Merge with /home/wd/git/u-boot/jon_loeliger
diff --git a/CHANGELOG b/CHANGELOG
index 50a8689..f1484ee 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -1,6 +1,7 @@
======================================================================
Changes for U-Boot 1.1.3:
======================================================================
+
* Patch by Jon Loeliger
Fix style issues primarily in 85xx and 83xx boards.
- C++ comments
@@ -9,43 +10,49 @@
- Excessive amount of empty lines
- Trailing empty lines
-* Patch by Ron Alder, 11 July 2005
+* Patch by Ron Alder, 11 Jul 2005
Add Xianghua Xiao and Lunsheng Wang's support for the
GDA MPC8540 EVAL board.
* Patch by Eran Liberty
Add support for the Freescale MPC8349ADS board.
-* Patch by Jon Loeliger, 2005-07-25
+* Patch by Jon Loeliger, 25 Jul 2005
Move the TSEC driver out of cpu/mpc85xx as it will be shared
by the upcoming mpc83xx family as well.
-* Patch by Jon Loeliger, 2005-05-05
+* Patch by Jon Loeliger, 05 May 2005
Implemented support for MPC8548CDS board.
Added DDR II support based on SPD values for MPC85xx boards.
This roll-up patch also includes bugfies for the previously
published patches:
DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O
-* Patch by Jon Loeliger, 2005-Feb-10
+* Patch by Jon Loeliger, 10 Feb 2005
Add config option CONFIG_HAS_FEC calling out 8540 FEC features.
-* Patch by Jon Loeliger, Kumar Gala, 2005-02-08
+* Patch by Jon Loeliger, Kumar Gala, 08 Feb 2005
For MPC85xxCDS:
Adds Relaxed Timing TRLX bit to FLASH ORx regs to allow
for faster flash parts.
Add documentation for BR/OR for FLASH.
-* Patch by Jon Loeliger 2005-02-08
+* Patch by Jon Loeliger 08 Feb 2005
Determine L2 Cache size dynamically on 85XX boards.
-* Patch by Jon Loeliger, Kumar Gala 2005-02-08
+* Patch by Jon Loeliger, Kumar Gala 08 Feb 2005
- Convert the CPM2 based functionality to use new CONFIG_CPM2
option rather than a myriad of CONFIG_MPC8560-like variants.
Applies to MPC85xx and MPC8260 boards, includes stxgp3 and sbc8560.
Eliminates the CONFIG_MPC8560 option entirely. Distributes the
new CONFIG_CPM2 option to each 8260 board.
+* Add support for MicroSys PM856 board
+ Patch by Josef Wagner, 03 Aug 2005
+
+* Minor fixes to PM854 board
+ Patch by Josef Wagner, 03 Aug 2005
+
* Adjust configuration of XENIAX board
(chip select and GPIO required for USB operation)
@@ -53,7 +60,7 @@
routed to the Watchdog handler
Patch by Eugene Surovegin, 18 Jun 2005
-* (re)enabled scsi commands do_scsi() and do_scsiboot()
+* (re)enabled scsi commands do_scsi() and do_scsiboot()
Patch by Denis Peter, 06 Dec 2004
* Fix endianess problem in TFTP / NFS default filenames
diff --git a/MAKEALL b/MAKEALL
index e221de9..2d0c096 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -121,10 +121,9 @@
#########################################################################
LIST_85xx=" \
-
MPC8540ADS MPC8540EVAL MPC8541CDS MPC8548CDS \
- MPC8555CDS MPC8560ADS PM854 sbc8540 \
- sbc8560 stxgp3 TQM8540 \
+ MPC8555CDS MPC8560ADS PM854 PM856 \
+ sbc8540 sbc8560 stxgp3 TQM8540 \
"
#########################################################################
diff --git a/Makefile b/Makefile
index 92b7534..8fb600d 100644
--- a/Makefile
+++ b/Makefile
@@ -1244,6 +1244,9 @@
PM854_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx pm854
+PM856_config: unconfig
+ @./mkconfig $(@:_config=) ppc mpc85xx pm856
+
sbc8540_config \
sbc8540_33_config \
sbc8540_66_config: unconfig
diff --git a/board/pm854/Makefile b/board/pm854/Makefile
index c6b4cae..7828166 100644
--- a/board/pm854/Makefile
+++ b/board/pm854/Makefile
@@ -25,7 +25,7 @@
LIB = lib$(BOARD).a
-OBJS := $(BOARD).o flash.o
+OBJS := $(BOARD).o
SOBJS := init.o
#SOBJS :=
diff --git a/board/pm856/Makefile b/board/pm856/Makefile
new file mode 100644
index 0000000..5d8ea34
--- /dev/null
+++ b/board/pm856/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS := $(BOARD).o
+SOBJS := init.o
+#SOBJS :=
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) crv $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
diff --git a/board/pm856/config.mk b/board/pm856/config.mk
new file mode 100644
index 0000000..1f98b33
--- /dev/null
+++ b/board/pm856/config.mk
@@ -0,0 +1,33 @@
+# Copyright 2004 Freescale Semiconductor.
+# Modified by Xianghua Xiao, X.Xiao@motorola.com
+# (C) Copyright 2002,2003 Motorola Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# PM856 board
+# default CCARBAR is at 0xff700000
+# assume U-Boot is less than 0.5MB
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8560=1
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
diff --git a/board/pm856/init.S b/board/pm856/init.S
new file mode 100644
index 0000000..ade5d6e
--- /dev/null
+++ b/board/pm856/init.S
@@ -0,0 +1,263 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * Copyright (C) 2002,2003, Motorola Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define entry_start \
+ mflr r1 ; \
+ bl 0f ;
+
+#define entry_end \
+0: mflr r0 ; \
+ mtlr r1 ; \
+ blr ;
+
+
+ .section .bootpg, "ax"
+ .globl tlb1_entry
+tlb1_entry:
+ entry_start
+
+ /*
+ * Number of TLB0 and TLB1 entries in the following table
+ */
+ .long 13
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+ /*
+ * TLB0 4K Non-cacheable, guarded
+ * 0xff700000 4K Initial CCSRBAR mapping
+ *
+ * This ends up at a TLB0 Index==0 entry, and must not collide
+ * with other TLB0 Entries.
+ */
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+ /*
+ * TLB0 16K Cacheable, non-guarded
+ * 0xd001_0000 16K Temporary Global data for initialization
+ *
+ * Use four 4K TLB0 entries. These entries must be cacheable
+ * as they provide the bootstrap memory before the memory
+ * controler and real memory have been configured.
+ *
+ * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+ * and must not collide with other TLB0 entries.
+ */
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+
+ /*
+ * TLB 0: 64M Non-cacheable, guarded
+ * 0xfc000000 64M FLASH (8,16,32 or 64 MB)
+ * Out of reset this entry is only 4K.
+ */
+ .long TLB1_MAS0(1, 0, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(0xfc000000), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(0xfc000000), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 1: 256M Non-cacheable, guarded
+ * 0x80000000 256M PCI1 MEM First half
+ */
+ .long TLB1_MAS0(1, 1, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 2: 256M Non-cacheable, guarded
+ * 0x90000000 256M PCI1 MEM Second half
+ */
+ .long TLB1_MAS0(1, 2, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+ 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 3: 256M Non-cacheable, guarded
+ * 0xc0000000 256M Rapid IO MEM First half
+ */
+ .long TLB1_MAS0(1, 3, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 4: 256M Non-cacheable, guarded
+ * 0xd0000000 256M Rapid IO MEM Second half
+ */
+ .long TLB1_MAS0(1, 4, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000),
+ 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 5: 64M Non-cacheable, guarded
+ * 0xe000_0000 1M CCSRBAR
+ * 0xe200_0000 16M PCI1 IO
+ */
+ .long TLB1_MAS0(1, 5, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 6: 64M Cacheable, non-guarded
+ * 0xf000_0000 64M LBC SDRAM
+ */
+ .long TLB1_MAS0(1, 6, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+#if !defined(CONFIG_SPD_EEPROM)
+ /*
+ * TLB 7: 256M DDR
+ * 0x00000000 256M DDR System memory
+ * Without SPD EEPROM configured DDR, this must be setup manually.
+ * Make sure the TLB count at the top of this table is correct.
+ * Likely it needs to be increased by two for these entries.
+ */
+
+ .long TLB1_MAS0(1, 7, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+#endif
+
+ entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000 0x7fff_ffff DDR 2G
+ * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
+ * 0xc000_0000 0xdfff_ffff RapidIO 512M
+ * 0xe000_0000 0xe000_ffff CCSR 1M
+ * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
+ * 0xf000_0000 0xf7ff_ffff SDRAM 128M
+ * 0xf800_0000 0xf80f_ffff BCSR 1M
+ * 0xfc00_0000 0xffff_ffff FLASH (boot bank) 64M
+ *
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+#if !defined(CONFIG_SPD_EEPROM)
+#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M))
+#else
+#define LAWBAR0 0
+#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+#endif
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+/*
+ * This is not so much the SDRAM map as it is the whole localbus map.
+ */
+#define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
+#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+/*
+ * Rapid IO at 0xc000_0000 for 512 M
+ */
+#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+
+ .section .bootpg, "ax"
+ .globl law_entry
+law_entry:
+ entry_start
+ .long 0x05
+ .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+ .long LAWBAR4,LAWAR4
+ entry_end
diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c
new file mode 100644
index 0000000..5044708
--- /dev/null
+++ b/board/pm856/pm856.c
@@ -0,0 +1,449 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2003,Motorola Inc.
+ * Xianghua Xiao, (X.Xiao@motorola.com)
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <ioports.h>
+#include <spd.h>
+#include <miiphy.h>
+
+#if defined(CONFIG_DDR_ECC)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+long int fixed_sdram(void);
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+ /* Port A configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
+ /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
+ /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
+ /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
+ /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
+ /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
+ /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
+ /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
+ /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
+ /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
+ /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
+ /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
+ /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
+ /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
+ /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
+ /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
+ /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
+ /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
+ /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
+ /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
+ /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
+ /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
+ /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
+ /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
+ /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
+ /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
+ /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
+ /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
+ /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
+ /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
+ /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* FREERUN */
+ /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
+ },
+
+ /* Port B configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PB31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
+ /* PB30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
+ /* PB29 */ { 0, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
+ /* PB28 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
+ /* PB27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
+ /* PB26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
+ /* PB25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
+ /* PB24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
+ /* PB23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
+ /* PB22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
+ /* PB21 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
+ /* PB20 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
+ /* PB19 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
+ /* PB18 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
+ /* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
+ /* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
+ /* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
+ /* PB14 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
+ /* PB13 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:COL */
+ /* PB12 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
+ /* PB11 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB10 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB9 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB8 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
+ /* PB7 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB6 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB5 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB4 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
+ /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
+ },
+
+ /* Port C */
+ { /* conf ppar psor pdir podr pdat */
+ /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
+ /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
+ /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
+ /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
+ /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
+ /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
+ /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
+ /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
+ /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
+ /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
+ /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
+ /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
+ /* PC19 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
+ /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
+ /* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* PC17 */
+ /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
+ /* PC15 */ { 0, 1, 0, 0, 0, 0 }, /* PC15 */
+ /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
+ /* PC13 */ { 0, 1, 0, 0, 0, 0 }, /* PC13 */
+ /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
+ /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
+ /* PC10 */ { 0, 0, 0, 1, 0, 0 }, /* FETHMDC */
+ /* PC9 */ { 0, 0, 0, 0, 0, 0 }, /* FETHMDIO */
+ /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
+ /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
+ /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
+ /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
+ /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
+ /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
+ /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
+ /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
+ /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
+ },
+
+ /* Port D */
+ { /* conf ppar psor pdir podr pdat */
+ /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
+ /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
+ /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
+ /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* PD28 */
+ /* PD27 */ { 1, 1, 0, 1, 0, 0 }, /* PD27 */
+ /* PD26 */ { 1, 1, 0, 1, 0, 0 }, /* PD26 */
+ /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
+ /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
+ /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
+ /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
+ /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
+ /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
+ /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
+ /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
+ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
+ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
+ /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
+ /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */
+ /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
+ /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
+ /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
+ /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
+ /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
+ /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
+ /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
+ /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
+ /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
+ /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
+ /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
+ /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
+ }
+};
+
+
+int board_early_init_f (void)
+{
+ return 0;
+}
+
+void reset_phy (void)
+{
+}
+
+
+int checkboard (void)
+{
+ puts("Board: MicroSys PM856\n");
+
+#ifdef CONFIG_PCI
+ printf(" PCI1: 32 bit, %d MHz (compiled)\n",
+ CONFIG_SYS_CLK_FREQ / 1000000);
+#else
+ printf(" PCI1: disabled\n");
+#endif
+
+ /*
+ * Initialize local bus.
+ */
+ local_bus_init();
+
+ return 0;
+}
+
+
+long int
+initdram(int board_type)
+{
+ long dram_size = 0;
+ extern long spd_sdram (void);
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+ puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+ {
+ volatile ccsr_gur_t *gur= &immap->im_gur;
+ int i,x;
+
+ x = 10;
+
+ /*
+ * Work around to stabilize DDR DLL
+ */
+ gur->ddrdllcr = 0x81000000;
+ asm("sync;isync;msync");
+ udelay (200);
+ while (gur->ddrdllcr != 0x81000100)
+ {
+ gur->devdisr = gur->devdisr | 0x00010000;
+ asm("sync;isync;msync");
+ for (i=0; i<x; i++)
+ ;
+ gur->devdisr = gur->devdisr & 0xfff7ffff;
+ asm("sync;isync;msync");
+ x++;
+ }
+ }
+#endif
+
+#if defined(CONFIG_SPD_EEPROM)
+ dram_size = spd_sdram ();
+#else
+ dram_size = fixed_sdram ();
+#endif
+
+#if defined(CONFIG_DDR_ECC)
+ /*
+ * Initialize and enable DDR ECC.
+ */
+ ddr_enable_ecc(dram_size);
+#endif
+
+ puts(" DDR: ");
+ return dram_size;
+}
+
+
+/*
+ * Initialize Local Bus
+ */
+
+void
+local_bus_init(void)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+ uint clkdiv;
+ uint lbc_hz;
+ sys_info_t sysinfo;
+
+ /*
+ * Errata LBC11.
+ * Fix Local Bus clock glitch when DLL is enabled.
+ *
+ * If localbus freq is < 66Mhz, DLL bypass mode must be used.
+ * If localbus freq is > 133Mhz, DLL can be safely enabled.
+ * Between 66 and 133, the DLL is enabled with an override workaround.
+ */
+
+ get_sys_info(&sysinfo);
+ clkdiv = lbc->lcrr & 0x0f;
+ lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+ if (lbc_hz < 66) {
+ lbc->lcrr = CFG_LBC_LCRR | 0x80000000; /* DLL Bypass */
+
+ } else if (lbc_hz >= 133) {
+ lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */
+
+ } else {
+ /*
+ * On REV1 boards, need to change CLKDIV before enable DLL.
+ * Default CLKDIV is 8, change it to 4 temporarily.
+ */
+ uint pvr = get_pvr();
+ uint temp_lbcdll = 0;
+
+ if (pvr == PVR_85xx_REV1) {
+ /* FIXME: Justify the high bit here. */
+ lbc->lcrr = 0x10000004;
+ }
+
+ lbc->lcrr = CFG_LBC_LCRR & (~0x80000000);/* DLL Enabled */
+ udelay(200);
+
+ /*
+ * Sample LBC DLL ctrl reg, upshift it to set the
+ * override bits.
+ */
+ temp_lbcdll = gur->lbcdllcr;
+ gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+ asm("sync;isync;msync");
+ }
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+ uint *pstart = (uint *) CFG_MEMTEST_START;
+ uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *p;
+
+ printf("SDRAM test phase 1:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("SDRAM test phase 2:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("SDRAM test passed.\n");
+ return 0;
+}
+#endif
+
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*************************************************************************
+ * fixed sdram init -- doesn't use serial presence detect.
+ ************************************************************************/
+long int fixed_sdram (void)
+{
+ #ifndef CFG_RAMBOOT
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+
+ ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
+ ddr->cs0_config = CFG_DDR_CS0_CONFIG;
+ ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
+ ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
+ ddr->sdram_mode = CFG_DDR_MODE;
+ ddr->sdram_interval = CFG_DDR_INTERVAL;
+ #if defined (CONFIG_DDR_ECC)
+ ddr->err_disable = 0x0000000D;
+ ddr->err_sbe = 0x00ff0000;
+ #endif
+ asm("sync;isync;msync");
+ udelay(500);
+ #if defined (CONFIG_DDR_ECC)
+ /* Enable ECC checking */
+ ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000);
+ #else
+ ddr->sdram_cfg = CFG_DDR_CONTROL;
+ #endif
+ asm("sync; isync; msync");
+ udelay(500);
+ #endif
+ return CFG_SDRAM_SIZE * 1024 * 1024;
+}
+#endif /* !defined(CONFIG_SPD_EEPROM) */
+
+
+#if defined(CONFIG_PCI)
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc85xxads_config_table[] = {
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+ PCI_IDSEL_NUMBER, PCI_ANY_ID,
+ pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+ } },
+ { }
+};
+#endif
+
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+ config_table: pci_mpc85xxads_config_table,
+#endif
+};
+
+#endif /* CONFIG_PCI */
+
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+ extern void pci_mpc85xx_init(struct pci_controller *hose);
+
+ pci_mpc85xx_init(&hose);
+#endif /* CONFIG_PCI */
+}
diff --git a/board/pm856/u-boot.lds b/board/pm856/u-boot.lds
new file mode 100644
index 0000000..7553506
--- /dev/null
+++ b/board/pm856/u-boot.lds
@@ -0,0 +1,152 @@
+/*
+ * (C) Copyright 2002,2003,Motorola,Inc.
+ * Xianghua Xiao, X.Xiao@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ .resetvec 0xFFFFFFFC :
+ {
+ *(.resetvec)
+ } = 0xffff
+
+ .bootpg 0xFFFFF000 :
+ {
+ cpu/mpc85xx/start.o (.bootpg)
+ board/pm856/init.o (.bootpg)
+ } = 0xffff
+
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc85xx/start.o (.text)
+ board/pm856/init.o (.text)
+ cpu/mpc85xx/commproc.o (.text)
+ cpu/mpc85xx/traps.o (.text)
+ cpu/mpc85xx/interrupts.o (.text)
+ cpu/mpc85xx/serial_scc.o (.text)
+ cpu/mpc85xx/ether_fcc.o (.text)
+ cpu/mpc85xx/cpu_init.o (.text)
+ cpu/mpc85xx/cpu.o (.text)
+ cpu/mpc85xx/tsec.o (.text)
+ cpu/mpc85xx/speed.o (.text)
+ cpu/mpc85xx/i2c.o (.text)
+ cpu/mpc85xx/spd_sdram.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_ppc/extable.o (.text)
+ lib_generic/zlib.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/drivers/ct69000.c b/drivers/ct69000.c
index bc2853e..7bcf19f 100644
--- a/drivers/ct69000.c
+++ b/drivers/ct69000.c
@@ -23,8 +23,6 @@
* MA 02111-1307 USA
*/
-
-
#include <common.h>
#ifdef CONFIG_VIDEO
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index 12a7181..07e3f06 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -104,7 +104,7 @@
/*
* Determine DDR configuration from I2C interface.
*/
- #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS 0x58 /* DDR DIMM */
#else
/*
@@ -146,6 +146,12 @@
#undef CFG_RAMBOOT
#endif
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
/*
* Local Bus Definitions
*/
@@ -255,14 +261,14 @@
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 3
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_MPC85XX_FEC 1
#define CONFIG_MPC85XX_FEC_NAME "FEC"
-#define FEC_PHY_ADDR 1
+#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
/* Options are: TSEC[0-1] */
@@ -388,13 +394,13 @@
#define CONFIG_ETH2ADDR 00:40:42:01:00:02
#endif
+
+#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx
+#define CONFIG_BOOTFILE pm854/uImage
+
+#define CONFIG_HOSTNAME pm854
#define CONFIG_IPADDR 192.168.0.103
-
-#define CONFIG_HOSTNAME PM854
-#define CONFIG_ROOTPATH /opt/eldk30/ppc_82xx
-#define CONFIG_BOOTFILE uImage
-
-#define CONFIG_SERVERIP 192.168.0.54
+#define CONFIG_SERVERIP 192.168.0.64
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_NETMASK 255.255.255.0
@@ -409,7 +415,7 @@
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=400000\0" \
- "ramdiskfile=uRamdisk\0"
+ "ramdiskfile=pm854/uRamdisk\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
new file mode 100644
index 0000000..5dae1b6
--- /dev/null
+++ b/include/configs/PM856.h
@@ -0,0 +1,439 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * MicroSys PM856 board configuration file
+ *
+ * Please refer to doc/README.mpc85xx for more info.
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
+#define CONFIG_MPC8560 1 /* MPC8560 specific */
+#define CONFIG_PM856 1 /* PM856 board specific */
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
+
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ * 33000000
+ * 66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz. In any event, this value
+ * must match the settings of some switches. Details can be found
+ * in the README.mpc85xxads.
+ */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 66000000
+#endif
+
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_END 0x00400000
+
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS 0x58 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR parameters
+ */
+ #define CFG_SDRAM_SIZE 256 /* DDR is 256 MB */
+ #define CFG_DDR_CS0_BNDS 0x0000000f /* 0-256MB */
+ #define CFG_DDR_CS0_CONFIG 0x80000102
+ #define CFG_DDR_TIMING_1 0x47444321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+ #define CFG_DDR_CONTROL 0xc2008000 /* unbuffered,no DYN_PWR */
+ #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+ #define CFG_DDR_INTERVAL 0x045b0100 /* autocharge,no open page */
+#endif
+
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 0 /* LBC SDRAM is 0 MB */
+
+#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH 32M */
+#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */
+
+#define CFG_OR0_PRELIM 0xfe006f67 /* 32MB Flash */
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
+/*
+ * Local Bus Definitions
+ */
+
+#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
+
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+/*
+ * EEPROM configuration
+ */
+#define CFG_I2C_EEPROM_ADDR 0x58
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR 0x51
+
+/* RapidIO MMU */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC2 1
+#undef CONFIG_MPC85XX_FEC
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+
+#endif /* CONFIG_TSEC_ENET */
+
+#define CONFIG_ETHPRIME "ENET0"
+
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+
+
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK14
+ * - Select bus for bd/buffers
+ * - Full duplex
+ */
+#define CONFIG_ETHER_ON_FCC3
+#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14)
+#define CFG_CPMFCR_RAMTYPE 0
+#define CFG_FCC_PSMR (FCC_PSMR_FDE)
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x80000)
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#if defined(CFG_RAMBOOT)
+ #if defined(CONFIG_PCI)
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_PCI \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
+ #else
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
+ #endif
+#else
+ #if defined(CONFIG_PCI)
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_EEPROM \
+ | CFG_CMD_DATE \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
+ #else
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_EEPROM \
+ | CFG_CMD_DATE \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
+ #endif
+#endif
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x1000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_LOOPW
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_ETHADDR 00:40:42:01:00:00
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:40:42:01:00:01
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR 00:40:42:01:00:02
+#endif
+
+
+#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx
+#define CONFIG_BOOTFILE pm856/uImage
+
+#define CONFIG_HOSTNAME pm856
+#define CONFIG_IPADDR 192.168.0.103
+#define CONFIG_SERVERIP 192.168.0.64
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 9600
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=400000\0" \
+ "ramdiskfile=pm856/uRamdisk\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+
+#endif /* __CONFIG_H */