keymile: Factor out common includes again
Not that the Kconfig conversion of a lot of variables is done, we can
factor out the common include files for the keymile boards again (which
now contain hardly any #ifdef logic at all).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
diff --git a/include/configs/km/km-mpc8309.h b/include/configs/km/km-mpc8309.h
new file mode 100644
index 0000000..e89b7af
--- /dev/null
+++ b/include/configs/km/km-mpc8309.h
@@ -0,0 +1,137 @@
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_QE 1 /* Has QE */
+
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 66000000
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define CONFIG_83XX_PCICLK 66000000
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0 \
+ | SICR_1_UART1_UART1RTS \
+ | SICR_1_I2C_CKSTOP \
+ | SICR_1_IRQ_A_IRQ \
+ | SICR_1_IRQ_B_IRQ \
+ | SICR_1_GPIO_A_GPIO \
+ | SICR_1_GPIO_B_GPIO \
+ | SICR_1_GPIO_C_GPIO \
+ | SICR_1_GPIO_D_GPIO \
+ | SICR_1_GPIO_E_GPIO \
+ | SICR_1_GPIO_F_GPIO \
+ | SICR_1_USB_A_UART2S \
+ | SICR_1_USB_B_UART2RTS \
+ | SICR_1_FEC1_FEC1 \
+ | SICR_1_FEC2_FEC2 \
+ )
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0 \
+ | SICR_2_FEC3_FEC3 \
+ | SICR_2_HDLC1_A_HDLC1 \
+ | SICR_2_ELBC_A_LA \
+ | SICR_2_ELBC_B_LCLK \
+ | SICR_2_HDLC2_A_HDLC2 \
+ | SICR_2_USB_D_GPIO \
+ | SICR_2_PCI_PCI \
+ | SICR_2_HDLC1_B_HDLC1 \
+ | SICR_2_HDLC1_C_HDLC1 \
+ | SICR_2_HDLC2_B_GPIO \
+ | SICR_2_HDLC2_C_HDLC2 \
+ | SICR_2_QUIESCE_B \
+ )
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1 0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_RD_NEVER | \
+ CSCONFIG_ODT_WR_ONLY_CURRENT | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR 0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100