dw_mmc: cleanups
dw_mmc driver was responding to errors with debug(). Change that to
prinf so that any errors are immediately obvious. Also adjust english
in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
index 0df30bc..4c16e7f 100644
--- a/drivers/mmc/dw_mmc.c
+++ b/drivers/mmc/dw_mmc.c
@@ -177,14 +177,16 @@
}
}
- if (i == retry)
+ if (i == retry) {
+ printf("dwmci_send_cmd: timeout..\n");
return TIMEOUT;
+ }
if (mask & DWMCI_INTMSK_RTO) {
- debug("Response Timeout..\n");
+ printf("dwmci_send_cmd: Response Timeout..\n");
return TIMEOUT;
} else if (mask & DWMCI_INTMSK_RE) {
- debug("Response Error..\n");
+ printf("dwmci_send_cmd: Response Error..\n");
return -1;
}
@@ -204,7 +206,7 @@
do {
mask = dwmci_readl(host, DWMCI_RINTSTS);
if (mask & (DWMCI_DATA_ERR | DWMCI_DATA_TOUT)) {
- debug("DATA ERROR!\n");
+ printf("dwmci_send_cmd: DATA ERROR!\n");
return -1;
}
} while (!(mask & DWMCI_INTMSK_DTO));
@@ -232,16 +234,16 @@
if ((freq == host->clock) || (freq == 0))
return 0;
/*
- * If host->get_mmc_clk didn't define,
+ * If host->get_mmc_clk isn't defined,
* then assume that host->bus_hz is source clock value.
- * host->bus_hz should be set from user.
+ * host->bus_hz should be set by user.
*/
if (host->get_mmc_clk)
sclk = host->get_mmc_clk(host);
else if (host->bus_hz)
sclk = host->bus_hz;
else {
- printf("Didn't get source clock value..\n");
+ printf("dwmci_setup_bus: Didn't get source clock value..\n");
return -EINVAL;
}
@@ -260,7 +262,7 @@
do {
status = dwmci_readl(host, DWMCI_CMD);
if (timeout-- < 0) {
- printf("TIMEOUT error!!\n");
+ printf("dwmci_setup_bus: timeout!\n");
return -ETIMEDOUT;
}
} while (status & DWMCI_CMD_START);
@@ -275,7 +277,7 @@
do {
status = dwmci_readl(host, DWMCI_CMD);
if (timeout-- < 0) {
- printf("TIMEOUT error!!\n");
+ printf("dwmci_setup_bus: timeout!\n");
return -ETIMEDOUT;
}
} while (status & DWMCI_CMD_START);
@@ -290,7 +292,7 @@
struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
u32 ctype, regs;
- debug("Buswidth = %d, clock: %d\n",mmc->bus_width, mmc->clock);
+ debug("Buswidth = %d, clock: %d\n", mmc->bus_width, mmc->clock);
dwmci_setup_bus(host, mmc->clock);
switch (mmc->bus_width) {
@@ -329,7 +331,7 @@
dwmci_writel(host, DWMCI_PWREN, 1);
if (!dwmci_wait_reset(host, DWMCI_RESET_ALL)) {
- debug("%s[%d] Fail-reset!!\n",__func__,__LINE__);
+ printf("%s[%d] Fail-reset!!\n", __func__, __LINE__);
return -1;
}