powerpc/t1024qds: Add T1024 QDS board support
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/t102xqds/t102xqds.c b/board/freescale/t102xqds/t102xqds.c
new file mode 100644
index 0000000..97ef95a
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds.c
@@ -0,0 +1,321 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+#include <hwconfig.h>
+#include <asm/mpc85xx_gpio.h>
+#include "../common/qixis.h"
+#include "t102xqds.h"
+#include "t102xqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ char buf[64];
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *const freq[] = {"100", "125", "156.25", "100.0"};
+ int clock;
+ u8 sw = QIXIS_READ(arch);
+
+ printf("Board: %sQDS, ", cpu->name);
+ printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
+ printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+
+#ifdef CONFIG_SDCARD
+ puts("SD/MMC\n");
+#elif CONFIG_SPIFLASH
+ puts("SPI\n");
+#else
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ if (sw < 0x8)
+ printf("vBank: %d\n", sw);
+ else if (sw == 0x8)
+ puts("PromJet\n");
+ else if (sw == 0x9)
+ puts("NAND\n");
+ else if (sw == 0x15)
+ printf("IFC Card\n");
+ else
+ printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+#endif
+
+ printf("FPGA: v%d (%s), build %d",
+ (int)QIXIS_READ(scver), qixis_read_tag(buf),
+ (int)qixis_read_minor());
+ /* the timestamp string contains "\n" at the end */
+ printf(" on %s", qixis_read_time(buf));
+
+ puts("SERDES Reference: ");
+ sw = QIXIS_READ(brdcfg[2]);
+ clock = (sw >> 6) & 3;
+ printf("Clock1=%sMHz ", freq[clock]);
+ clock = (sw >> 4) & 3;
+ printf("Clock2=%sMHz\n", freq[clock]);
+
+ return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int board_mux_lane_to_slot(void)
+{
+ ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_prtcl_s1;
+ u8 brdcfg9;
+
+ srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+
+ brdcfg9 = QIXIS_READ(brdcfg[9]);
+ QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE);
+
+ switch (srds_prtcl_s1) {
+ case 0:
+ /* SerDes1 is not enabled */
+ break;
+ case 0xd5:
+ case 0x5b:
+ case 0x6b:
+ case 0x77:
+ case 0x6f:
+ case 0x7f:
+ QIXIS_WRITE(brdcfg[12], 0x8c);
+ break;
+ case 0x40:
+ QIXIS_WRITE(brdcfg[12], 0xfc);
+ break;
+ case 0xd6:
+ case 0x5a:
+ case 0x6a:
+ case 0x56:
+ QIXIS_WRITE(brdcfg[12], 0x88);
+ break;
+ case 0x47:
+ QIXIS_WRITE(brdcfg[12], 0xcc);
+ break;
+ case 0x46:
+ QIXIS_WRITE(brdcfg[12], 0xc8);
+ break;
+ case 0x95:
+ case 0x99:
+ brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE;
+ QIXIS_WRITE(brdcfg[9], brdcfg9);
+ QIXIS_WRITE(brdcfg[12], 0x8c);
+ break;
+ case 0x116:
+ QIXIS_WRITE(brdcfg[12], 0x00);
+ break;
+ case 0x115:
+ case 0x119:
+ case 0x129:
+ case 0x12b:
+ /* Aurora, PCIe, SGMII, SATA */
+ QIXIS_WRITE(brdcfg[12], 0x04);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes Protocol %d\n",
+ srds_prtcl_s1);
+ return -1;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_PPC_T1024
+static void board_mux_setup(void)
+{
+ u8 brdcfg15;
+
+ brdcfg15 = QIXIS_READ(brdcfg[15]);
+ brdcfg15 &= ~BRDCFG15_DIUSEL_MASK;
+
+ if (hwconfig_arg_cmp("pin_mux", "tdm")) {
+ /* Route QE_TDM multiplexed signals to TDM Riser slot */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM);
+ QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2);
+ } else if (hwconfig_arg_cmp("pin_mux", "ucc")) {
+ /* to UCC (ProfiBus) interface */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC);
+ } else if (hwconfig_arg_cmp("pin_mux", "hdmi")) {
+ /* to DVI (HDMI) encoder */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI);
+ } else if (hwconfig_arg_cmp("pin_mux", "lcd")) {
+ /* to DFP (LCD) encoder */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM |
+ BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD);
+ }
+}
+#endif
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ int flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ if (flash_esel == -1) {
+ /* very unlikely unless something is messed up */
+ puts("Error: Could not find TLB for FLASH BASE\n");
+ flash_esel = 2; /* give our best effort to continue */
+ } else {
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+ }
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+ board_mux_lane_to_slot();
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_64:
+ return 64000000;
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+#define NUM_SRDS_PLL 2
+int misc_init_r(void)
+{
+#ifdef CONFIG_PPC_T1024
+ board_mux_setup();
+#endif
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+
+ return 0;
+}
+
+void qixis_dump_switch(void)
+{
+ int i, nr_of_cfgsw;
+
+ QIXIS_WRITE(cms[0], 0x00);
+ nr_of_cfgsw = QIXIS_READ(cms[1]);
+
+ puts("DIP switch settings dump:\n");
+ for (i = 1; i <= nr_of_cfgsw; i++) {
+ QIXIS_WRITE(cms[0], i);
+ printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
+ }
+}
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+ /* does not provide HW signals for power management */
+ QIXIS_WRITE(pwr_ctl[1], (QIXIS_READ(pwr_ctl[1]) & ~0x2));
+ /* Disable MCKE isolation */
+ gpio_set_value(2, 0);
+ udelay(1);
+}
+#endif