pinctrl: stm32: display bias information for all pins

Display the bias information for input gpios or AF configuration,
and not only for output pin, as described in Reference manual
(Table 81. Port bit configuration table).

Fixes: da7a0bb1f279 ("pinctrl: stm32: add information on pin configuration")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
diff --git a/drivers/pinctrl/pinctrl_stm32.c b/drivers/pinctrl/pinctrl_stm32.c
index dbea995..262b2c3 100644
--- a/drivers/pinctrl/pinctrl_stm32.c
+++ b/drivers/pinctrl/pinctrl_stm32.c
@@ -48,15 +48,15 @@
 	"alt function",
 };
 
-static const char * const pinmux_output[] = {
-	[STM32_GPIO_PUPD_NO] = "bias-disable",
-	[STM32_GPIO_PUPD_UP] = "bias-pull-up",
-	[STM32_GPIO_PUPD_DOWN] = "bias-pull-down",
+static const char * const pinmux_bias[] = {
+	[STM32_GPIO_PUPD_NO] = "",
+	[STM32_GPIO_PUPD_UP] = "pull-up",
+	[STM32_GPIO_PUPD_DOWN] = "pull-down",
 };
 
 static const char * const pinmux_input[] = {
-	[STM32_GPIO_OTYPE_PP] = "drive-push-pull",
-	[STM32_GPIO_OTYPE_OD] = "drive-open-drain",
+	[STM32_GPIO_OTYPE_PP] = "push-pull",
+	[STM32_GPIO_OTYPE_OD] = "open-drain",
 };
 
 static int stm32_pinctrl_get_af(struct udevice *dev, unsigned int offset)
@@ -213,6 +213,7 @@
 	dev_dbg(dev, "selector = %d gpio_idx = %d mode = %d\n",
 		selector, gpio_idx, mode);
 	priv = dev_get_priv(gpio_dev);
+	pupd = (readl(&priv->regs->pupdr) >> (gpio_idx * 2)) & PUPD_MASK;
 
 
 	switch (mode) {
@@ -224,20 +225,19 @@
 		break;
 	case GPIOF_FUNC:
 		af_num = stm32_pinctrl_get_af(gpio_dev, gpio_idx);
-		snprintf(buf, size, "%s %d", pinmux_mode[mode], af_num);
+		snprintf(buf, size, "%s %d %s", pinmux_mode[mode], af_num,
+			 pinmux_bias[pupd]);
 		break;
 	case GPIOF_OUTPUT:
-		pupd = (readl(&priv->regs->pupdr) >> (gpio_idx * 2)) &
-		       PUPD_MASK;
 		snprintf(buf, size, "%s %s %s",
-			 pinmux_mode[mode], pinmux_output[pupd],
+			 pinmux_mode[mode], pinmux_bias[pupd],
 			 label ? label : "");
 		break;
 	case GPIOF_INPUT:
 		otype = (readl(&priv->regs->otyper) >> gpio_idx) & OTYPE_MSK;
-		snprintf(buf, size, "%s %s %s",
+		snprintf(buf, size, "%s %s %s %s",
 			 pinmux_mode[mode], pinmux_input[otype],
-			 label ? label : "");
+			 pinmux_bias[pupd], label ? label : "");
 		break;
 	}