arm/km: fix u-boot.kwb build breakage
commit 010a958b
(arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h)
breaks building keymile arm targets, when u-boot.kwb tries to
generate the binary with mkimage. A simple make <board> or MAKEALL
succeeded because it don't try to build the kirwood binary at the end.
Due this commit we use the CONFIG_SYS_KWD_CONFIG from the
arch-kirkwood/config.h and it was removed from the board config.
But it was forgotten to include the header. Now the header is included
in km_arm.h. Some other defines were obsolete due to this include,
these are also removed in this commit.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 20ee6ea..4741278 100644
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -40,7 +40,6 @@
* High Level Configuration Options (easy to change)
*/
#define CONFIG_MARVELL
-#define CONFIG_ARM926EJS /* Basic Architecture */
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
#define CONFIG_KIRKWOOD /* SOC Family Name */
#define CONFIG_KW88F6281 /* SOC Name */
@@ -49,6 +48,12 @@
/* include common defines/options for all Keymile boards */
#include "keymile-common.h"
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_SF
+#define CONFIG_SOFT_I2C /* I2C bit-banged */
+
+#include "asm/arch/config.h"
+
#define CONFIG_SYS_TEXT_BASE 0x04000000 /* code address after reloc */
#define CONFIG_ENV_SIZE (128 << 10) /* NAND chip block size */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
@@ -75,12 +80,7 @@
#define CONFIG_KM_ARCH_DBG_FILE "scripts/debug-arm-env.txt"
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#undef CONFIG_KIRKWOOD_PCIE_INIT /* Disable PCIE Port0 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-
#define CONFIG_MISC_INIT_R
/*
@@ -116,7 +116,6 @@
*/
#define CONFIG_CMD_ELF
#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_NAND
#define CONFIG_CMD_NFS
/*
@@ -131,8 +130,6 @@
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_NAND_BASE 0xd8000000
#define BOOTFLASH_START 0x0
@@ -175,8 +172,6 @@
/*
* I2C related stuff
*/
-#define CONFIG_SOFT_I2C /* I2C bit-banged */
-
#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
#if defined(CONFIG_SOFT_I2C)
#ifndef __ASSEMBLY__
@@ -200,8 +195,6 @@
#define I2C_DELAY udelay(3) /* 1/4 I2C clock duration */
#define I2C_SOFT_DECLARATIONS
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_SYS_I2C_SPEED 100000
#endif
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
@@ -224,15 +217,8 @@
#define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#define CONFIG_CMD_SF
-
#define CONFIG_SPI_FLASH
-#define CONFIG_HARD_SPI
-#define CONFIG_KIRKWOOD_SPI
#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50Mhz */
#define FLASH_GPIO_PIN 0x00010000
@@ -272,8 +258,6 @@
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000
/* Do early setups now in board_init_f() */
#define CONFIG_BOARD_EARLY_INIT_F
diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h
index 6d56d7d..8d1b61f 100644
--- a/include/configs/mgcoge3un.h
+++ b/include/configs/mgcoge3un.h
@@ -48,6 +48,7 @@
#define KM_ENV_BUS "pca9547:70:d" /* I2C2 (Mux-Port 5)*/
/* we use a new RAM type on mgcoge3un board */
+#undef CONFIG_SYS_KWD_CONFIG
#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg
/*