Convert CONFIG_AM335X_USB0 et al to Kconfig
This converts the following to Kconfig:
CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
We do this by introducing specific options for static configuration of
USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the
enum value being used. Furthermore, with how the code is used now we do
not need to have OTG mode exposed as an option here, so remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/mach-omap2/am33xx/Kconfig b/arch/arm/mach-omap2/am33xx/Kconfig
index 1402376..b8e115d 100644
--- a/arch/arm/mach-omap2/am33xx/Kconfig
+++ b/arch/arm/mach-omap2/am33xx/Kconfig
@@ -280,3 +280,35 @@
image, this area is no longer used, and can be reclaimed
for run time use by the boot image.
endif
+
+config AM335X_USB0
+ bool "Static mode configuration for USB0 in SPL"
+ depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
+
+choice
+ prompt "USB0 port configuration"
+ depends on AM335X_USB0
+
+config AM335X_USB0_HOST
+ bool "Port is used in host mode"
+
+config AM335X_USB0_PERIPHERAL
+ bool "Port is used in peripheral mode"
+
+endchoice
+
+config AM335X_USB1
+ bool "Static mode configuration for USB1 in SPL"
+ depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
+
+choice
+ prompt "USB1 port configuration"
+ depends on AM335X_USB1
+
+config AM335X_USB1_HOST
+ bool "Port is used in host mode"
+
+config AM335X_USB1_PERIPHERAL
+ bool "Port is used in peripheral mode"
+
+endchoice
diff --git a/arch/arm/mach-omap2/am33xx/board.c b/arch/arm/mach-omap2/am33xx/board.c
index bcc907c..5175eb0 100644
--- a/arch/arm/mach-omap2/am33xx/board.c
+++ b/arch/arm/mach-omap2/am33xx/board.c
@@ -241,14 +241,14 @@
};
U_BOOT_DRVINFOS(am33xx_usbs) = {
-#if CONFIG_AM335X_USB0_MODE == MUSB_PERIPHERAL
+#ifdef CONFIG_AM335X_USB0_PERIPHERAL
{ "ti-musb-peripheral", &usb0 },
-#elif CONFIG_AM335X_USB0_MODE == MUSB_HOST
+#elif defined(CONFIG_AM335X_USB0_HOST)
{ "ti-musb-host", &usb0 },
#endif
-#if CONFIG_AM335X_USB1_MODE == MUSB_PERIPHERAL
+#ifdef CONFIG_AM335X_USB1_PERIPHERAL
{ "ti-musb-peripheral", &usb1 },
-#elif CONFIG_AM335X_USB1_MODE == MUSB_HOST
+#elif defined(CONFIG_AM335X_USB1_HOST)
{ "ti-musb-host", &usb1 },
#endif
};
diff --git a/configs/am335x_evm_defconfig b/configs/am335x_evm_defconfig
index 535b269..497127d 100644
--- a/configs/am335x_evm_defconfig
+++ b/configs/am335x_evm_defconfig
@@ -4,6 +4,9 @@
CONFIG_TI_COMMON_CMD_OPTIONS=y
CONFIG_DEFAULT_DEVICE_TREE="am335x-evm"
CONFIG_AM33XX=y
+CONFIG_AM335X_USB0=y
+CONFIG_AM335X_USB0_PERIPHERAL=y
+CONFIG_AM335X_USB1=y
CONFIG_SPL=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_TIMESTAMP=y
diff --git a/configs/am335x_guardian_defconfig b/configs/am335x_guardian_defconfig
index ca3d01a..f8cc073 100644
--- a/configs/am335x_guardian_defconfig
+++ b/configs/am335x_guardian_defconfig
@@ -10,6 +10,9 @@
CONFIG_DEFAULT_DEVICE_TREE="am335x-guardian"
CONFIG_AM33XX=y
CONFIG_TARGET_AM335X_GUARDIAN=y
+CONFIG_AM335X_USB0=y
+CONFIG_AM335X_USB0_PERIPHERAL=y
+CONFIG_AM335X_USB1=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 9070845..4db04ff 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -202,18 +202,6 @@
*/
/*
- * USB configuration. We enable MUSB support, both for host and for
- * gadget. We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each. Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
-/*
* Disable MMC DM for SPL build and can be re-enabled after adding
* DM support in SPL
*/
diff --git a/include/configs/am335x_guardian.h b/include/configs/am335x_guardian.h
index 10a95a1..608a22d 100644
--- a/include/configs/am335x_guardian.h
+++ b/include/configs/am335x_guardian.h
@@ -129,9 +129,4 @@
#endif /* CONFIG_MTD_RAW_NAND */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
#endif /* ! __CONFIG_AM335X_GUARDIAN_H */
diff --git a/include/configs/baltos.h b/include/configs/baltos.h
index f4ab664..b881d8c 100644
--- a/include/configs/baltos.h
+++ b/include/configs/baltos.h
@@ -214,18 +214,6 @@
#endif
#endif
-/*
- * USB configuration. We enable MUSB support, both for host and for
- * gadget. We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each. Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_HOST
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_OTG
-
/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
#define GPMC_NAND_ECC_LP_x8_LAYOUT 1
diff --git a/include/configs/chiliboard.h b/include/configs/chiliboard.h
index fe49627..aa2a07e 100644
--- a/include/configs/chiliboard.h
+++ b/include/configs/chiliboard.h
@@ -127,10 +127,6 @@
#define CONFIG_SYS_NAND_ECCBYTES 14
/* NAND: SPL related configs */
-/* USB configuration */
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
/*
* Disable MMC DM for SPL build and can be re-enabled after adding
* DM support in SPL
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index c3a04c2..bfadf4a 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -104,13 +104,6 @@
*/
#ifndef CONFIG_SPL_BUILD
-/*
- * USB configuration
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
/* USB DRACO ID as default */
#define CONFIG_USBD_HS