rockchip: rk3328: Add support for ROC-RK3328-CC board
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index af7d804..a683525 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -106,6 +106,7 @@
dtb-$(CONFIG_ROCKCHIP_RK3328) += \
rk3328-evb.dtb \
+ rk3328-roc-cc.dtb \
rk3328-rock64.dtb
dtb-$(CONFIG_ROCKCHIP_RK3368) += \
diff --git a/arch/arm/dts/rk3328-roc-cc-u-boot.dtsi b/arch/arm/dts/rk3328-roc-cc-u-boot.dtsi
new file mode 100644
index 0000000..e929d86
--- /dev/null
+++ b/arch/arm/dts/rk3328-roc-cc-u-boot.dtsi
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd
+ */
+
+#include "rk3328-u-boot.dtsi"
+#include "rk3328-sdram-ddr4-666.dtsi"
+/ {
+ chosen {
+ u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc;
+ };
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+};
+
+&pinctrl {
+ u-boot,dm-spl;
+};
+
+&sdmmc0m1_gpio {
+ u-boot,dm-spl;
+};
+
+&pcfg_pull_up_4ma {
+ u-boot,dm-spl;
+};
+
+&usb_host0_xhci {
+ vbus-supply = <&vcc_host1_5v>;
+ status = "okay";
+};
+
+/*
+ * This makes XHCI responsible for toggling VBUS. This is needed to work
+ * around an issue where either XHCI only works with USB 2.0 or OTG doesn't
+ * work, depending on how VBUS is configured. Having USB 3.0 seems better.
+ */
+&vcc_host1_5v {
+ /delete-property/ regulator-always-on;
+};
+
+/* Need this and all the pinctrl/gpio stuff above to set pinmux */
+&vcc_sd {
+ u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/rk3328-roc-cc.dts b/arch/arm/dts/rk3328-roc-cc.dts
new file mode 100644
index 0000000..8d553c9
--- /dev/null
+++ b/arch/arm/dts/rk3328-roc-cc.dts
@@ -0,0 +1,354 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+ model = "Firefly roc-rk3328-cc";
+ compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clkin: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clkin";
+ #clock-cells = <0>;
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0m1_gpio>;
+ regulator-boot-on;
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sdio: sdmmcio-regulator {
+ compatible = "regulator-gpio";
+ gpios = <&grf_gpio 0 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ regulator-name = "vcc_sdio";
+ regulator-type = "voltage";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb20_host_drv>;
+ regulator-name = "vcc_host1_5v";
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_sys: vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "firefly:blue:power";
+ linux,default-trigger = "heartbeat";
+ gpios = <&rk805 1 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ mode = <0x23>;
+ };
+
+ user {
+ label = "firefly:yellow:user";
+ linux,default-trigger = "mmc1";
+ gpios = <&rk805 0 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ mode = <0x05>;
+ };
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <150000000>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc18_emmc>;
+ status = "okay";
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_phy>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmiim1_pins>;
+ snps,aal;
+ snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ snps,rxpbl = <0x4>;
+ snps,txpbl = <0x4>;
+ tx_delay = <0x24>;
+ rx_delay = <0x18>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmiphy {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk805: pmic@18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_io>;
+ vcc6-supply = <&vcc_io>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+};
+
+&io_domains {
+ status = "okay";
+
+ vccio1-supply = <&vcc_io>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_sdio>;
+ vccio4-supply = <&vcc_18>;
+ vccio5-supply = <&vcc_io>;
+ vccio6-supply = <&vcc_io>;
+ pmuio-supply = <&vcc_io>;
+};
+
+&pinctrl {
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ usb20_host_drv: usb20-host-drv {
+ rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ max-frequency = <150000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vcc_sdio>;
+ status = "okay";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
diff --git a/board/rockchip/evb_rk3328/MAINTAINERS b/board/rockchip/evb_rk3328/MAINTAINERS
index c661d2e..89becf4 100644
--- a/board/rockchip/evb_rk3328/MAINTAINERS
+++ b/board/rockchip/evb_rk3328/MAINTAINERS
@@ -5,6 +5,13 @@
F: include/configs/evb_rk3328.h
F: configs/evb-rk3328_defconfig
+ROC-RK3328-CC
+M: Loic Devulder <ldevulder@suse.com>
+M: Chen-Yu Tsai <wens@csie.org>
+S: Maintained
+F: configs/roc-cc-rk3328_defconfig
+F: arch/arm/dts/rk3328-roc-cc-u-boot.dtsi
+
ROCK64-RK3328
M: Matwey V. Kornilov <matwey.kornilov@gmail.com>
S: Maintained
diff --git a/configs/roc-cc-rk3328_defconfig b/configs/roc-cc-rk3328_defconfig
new file mode 100644
index 0000000..933a1c6
--- /dev/null
+++ b/configs/roc-cc-rk3328_defconfig
@@ -0,0 +1,102 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_TEXT_BASE=0x00200000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_ENV_OFFSET=0x3F8000
+CONFIG_ROCKCHIP_RK3328=y
+CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_TPL_LIBCOMMON_SUPPORT=y
+CONFIG_TPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xFF130000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SMBIOS_PRODUCT_NAME="roc-rk3328-cc"
+CONFIG_DEBUG_UART=y
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
+# CONFIG_ANDROID_BOOT_IMAGE is not set
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-roc-cc.dtb"
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+CONFIG_TPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_ATF=y
+CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TIME=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_TPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="rk3328-roc-cc"
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_TPL_OF_PLATDATA=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_TPL_DM=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_TPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_TPL_SYSCON=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_FASTBOOT_BUF_ADDR=0x800800
+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_SPL_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_TPL_RAM=y
+CONFIG_DM_RESET=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYSRESET=y
+# CONFIG_TPL_SYSRESET is not set
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_SPL_TINY_MEMSET=y
+CONFIG_TPL_TINY_MEMSET=y
+CONFIG_ERRNO_STR=y
+CONFIG_SMBIOS_MANUFACTURER="firefly"
diff --git a/doc/README.rockchip b/doc/README.rockchip
index 9b699b9..70c8798 100644
--- a/doc/README.rockchip
+++ b/doc/README.rockchip
@@ -52,10 +52,12 @@
- EVB RK3308 - use evb-rk3308 configuration
- ROC-CC-RK3308 - use roc-cc-rk3308 configuration
-Two RK3328 board are supported:
+Three RK3328 boards are supported:
- EVB RK3328 - use evb-rk3328_defconfig
- Pine64 Rock64 board - use rock64-rk3328_defconfig
+ - Firefly / Libre Computer Project ROC-RK3328-CC board -
+ use roc-cc-rk3328_defconfig
Size RK3399 boards are supported (aarch64):