powerpc/QorIQ: fix network frame manager TBI PHY address settings
TBI PHY address (TBIPA) register has been set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c
So remove the duplicate code on QorIQ frame manager Ethernet related
platforms, which include Hydra board, P4080DS board and P2041rdb board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/board/freescale/corenet_ds/eth_hydra.c b/board/freescale/corenet_ds/eth_hydra.c
index a7a5e13..962f380 100644
--- a/board/freescale/corenet_ds/eth_hydra.c
+++ b/board/freescale/corenet_ds/eth_hydra.c
@@ -377,7 +377,6 @@
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
@@ -387,13 +386,6 @@
initialize_lane_to_slot();
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
/* We want to use the PIXIS to configure MUX routing, not GPIOs. */
setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL);
diff --git a/board/freescale/corenet_ds/eth_p4080.c b/board/freescale/corenet_ds/eth_p4080.c
index 7ff00d1..1f00c14 100644
--- a/board/freescale/corenet_ds/eth_p4080.c
+++ b/board/freescale/corenet_ds/eth_p4080.c
@@ -301,7 +301,6 @@
{
#ifdef CONFIG_FMAN_ENET
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
int i;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
@@ -327,13 +326,6 @@
SLOT5, /* 17 - Bank 3:D */
};
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
/* Initialize the mdio_mux array so we can recognize empty elements */
for (i = 0; i < NUM_FM_PORTS; i++)
mdio_mux[i] = EMI_NONE;
diff --git a/board/freescale/p2041rdb/eth.c b/board/freescale/p2041rdb/eth.c
index 0a1dfa7..4b0d577 100644
--- a/board/freescale/p2041rdb/eth.c
+++ b/board/freescale/p2041rdb/eth.c
@@ -139,7 +139,6 @@
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
- struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
@@ -149,13 +148,6 @@
initialize_lane_to_slot();
- /*
- * Set TBIPA on FM1@DTSEC1. This is needed for configurations
- * where FM1@DTSEC1 isn't used directly, since it provides
- * MDIO for other ports.
- */
- out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
dtsec_mdio_info.regs =
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;