PPC405EP support added.
diff --git a/include/ppc405.h b/include/ppc405.h
index c99d591..243a22d 100644
--- a/include/ppc405.h
+++ b/include/ppc405.h
@@ -151,11 +151,13 @@
#define memcfga (SDRAM_DCR_BASE+0x0) /* Memory configuration address reg */
#define memcfgd (SDRAM_DCR_BASE+0x1) /* Memory configuration data reg */
/* values for memcfga register - indirect addressing of these regs */
+#ifndef CONFIG_405EP
#define mem_besra 0x00 /* bus error syndrome reg a */
#define mem_besrsa 0x04 /* bus error syndrome reg set a */
#define mem_besrb 0x08 /* bus error syndrome reg b */
#define mem_besrsb 0x0c /* bus error syndrome reg set b */
#define mem_bear 0x10 /* bus error address reg */
+#endif
#define mem_mcopt1 0x20 /* memory controller options 1 */
#define mem_rtr 0x30 /* refresh timer reg */
#define mem_pmit 0x34 /* power management idle timer */
@@ -164,8 +166,10 @@
#define mem_mb2cf 0x48 /* memory bank 2 configuration */
#define mem_mb3cf 0x4c /* memory bank 3 configuration */
#define mem_sdtr1 0x80 /* timing reg 1 */
+#ifndef CONFIG_405EP
#define mem_ecccf 0x94 /* ECC configuration */
#define mem_eccerr 0x98 /* ECC error status */
+#endif
/******************************************************************************
* Decompression Controller
@@ -227,6 +231,255 @@
#define pbesr1 0x22 /* periph bus error status reg 1 */
#define epcr 0x23 /* external periph control reg */
+#ifdef CONFIG_405EP
+/******************************************************************************
+ * Control
+ ******************************************************************************/
+#define CNTRL_DCR_BASE 0x0f0
+#define cpc0_pllmr0 (CNTRL_DCR_BASE+0x0) /* PLL mode register 0 */
+#define cpc0_boot (CNTRL_DCR_BASE+0x1) /* Clock status register */
+#define cpc0_epctl (CNTRL_DCR_BASE+0x3) /* EMAC to PHY control register */
+#define cpc0_pllmr1 (CNTRL_DCR_BASE+0x4) /* PLL mode register 1 */
+#define cpc0_ucr (CNTRL_DCR_BASE+0x5) /* UART control register */
+#define cpc0_pci (CNTRL_DCR_BASE+0x9) /* PCI control register */
+
+#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */
+#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */
+#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */
+#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register*/
+#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */
+#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */
+#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */
+#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */
+#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */
+#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */
+
+/* Bit definitions */
+#define PLLMR0_CPU_DIV_MASK 0x00300000 /* CPU clock divider */
+#define PLLMR0_CPU_DIV_BYPASS 0x00000000
+#define PLLMR0_CPU_DIV_2 0x00100000
+#define PLLMR0_CPU_DIV_3 0x00200000
+#define PLLMR0_CPU_DIV_4 0x00300000
+
+#define PLLMR0_CPU_TO_PLB_MASK 0x00030000 /* CPU:PLB Frequency Divisor */
+#define PLLMR0_CPU_PLB_DIV_1 0x00000000
+#define PLLMR0_CPU_PLB_DIV_2 0x00010000
+#define PLLMR0_CPU_PLB_DIV_3 0x00020000
+#define PLLMR0_CPU_PLB_DIV_4 0x00030000
+
+#define PLLMR0_OPB_TO_PLB_MASK 0x00003000 /* OPB:PLB Frequency Divisor */
+#define PLLMR0_OPB_PLB_DIV_1 0x00000000
+#define PLLMR0_OPB_PLB_DIV_2 0x00001000
+#define PLLMR0_OPB_PLB_DIV_3 0x00002000
+#define PLLMR0_OPB_PLB_DIV_4 0x00003000
+
+#define PLLMR0_EXB_TO_PLB_MASK 0x00000300 /* External Bus:PLB Divisor */
+#define PLLMR0_EXB_PLB_DIV_2 0x00000000
+#define PLLMR0_EXB_PLB_DIV_3 0x00000100
+#define PLLMR0_EXB_PLB_DIV_4 0x00000200
+#define PLLMR0_EXB_PLB_DIV_5 0x00000300
+
+#define PLLMR0_MAL_TO_PLB_MASK 0x00000030 /* MAL:PLB Divisor */
+#define PLLMR0_MAL_PLB_DIV_1 0x00000000
+#define PLLMR0_MAL_PLB_DIV_2 0x00000010
+#define PLLMR0_MAL_PLB_DIV_3 0x00000020
+#define PLLMR0_MAL_PLB_DIV_4 0x00000030
+
+#define PLLMR0_PCI_TO_PLB_MASK 0x00000003 /* PCI:PLB Frequency Divisor */
+#define PLLMR0_PCI_PLB_DIV_1 0x00000000
+#define PLLMR0_PCI_PLB_DIV_2 0x00000001
+#define PLLMR0_PCI_PLB_DIV_3 0x00000002
+#define PLLMR0_PCI_PLB_DIV_4 0x00000003
+
+#define PLLMR1_SSCS_MASK 0x80000000 /* Select system clock source */
+#define PLLMR1_PLLR_MASK 0x40000000 /* PLL reset */
+#define PLLMR1_FBMUL_MASK 0x00F00000 /* PLL feedback multiplier value */
+#define PLLMR1_FBMUL_DIV_16 0x00000000
+#define PLLMR1_FBMUL_DIV_1 0x00100000
+#define PLLMR1_FBMUL_DIV_2 0x00200000
+#define PLLMR1_FBMUL_DIV_3 0x00300000
+#define PLLMR1_FBMUL_DIV_4 0x00400000
+#define PLLMR1_FBMUL_DIV_5 0x00500000
+#define PLLMR1_FBMUL_DIV_6 0x00600000
+#define PLLMR1_FBMUL_DIV_7 0x00700000
+#define PLLMR1_FBMUL_DIV_8 0x00800000
+#define PLLMR1_FBMUL_DIV_9 0x00900000
+#define PLLMR1_FBMUL_DIV_10 0x00A00000
+#define PLLMR1_FBMUL_DIV_11 0x00B00000
+#define PLLMR1_FBMUL_DIV_12 0x00C00000
+#define PLLMR1_FBMUL_DIV_13 0x00D00000
+#define PLLMR1_FBMUL_DIV_14 0x00E00000
+#define PLLMR1_FBMUL_DIV_15 0x00F00000
+
+#define PLLMR1_FWDVA_MASK 0x00070000 /* PLL forward divider A value */
+#define PLLMR1_FWDVA_DIV_8 0x00000000
+#define PLLMR1_FWDVA_DIV_7 0x00010000
+#define PLLMR1_FWDVA_DIV_6 0x00020000
+#define PLLMR1_FWDVA_DIV_5 0x00030000
+#define PLLMR1_FWDVA_DIV_4 0x00040000
+#define PLLMR1_FWDVA_DIV_3 0x00050000
+#define PLLMR1_FWDVA_DIV_2 0x00060000
+#define PLLMR1_FWDVA_DIV_1 0x00070000
+#define PLLMR1_FWDVB_MASK 0x00007000 /* PLL forward divider B value */
+#define PLLMR1_TUNING_MASK 0x000003FF /* PLL tune bits */
+
+/* Defines for CPC0_EPRCSR register */
+#define CPC0_EPRCSR_E0NFE 0x80000000
+#define CPC0_EPRCSR_E1NFE 0x40000000
+#define CPC0_EPRCSR_E1RPP 0x00000080
+#define CPC0_EPRCSR_E0RPP 0x00000040
+#define CPC0_EPRCSR_E1ERP 0x00000020
+#define CPC0_EPRCSR_E0ERP 0x00000010
+#define CPC0_EPRCSR_E1PCI 0x00000002
+#define CPC0_EPRCSR_E0PCI 0x00000001
+
+/* Defines for CPC0_PCI Register */
+#define CPC0_PCI_SPE 0x00000010 /* PCIINT/WE select */
+#define CPC0_PCI_HOST_CFG_EN 0x00000008 /* PCI host config Enable */
+#define CPC0_PCI_ARBIT_EN 0x00000001 /* PCI Internal Arb Enabled*/
+
+/* Defines for CPC0_BOOR Register */
+#define CPC0_BOOT_SEP 0x00000002 /* serial EEPROM present */
+
+/* Defines for CPC0_PLLMR1 Register fields */
+#define PLL_ACTIVE 0x80000000
+#define CPC0_PLLMR1_SSCS 0x80000000
+#define PLL_RESET 0x40000000
+#define CPC0_PLLMR1_PLLR 0x40000000
+ /* Feedback multiplier */
+#define PLL_FBKDIV 0x00F00000
+#define CPC0_PLLMR1_FBDV 0x00F00000
+#define PLL_FBKDIV_16 0x00000000
+#define PLL_FBKDIV_1 0x00100000
+#define PLL_FBKDIV_2 0x00200000
+#define PLL_FBKDIV_3 0x00300000
+#define PLL_FBKDIV_4 0x00400000
+#define PLL_FBKDIV_5 0x00500000
+#define PLL_FBKDIV_6 0x00600000
+#define PLL_FBKDIV_7 0x00700000
+#define PLL_FBKDIV_8 0x00800000
+#define PLL_FBKDIV_9 0x00900000
+#define PLL_FBKDIV_10 0x00A00000
+#define PLL_FBKDIV_11 0x00B00000
+#define PLL_FBKDIV_12 0x00C00000
+#define PLL_FBKDIV_13 0x00D00000
+#define PLL_FBKDIV_14 0x00E00000
+#define PLL_FBKDIV_15 0x00F00000
+ /* Forward A divisor */
+#define PLL_FWDDIVA 0x00070000
+#define CPC0_PLLMR1_FWDVA 0x00070000
+#define PLL_FWDDIVA_8 0x00000000
+#define PLL_FWDDIVA_7 0x00010000
+#define PLL_FWDDIVA_6 0x00020000
+#define PLL_FWDDIVA_5 0x00030000
+#define PLL_FWDDIVA_4 0x00040000
+#define PLL_FWDDIVA_3 0x00050000
+#define PLL_FWDDIVA_2 0x00060000
+#define PLL_FWDDIVA_1 0x00070000
+ /* Forward B divisor */
+#define PLL_FWDDIVB 0x00007000
+#define CPC0_PLLMR1_FWDVB 0x00007000
+#define PLL_FWDDIVB_8 0x00000000
+#define PLL_FWDDIVB_7 0x00001000
+#define PLL_FWDDIVB_6 0x00002000
+#define PLL_FWDDIVB_5 0x00003000
+#define PLL_FWDDIVB_4 0x00004000
+#define PLL_FWDDIVB_3 0x00005000
+#define PLL_FWDDIVB_2 0x00006000
+#define PLL_FWDDIVB_1 0x00007000
+ /* PLL tune bits */
+#define PLL_TUNE_MASK 0x000003FF
+#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
+#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
+#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
+#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
+#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
+#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
+#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
+
+/* Defines for CPC0_PLLMR0 Register fields */
+ /* CPU divisor */
+#define PLL_CPUDIV 0x00300000
+#define CPC0_PLLMR0_CCDV 0x00300000
+#define PLL_CPUDIV_1 0x00000000
+#define PLL_CPUDIV_2 0x00100000
+#define PLL_CPUDIV_3 0x00200000
+#define PLL_CPUDIV_4 0x00300000
+ /* PLB divisor */
+#define PLL_PLBDIV 0x00030000
+#define CPC0_PLLMR0_CBDV 0x00030000
+#define PLL_PLBDIV_1 0x00000000
+#define PLL_PLBDIV_2 0x00010000
+#define PLL_PLBDIV_3 0x00020000
+#define PLL_PLBDIV_4 0x00030000
+ /* OPB divisor */
+#define PLL_OPBDIV 0x00003000
+#define CPC0_PLLMR0_OPDV 0x00003000
+#define PLL_OPBDIV_1 0x00000000
+#define PLL_OPBDIV_2 0x00001000
+#define PLL_OPBDIV_3 0x00002000
+#define PLL_OPBDIV_4 0x00003000
+ /* EBC divisor */
+#define PLL_EXTBUSDIV 0x00000300
+#define CPC0_PLLMR0_EPDV 0x00000300
+#define PLL_EXTBUSDIV_2 0x00000000
+#define PLL_EXTBUSDIV_3 0x00000100
+#define PLL_EXTBUSDIV_4 0x00000200
+#define PLL_EXTBUSDIV_5 0x00000300
+ /* MAL divisor */
+#define PLL_MALDIV 0x00000030
+#define CPC0_PLLMR0_MPDV 0x00000030
+#define PLL_MALDIV_1 0x00000000
+#define PLL_MALDIV_2 0x00000010
+#define PLL_MALDIV_3 0x00000020
+#define PLL_MALDIV_4 0x00000030
+ /* PCI divisor */
+#define PLL_PCIDIV 0x00000003
+#define CPC0_PLLMR0_PPFD 0x00000003
+#define PLL_PCIDIV_1 0x00000000
+#define PLL_PCIDIV_2 0x00000001
+#define PLL_PCIDIV_3 0x00000002
+#define PLL_PCIDIV_4 0x00000003
+
+/*
+ *-------------------------------------------------------------------------------
+ * PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
+ * assuming a 33.3MHz input clock to the 405EP.
+ *-------------------------------------------------------------------------------
+ */
+#define PLLMR0_266_133_66 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \
+ PLL_MALDIV_1 | PLL_PCIDIV_4)
+#define PLLMR1_266_133_66 (PLL_FBKDIV_8 | \
+ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
+ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
+
+#define PLLMR0_133_66_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
+ PLL_MALDIV_1 | PLL_PCIDIV_4)
+#define PLLMR1_133_66_66_33 (PLL_FBKDIV_4 | \
+ PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
+ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
+#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
+ PLL_MALDIV_1 | PLL_PCIDIV_4)
+#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
+ PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
+ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
+#define PLLMR0_266_133_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
+ PLL_MALDIV_1 | PLL_PCIDIV_4)
+#define PLLMR1_266_133_66_33 (PLL_FBKDIV_8 | \
+ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
+ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
+
+/*
+ * PLL Voltage Controlled Oscillator (VCO) definitions
+ * Maximum and minimum values (in MHz) for correct PLL operation.
+ */
+#define VCO_MIN 500
+#define VCO_MAX 1000
+#else /* #ifdef CONFIG_405EP */
/******************************************************************************
* Control
******************************************************************************/
@@ -236,7 +489,8 @@
#define cntrl1 (CNTRL_DCR_BASE+0x2) /* Control 1 register */
#define reset (CNTRL_DCR_BASE+0x3) /* reset register */
#define strap (CNTRL_DCR_BASE+0x4) /* strap register */
-#define ecr (0xAA) /* edge conditioning register (405GPr) */
+
+#define ecr (0xaa) /* edge conditioner register (405gpr) */
/* Bit definitions */
#define PLLMR_FWD_DIV_MASK 0xE0000000 /* Forward Divisor */
@@ -300,6 +554,7 @@
*/
#define VCO_MIN 400
#define VCO_MAX 800
+#endif /* #ifdef CONFIG_405EP */
/******************************************************************************
* Memory Access Layer
@@ -364,6 +619,25 @@
#define ocmdsarc (OCM_DCR_BASE+0x02) /* OCM D-side address compare reg */
#define ocmdscntl (OCM_DCR_BASE+0x03) /* OCM D-side control reg */
+/******************************************************************************
+ * GPIO macro register defines
+ ******************************************************************************/
+#define GPIO_BASE 0xEF600700
+#define GPIO0_OR (GPIO_BASE+0x0)
+#define GPIO0_TCR (GPIO_BASE+0x4)
+#define GPIO0_OSRH (GPIO_BASE+0x8)
+#define GPIO0_OSRL (GPIO_BASE+0xC)
+#define GPIO0_TSRH (GPIO_BASE+0x10)
+#define GPIO0_TSRL (GPIO_BASE+0x14)
+#define GPIO0_ODR (GPIO_BASE+0x18)
+#define GPIO0_IR (GPIO_BASE+0x1C)
+#define GPIO0_RR1 (GPIO_BASE+0x20)
+#define GPIO0_RR2 (GPIO_BASE+0x24)
+#define GPIO0_ISR1H (GPIO_BASE+0x30)
+#define GPIO0_ISR1L (GPIO_BASE+0x34)
+#define GPIO0_ISR2H (GPIO_BASE+0x38)
+#define GPIO0_ISR2L (GPIO_BASE+0x3C)
+
/*
* Macro for accessing the indirect EBC register