mx6: Add initial SPL support for HummingBoard-i2eX
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/board/solidrun/mx6cuboxi/mx6cuboxi.c b/board/solidrun/mx6cuboxi/mx6cuboxi.c
new file mode 100644
index 0000000..b696dcb
--- /dev/null
+++ b/board/solidrun/mx6cuboxi/mx6cuboxi.c
@@ -0,0 +1,330 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
+ *
+ * Based on SPL code from Solidrun tree, which is:
+ * Author: Tungyi Lin <tungyilin1127@gmail.com>
+ *
+ * Derived from EDM_CF_IMX6 code by TechNexion,Inc
+ * Ported to SolidRun microSOM by Rabeeh Khoury <rabeeh@solid-run.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mx6-ddr.h>
+#include <spl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ETH_PHY_RESET IMX_GPIO_NR(4, 15)
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC2_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1; /* uSDHC2 is always present */
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+static iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* AR8035 reset */
+ MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+ /* AR8035 interrupt */
+ MX6_PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* GPIO16 -> AR8035 25MHz */
+ MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
+ MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+ MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+ MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
+};
+
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+ gpio_direction_output(ETH_PHY_RESET, 0);
+ mdelay(2);
+ gpio_set_value(ETH_PHY_RESET, 1);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ int ret = enable_fec_anatop_clock(ENET_25MHZ);
+ if (ret)
+ return ret;
+
+ /* set gpr1[ENET_CLK_SEL] */
+ setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+
+ setup_iomux_enet();
+
+ return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: MX6 Hummingboard\n");
+ return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_ddr_type = 0x000C0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_ddrpke = 0x00000000,
+ .grp_addds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+static const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpwldectrl1 = 0x00000000,
+ .p1_mpwldectrl0 = 0x00000000,
+ .p1_mpwldectrl1 = 0x00000000,
+ .p0_mpdgctrl0 = 0x0314031c,
+ .p0_mpdgctrl1 = 0x023e0304,
+ .p1_mpdgctrl0 = 0x03240330,
+ .p1_mpdgctrl1 = 0x03180260,
+ .p0_mprddlctl = 0x3630323c,
+ .p1_mprddlctl = 0x3436283a,
+ .p0_mpwrdlctl = 0x36344038,
+ .p1_mpwrdlctl = 0x422a423c,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+ .mem_speed = 1600,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+ .SRT = 1,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0x00C03F3F, &ccm->CCGR0);
+ writel(0x0030FC03, &ccm->CCGR1);
+ writel(0x0FFFC000, &ccm->CCGR2);
+ writel(0x3FF00000, &ccm->CCGR3);
+ writel(0x00FFF300, &ccm->CCGR4);
+ writel(0x0F0000C3, &ccm->CCGR5);
+ writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* enable AXI cache for VDOA/VPU/IPU */
+ writel(0xF00000CF, &iomux->gpr[4]);
+ /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+ writel(0x007F007F, &iomux->gpr[6]);
+ writel(0x007F007F, &iomux->gpr[7]);
+}
+
+/*
+ * This section requires the differentiation between Solidrun mx6 boards, but
+ * for now, it will configure only for the mx6dual hummingboard version.
+ */
+static void spl_dram_init(void)
+{
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus: 0=16, 1=32, 2=64 */
+ .dsize = 2,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ .ncs = 1, /* single chip select */
+ .cs1_mirror = 0,
+ .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
+ .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ };
+
+ mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ ccgr_init();
+ gpr_init();
+
+ /* iomux and setup of i2c */
+ board_early_init_f();
+
+ /* setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
+#endif