arm: kirkwood: Add support for ZyXEL NSA325 board
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 6e9c5f0..81c455a 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -66,6 +66,7 @@
kirkwood-ns2max.dtb \
kirkwood-ns2mini.dtb \
kirkwood-nsa310s.dtb \
+ kirkwood-nsa325.dtb \
kirkwood-openrd-base.dtb \
kirkwood-openrd-client.dtb \
kirkwood-openrd-ultimate.dtb \
diff --git a/arch/arm/dts/kirkwood-6282.dtsi b/arch/arm/dts/kirkwood-6282.dtsi
new file mode 100644
index 0000000..e732c50
--- /dev/null
+++ b/arch/arm/dts/kirkwood-6282.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ mbus@f1000000 {
+ pciec: pcie@82000000 {
+ compatible = "marvell,kirkwood-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
+ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 1.0 MEM */
+ 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 1.0 IO */>;
+
+ pcie0: pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-names = "intx", "error";
+ interrupts = <9>, <44>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+ <0 0 0 2 &pcie0_intc 1>,
+ <0 0 0 3 &pcie0_intc 2>,
+ <0 0 0 4 &pcie0_intc 3>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 2>;
+ status = "disabled";
+
+ pcie0_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ pcie1: pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x00044000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+ 0x81000000 0 0 0x81000000 0x2 0 1 0>;
+ bus-range = <0x00 0xff>;
+ interrupt-names = "intx", "error";
+ interrupts = <10>, <45>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+ <0 0 0 2 &pcie1_intc 1>,
+ <0 0 0 3 &pcie1_intc 2>,
+ <0 0 0 4 &pcie1_intc 3>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gate_clk 18>;
+ status = "disabled";
+
+ pcie1_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+ };
+ };
+ ocp@f1000000 {
+
+ pinctrl: pin-controller@10000 {
+ compatible = "marvell,88f6282-pinctrl";
+
+ pmx_sata0: pmx-sata0 {
+ marvell,pins = "mpp5", "mpp21", "mpp23";
+ marvell,function = "sata0";
+ };
+ pmx_sata1: pmx-sata1 {
+ marvell,pins = "mpp4", "mpp20", "mpp22";
+ marvell,function = "sata1";
+ };
+
+ /*
+ * Default I2C1 pinctrl setting on mpp36/mpp37,
+ * overwrite marvell,pins on board level if required.
+ */
+ pmx_twsi1: pmx-twsi1 {
+ marvell,pins = "mpp36", "mpp37";
+ marvell,function = "twsi1";
+ };
+
+ pmx_sdio: pmx-sdio {
+ marvell,pins = "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "sdio";
+ };
+ };
+
+ thermal: thermal@10078 {
+ compatible = "marvell,kirkwood-thermal";
+ reg = <0x10078 0x4>;
+ status = "okay";
+ };
+
+ rtc: rtc@10300 {
+ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <53>;
+ clocks = <&gate_clk 7>;
+ };
+
+ i2c1: i2c@11100 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <32>;
+ clock-frequency = <100000>;
+ clocks = <&gate_clk 7>;
+ pinctrl-0 = <&pmx_twsi1>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ sata: sata@80000 {
+ compatible = "marvell,orion-sata";
+ reg = <0x80000 0x5000>;
+ interrupts = <21>;
+ clocks = <&gate_clk 14>, <&gate_clk 15>;
+ clock-names = "0", "1";
+ phys = <&sata_phy0>, <&sata_phy1>;
+ phy-names = "port0", "port1";
+ status = "disabled";
+ };
+
+ sdio: mvsdio@90000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0x90000 0x200>;
+ interrupts = <28>;
+ clocks = <&gate_clk 4>;
+ pinctrl-0 = <&pmx_sdio>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/kirkwood-nsa325.dts b/arch/arm/dts/kirkwood-nsa325.dts
new file mode 100644
index 0000000..efc57cf
--- /dev/null
+++ b/arch/arm/dts/kirkwood-nsa325.dts
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Device tree file for the Zyxel NSA 325 NAS box.
+ *
+ * Copyright (c) 2015, Hans Ulli Kroll <ulli.kroll@googlemail.com>
+ *
+ *
+ * Based upon the board setup file created by Peter Schildmann
+ */
+
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/ {
+ model = "ZyXEL NSA325";
+ compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pinctrl-names = "default";
+
+ pmx_led_hdd2_green: pmx-led-hdd2-green {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd2_red: pmx-led-hdd2-red {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_mcu_data: pmx-mcu-data {
+ marvell,pins = "mpp14";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_green: pmx-led-usb-green {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_mcu_clk: pmx-mcu-clk {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_mcu_act: pmx-mcu-act {
+ marvell,pins = "mpp17";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_green: pmx-led-sys-green {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_orange: pmx-led-sys-orange {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd1_green: pmx-led-hdd1-green {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd1_red: pmx-led-hdd1-red {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ pmx_htp: pmx-htp {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * Buzzer needs to be switched at around 1kHz so is
+ * not compatible with the gpio-beeper driver.
+ */
+ pmx_buzzer: pmx-buzzer {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ pmx_vid_b1: pmx-vid-b1 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_resume_data: pmx-power-resume-data {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_resume_clk: pmx-power-resume-clk {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+
+ pmx_pwr_sata1: pmx-pwr-sata1 {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+
+ /* This board uses the pcf8563 RTC instead of the SoC RTC */
+ rtc@10300 {
+ status = "disabled";
+ };
+
+ i2c@11000 {
+ status = "okay";
+
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_pwr_sata1>;
+ pinctrl-names = "default";
+
+ usb0_power: regulator@1 {
+ enable-active-high;
+ };
+
+ sata1_power: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red
+ &pmx_led_usb_green
+ &pmx_led_sys_green &pmx_led_sys_orange
+ &pmx_led_copy_green &pmx_led_copy_red
+ &pmx_led_hdd1_green &pmx_led_hdd1_red>;
+ pinctrl-names = "default";
+
+ green-sys {
+ label = "nsa325:green:sys";
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ };
+ orange-sys {
+ label = "nsa325:orange:sys";
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd1 {
+ label = "nsa325:green:hdd1";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd1 {
+ label = "nsa325:red:hdd1";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd2 {
+ label = "nsa325:green:hdd2";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd2 {
+ label = "nsa325:red:hdd2";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+ green-usb {
+ label = "nsa325:green:usb";
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+ green-copy {
+ label = "nsa325:green:copy";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+ red-copy {
+ label = "nsa325:red:copy";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* The following pins are currently not assigned to a driver,
+ some of them should be configured as inputs.
+ pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act
+ &pmx_htp &pmx_vid_b1
+ &pmx_power_resume_data &pmx_power_resume_clk>; */
+ };
+
+};
+
+&mdio {
+ status = "okay";
+ ethphy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/kirkwood-nsa3x0-common.dtsi b/arch/arm/dts/kirkwood-nsa3x0-common.dtsi
new file mode 100644
index 0000000..a21c50d
--- /dev/null
+++ b/arch/arm/dts/kirkwood-nsa3x0-common.dtsi
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "ZyXEL NSA310";
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+
+ pmx_usb_power: pmx-usb-power {
+ marvell,pins = "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_pwr_off: pmx-pwr-off {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+
+ pmx_btn_reset: pmx-btn-reset {
+ marvell,pins = "mpp36";
+ marvell,function = "gpio";
+ };
+
+ pmx_btn_copy: pmx-btn-copy {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+
+ pmx_btn_power: pmx-btn-power {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_copy_green: pmx-led-copy-green {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_copy_red: pmx-led-copy-red {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ };
+
+ serial@12000 {
+ status = "okay";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_pwr_off>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>;
+ pinctrl-names = "default";
+
+ power {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ copy {
+ label = "Copy Button";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ };
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power>;
+ pinctrl-names = "default";
+
+ usb0_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x0100000>;
+ };
+ partition@100000 {
+ label = "uboot_env";
+ reg = <0x0100000 0x0080000>;
+ };
+ partition@180000 {
+ label = "key_store";
+ reg = <0x0180000 0x0080000>;
+ };
+ partition@200000 {
+ label = "info";
+ reg = <0x0200000 0x0080000>;
+ };
+ partition@280000 {
+ label = "etc";
+ reg = <0x0280000 0x0a00000>;
+ };
+ partition@c80000 {
+ label = "kernel_1";
+ reg = <0x0c80000 0x0a00000>;
+ };
+ partition@1680000 {
+ label = "rootfs1";
+ reg = <0x1680000 0x2fc0000>;
+ };
+ partition@4640000 {
+ label = "kernel_2";
+ reg = <0x4640000 0x0a00000>;
+ };
+ partition@5040000 {
+ label = "rootfs2";
+ reg = <0x5040000 0x2fc0000>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 54027cc..c2fff84 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -133,6 +133,12 @@
select KW88F6192
select KIRKWOOD_COMMON
+config TARGET_NSA325
+ bool "ZyXEL NSA325"
+ select FEROCEON_88FR131
+ select KW88F6281
+ select KIRKWOOD_COMMON
+
config TARGET_SBx81LIFKW
bool "Allied Telesis SBx81GS24/SBx81GT40/SBx81XS6/SBx81XS16"
select FEROCEON_88FR131
@@ -177,6 +183,7 @@
source "board/Seagate/goflexhome/Kconfig"
source "board/Seagate/nas220/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
+source "board/zyxel/nsa325/Kconfig"
source "board/alliedtelesis/SBx81LIFKW/Kconfig"
source "board/alliedtelesis/SBx81LIFXCAT/Kconfig"