connect_phy_id(struct mii_dev *bus, struct udevice *dev,
+ phy_interface_t interface)
+{
+ struct phy_device *phydev;
+ struct ofnode_phandle_args phandle_args;
+ struct gpio_desc gpio;
+ ofnode node;
+ u32 id, assert, deassert;
+ u16 vendor, device;
+ int ret;
+
+ if (dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
+ &phandle_args))
+ return NULL;
+
+ if (!ofnode_valid(phandle_args.node))
+ return NULL;
+
+ node = phandle_args.node;
+
+ ret = ofnode_read_eth_phy_id(node, &vendor, &device);
+ if (ret) {
+ dev_err(dev, "Failed to read eth PHY id, err: %d\n", ret);
+ return NULL;
+ }
+
+ ret = gpio_request_by_name_nodev(node, "reset-gpios", 0, &gpio,
+ GPIOD_ACTIVE_LOW);
+ if (!ret) {
+ assert = ofnode_read_u32_default(node, "reset-assert-us", 0);
+ deassert = ofnode_read_u32_default(node,
+ "reset-deassert-us", 0);
+ ret = dm_gpio_set_value(&gpio, 1);
+ if (ret) {
+ dev_err(dev, "Failed assert gpio, err: %d\n", ret);
+ return NULL;
+ }
+
+ udelay(assert);
+
+ ret = dm_gpio_set_value(&gpio, 0);
+ if (ret) {
+ dev_err(dev, "Failed deassert gpio, err: %d\n", ret);
+ return NULL;
+ }
+
+ udelay(deassert);
+ }
+
+ id = vendor << 16 | device;
+ phydev = phy_device_create(bus, 0, id, false, interface);
+ if (phydev)
+ phydev->node = node;
+
+ return phydev;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index f63705e..fffa10f 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1047,6 +1047,11 @@
phydev = phy_device_create(bus, 0, PHY_NCSI_ID, false, interface);
#endif
+#ifdef CONFIG_PHY_ETHERNET_ID
+ if (!phydev)
+ phydev = phy_connect_phy_id(bus, dev, interface);
+#endif
+
#ifdef CONFIG_PHY_XILINX_GMII2RGMII
if (!phydev)
phydev = phy_connect_gmii2rgmii(bus, dev, interface);