am335x_evm: Rework board_is_foo() checks
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 15e249d..00802b6 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -40,43 +40,10 @@
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-static struct am335x_baseboard_id __attribute__((section (".data"))) header;
-
-static inline int board_is_bone(void)
-{
- return !strncmp(header.name, "A335BONE", HDR_NAME_LEN);
-}
-
-static inline int board_is_bone_lt(void)
-{
- return !strncmp(header.name, "A335BNLT", HDR_NAME_LEN);
-}
-
-static inline int board_is_evm_sk(void)
-{
- return !strncmp("A335X_SK", header.name, HDR_NAME_LEN);
-}
-
-static inline int board_is_idk(void)
-{
- return !strncmp(header.config, "SKU#02", 6);
-}
-
-static int __maybe_unused board_is_gp_evm(void)
-{
- return !strncmp("A33515BB", header.name, 8);
-}
-
-int board_is_evm_15_or_later(void)
-{
- return (!strncmp("A33515BB", header.name, 8) &&
- strncmp("1.5", header.version, 3) <= 0);
-}
-
/*
* Read header information from EEPROM into global structure.
*/
-static int read_eeprom(void)
+static int read_eeprom(struct am335x_baseboard_id *header)
{
/* Check if baseboard eeprom is available */
if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
@@ -86,28 +53,28 @@
}
/* read the eeprom using i2c */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)&header,
- sizeof(header))) {
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
+ sizeof(struct am335x_baseboard_id))) {
puts("Could not read the EEPROM; something fundamentally"
" wrong on the I2C bus.\n");
return -EIO;
}
- if (header.magic != 0xEE3355AA) {
+ if (header->magic != 0xEE3355AA) {
/*
* read the eeprom using i2c again,
* but use only a 1 byte address
*/
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1,
- (uchar *)&header, sizeof(header))) {
+ if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
+ sizeof(struct am335x_baseboard_id))) {
puts("Could not read the EEPROM; something "
"fundamentally wrong on the I2C bus.\n");
return -EIO;
}
- if (header.magic != 0xEE3355AA) {
+ if (header->magic != 0xEE3355AA) {
printf("Incorrect magic number (0x%x) in EEPROM\n",
- header.magic);
+ header->magic);
return -EINVAL;
}
}
@@ -281,12 +248,14 @@
*/
void s_init(void)
{
+#ifdef CONFIG_SPL_BUILD
+ struct am335x_baseboard_id header;
+
/*
* Save the boot parameters passed from romcode.
* We cannot delay the saving further than this,
* to prevent overwrites.
*/
-#ifdef CONFIG_SPL_BUILD
save_omap_boot_params();
#endif
@@ -335,11 +304,11 @@
/* Initalize the board header */
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- if (read_eeprom() < 0)
+ if (read_eeprom(&header) < 0)
puts("Could not get board ID.\n");
enable_board_pin_mux(&header);
- if (board_is_evm_sk()) {
+ if (board_is_evm_sk(&header)) {
/*
* EVM SK 1.2A and later use gpio0_7 to enable DDR3.
* This is safe enough to do on older revs.
@@ -348,15 +317,15 @@
gpio_direction_output(GPIO_DDR_VTT_EN, 1);
}
- if (board_is_evm_sk())
+ if (board_is_evm_sk(&header))
config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
- else if (board_is_bone_lt())
+ else if (board_is_bone_lt(&header))
config_ddr(400, MT41K256M16HA125E_IOCTRL_VALUE,
&ddr3_beagleblack_data,
&ddr3_beagleblack_cmd_ctrl_data,
&ddr3_beagleblack_emif_reg_data, 0);
- else if (board_is_evm_15_or_later())
+ else if (board_is_evm_15_or_later(&header))
config_ddr(303, MT41J512M8RH125_IOCTRL_VALUE, &ddr3_evm_data,
&ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0);
else
@@ -370,10 +339,6 @@
*/
int board_init(void)
{
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- if (read_eeprom() < 0)
- puts("Could not get board ID.\n");
-
gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
gpmc_init();
@@ -386,6 +351,10 @@
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
char safe_string[HDR_NAME_LEN + 1];
+ struct am335x_baseboard_id header;
+
+ if (read_eeprom(&header) < 0)
+ puts("Could not get board ID.\n");
/* Now set variables based on the header. */
strncpy(safe_string, (char *)header.name, sizeof(header.name));
@@ -450,6 +419,7 @@
int rv, n = 0;
uint8_t mac_addr[6];
uint32_t mac_hi, mac_lo;
+ __maybe_unused struct am335x_baseboard_id header;
/* try reading mac address from efuse */
mac_lo = readl(&cdev->macid0l);
@@ -471,7 +441,11 @@
}
#ifdef CONFIG_DRIVER_TI_CPSW
- if (board_is_bone() || board_is_bone_lt() || board_is_idk()) {
+ if (read_eeprom(&header) < 0)
+ puts("Could not get board ID.\n");
+
+ if (board_is_bone(&header) || board_is_bone_lt(&header) ||
+ board_is_idk(&header)) {
writel(MII_MODE_ENABLE, &cdev->miisel);
cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
PHY_INTERFACE_MODE_MII;
@@ -500,7 +474,7 @@
#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
#define AR8051_RGMII_TX_CLK_DLY 0x100
- if (board_is_evm_sk() || board_is_gp_evm()) {
+ if (board_is_evm_sk(&header) || board_is_gp_evm(&header)) {
const char *devname;
devname = miiphy_get_current_dev();
diff --git a/board/ti/am335x/board.h b/board/ti/am335x/board.h
index 9fea1f1..bc700d5 100644
--- a/board/ti/am335x/board.h
+++ b/board/ti/am335x/board.h
@@ -29,6 +29,37 @@
char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
};
+static inline int board_is_bone(struct am335x_baseboard_id *header)
+{
+ return !strncmp(header->name, "A335BONE", HDR_NAME_LEN);
+}
+
+static inline int board_is_bone_lt(struct am335x_baseboard_id *header)
+{
+ return !strncmp(header->name, "A335BNLT", HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_sk(struct am335x_baseboard_id *header)
+{
+ return !strncmp("A335X_SK", header->name, HDR_NAME_LEN);
+}
+
+static inline int board_is_idk(struct am335x_baseboard_id *header)
+{
+ return !strncmp(header->config, "SKU#02", 6);
+}
+
+static inline int board_is_gp_evm(struct am335x_baseboard_id *header)
+{
+ return !strncmp("A33515BB", header->name, HDR_NAME_LEN);
+}
+
+static inline int board_is_evm_15_or_later(struct am335x_baseboard_id *header)
+{
+ return (board_is_gp_evm(header) &&
+ strncmp("1.5", header->version, 3) <= 0);
+}
+
/*
* We have three pin mux functions that must exist. We must be able to enable
* uart0, for initial output and i2c0 to read the main EEPROM. We then have a
diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
index 0283708..2e09d98 100644
--- a/board/ti/am335x/mux.c
+++ b/board/ti/am335x/mux.c
@@ -262,13 +262,13 @@
void enable_board_pin_mux(struct am335x_baseboard_id *header)
{
/* Do board-specific muxes. */
- if (!strncmp(header->name, "A335BONE", HDR_NAME_LEN)) {
+ if (board_is_bone(header)) {
/* Beaglebone pinmux */
configure_module_pin_mux(i2c1_pin_mux);
configure_module_pin_mux(mii1_pin_mux);
configure_module_pin_mux(mmc0_pin_mux);
configure_module_pin_mux(mmc1_pin_mux);
- } else if (!strncmp(header->config, "SKU#01", 6)) {
+ } else if (board_is_gp_evm(header)) {
/* General Purpose EVM */
unsigned short profile = detect_daughter_board_profile();
configure_module_pin_mux(rgmii1_pin_mux);
@@ -283,7 +283,7 @@
configure_module_pin_mux(mmc1_pin_mux);
configure_module_pin_mux(spi0_pin_mux);
}
- } else if (!strncmp(header->config, "SKU#02", 6)) {
+ } else if (board_is_idk(header)) {
/*
* Industrial Motor Control (IDK)
* note: IDK console is on UART3 by default.
@@ -292,13 +292,13 @@
*/
configure_module_pin_mux(mii1_pin_mux);
configure_module_pin_mux(mmc0_no_cd_pin_mux);
- } else if (!strncmp(header->name, "A335X_SK", HDR_NAME_LEN)) {
+ } else if (board_is_evm_sk(header)) {
/* Starter Kit EVM */
configure_module_pin_mux(i2c1_pin_mux);
configure_module_pin_mux(gpio0_7_pin_mux);
configure_module_pin_mux(rgmii1_pin_mux);
configure_module_pin_mux(mmc0_pin_mux_sk_evm);
- } else if (!strncmp(header->name, "A335BNLT", HDR_NAME_LEN)) {
+ } else if (board_is_bone_lt(header)) {
/* Beaglebone LT pinmux */
configure_module_pin_mux(i2c1_pin_mux);
configure_module_pin_mux(mii1_pin_mux);