* Add dual ethernet support on PM826
* Add support for LXT971 PHY on PM826
* Patch by Tord Andersson, 16 Jan 2003:
Fix flash sector count for TQM8xxL
* Fix I2C EEPROM problem on ICU862 board (would only write the first
16 bytes out of each 32 byte block)
diff --git a/include/configs/PM826.h b/include/configs/PM826.h
index 13d7632..b56da69 100644
--- a/include/configs/PM826.h
+++ b/include/configs/PM826.h
@@ -38,6 +38,8 @@
#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
#define CONFIG_PM826 1 /* ...on a PM8260 module */
+#undef CONFIG_DB_CR826_J30x_ON /* J30x jumpers on D.B. carrier */
+
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
@@ -93,33 +95,50 @@
/*
* select ethernet configuration
*
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
+ * if CONFIG_ETHER_ON_SCC is selected, then
+ * - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
+ * - CONFIG_NET_MULTI must not be defined
+ *
+ * if CONFIG_ETHER_ON_FCC is selected, then
+ * - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
+ * - CONFIG_NET_MULTI must be defined
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
* defined elsewhere (as for the console), or CFG_CMD_NET must be removed
* from CONFIG_COMMANDS to remove support for networking.
*/
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#define CONFIG_NET_MULTI
#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
-#if (CONFIG_ETHER_INDEX == 1)
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_INDEX 1 /* which SCC channel for ethernet */
+
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
/*
* - Rx-CLK is CLK11
* - Tx-CLK is CLK10
+ */
+#define CONFIG_ETHER_ON_FCC1
+# define CFG_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+#ifndef CONFIG_DB_CR826_J30x_ON
+# define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
+#else
+# define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
+#endif
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK14
+ */
+#define CONFIG_ETHER_ON_FCC2
+# define CFG_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+/*
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-#endif /* CONFIG_ETHER_INDEX */
-
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
#define CONFIG_8260_CLKIN 64000000 /* in Hz */