sun8i: h3: Add support for the Beelink-x2 STB
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 39cf4c3..f553507 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -482,6 +482,7 @@
sun8i-h2-plus-orangepi-r1.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
+ sun8i-h3-beelink-x2.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
sun8i-h3-nanopi-m1.dtb \
sun8i-h3-nanopi-m1-plus.dtb \
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts
new file mode 100644
index 0000000..25540b7
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -0,0 +1,216 @@
+/*
+ * Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Beelink X2";
+ compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &emac;
+ ethernet1 = &sdiowifi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "beelink-x2:blue:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+
+ red {
+ label = "beelink-x2:red:standby";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+
+ sound_spdif {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ sdiowifi: sdio_wifi@1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB VBUS is always on except for the OTG port */
+ status = "okay";
+ usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+};