sunxi: H3/H5 Sync DT files from upstream Linux kernel as of next-20200108
Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo
98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next
which is also part of next-20200108.
Changes brought in include:
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index f1fc6bd..597c425 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -75,8 +75,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
status_led {
label = "orangepi:red:status";
@@ -92,8 +90,6 @@
r_gpio_keys {
compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&sw_r_opc>;
sw2 {
label = "sw2";
@@ -110,8 +106,6 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
};
};
@@ -152,7 +146,7 @@
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&r_ir_rx_pin>;
status = "okay";
};
@@ -179,30 +173,6 @@
};
};
-&pio {
- leds_opc: led_pins {
- pins = "PA15";
- function = "gpio_out";
- };
-};
-
-&r_pio {
- leds_r_opc: led_pins {
- pins = "PL10";
- function = "gpio_out";
- };
-
- sw_r_opc: key_pins {
- pins = "PL3", "PL4";
- function = "gpio_in";
- };
-
- wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
- pins = "PL7";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
status = "okay";
@@ -210,7 +180,7 @@
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};