microblaze: timer: Prepare for device-tree initialization
Fix CONFIG_SYS_HZ usage in board config.
Do not use hardcoded value. Use CONFIG_SYS_HZ instead.
Separate static configuration to single block.
Signed-off-by: Michal Simek <monstr@monstr.eu>
diff --git a/arch/microblaze/cpu/timer.c b/arch/microblaze/cpu/timer.c
index cc6b897..1330401 100644
--- a/arch/microblaze/cpu/timer.c
+++ b/arch/microblaze/cpu/timer.c
@@ -27,42 +27,30 @@
#include <asm/microblaze_intc.h>
volatile int timestamp = 0;
+microblaze_timer_t *tmr;
-#ifdef CONFIG_SYS_TIMER_0
ulong get_timer (ulong base)
{
- return (timestamp - base);
+ if (tmr)
+ return timestamp - base;
+ return timestamp++ - base;
}
-#else
-ulong get_timer (ulong base)
-{
- return (timestamp++ - base);
-}
-#endif
-#ifdef CONFIG_SYS_TIMER_0
void __udelay(unsigned long usec)
{
- int i;
+ u32 i;
- i = get_timer(0);
- while ((get_timer(0) - i) < (usec / 1000))
- ;
+ if (tmr) {
+ i = get_timer(0);
+ while ((get_timer(0) - i) < (usec / 1000))
+ ;
+ } else {
+ for (i = 0; i < (usec * XILINX_CLOCK_FREQ / 10000000); i++)
+ ;
+ }
}
-#else
-void __udelay(unsigned long usec)
-{
- unsigned int i;
- for (i = 0; i < (usec * CONFIG_XILINX_CLOCK_FREQ / 10000000); i++)
- ;
-}
-#endif
-
-#ifdef CONFIG_SYS_TIMER_0
-microblaze_timer_t *tmr = (microblaze_timer_t *) (CONFIG_SYS_TIMER_0_ADDR);
-
-void timer_isr (void *arg)
+static void timer_isr(void *arg)
{
timestamp++;
tmr->control = tmr->control | TIMER_INTERRUPT;
@@ -70,15 +58,30 @@
int timer_init (void)
{
- tmr->loadreg = CONFIG_SYS_TIMER_0_PRELOAD;
- tmr->control = TIMER_INTERRUPT | TIMER_RESET;
- tmr->control =
- TIMER_ENABLE | TIMER_ENABLE_INTR | TIMER_RELOAD | TIMER_DOWN_COUNT;
- timestamp = 0;
- install_interrupt_handler (CONFIG_SYS_TIMER_0_IRQ, timer_isr, (void *)tmr);
+ int irq = -1;
+ u32 preload = 0;
+ u32 ret = 0;
+
+#if defined(CONFIG_SYS_TIMER_0_ADDR) && defined(CONFIG_SYS_INTC_0_NUM)
+ preload = XILINX_CLOCK_FREQ / CONFIG_SYS_HZ;
+ irq = CONFIG_SYS_TIMER_0_IRQ;
+ tmr = (microblaze_timer_t *) (CONFIG_SYS_TIMER_0_ADDR);
+#endif
+
+ if (tmr && preload && irq >= 0) {
+ tmr->loadreg = preload;
+ tmr->control = TIMER_INTERRUPT | TIMER_RESET;
+ tmr->control = TIMER_ENABLE | TIMER_ENABLE_INTR |\
+ TIMER_RELOAD | TIMER_DOWN_COUNT;
+ timestamp = 0;
+ ret = install_interrupt_handler (irq, timer_isr, (void *)tmr);
+ if (ret)
+ tmr = NULL;
+ }
+
+ /* No problem if timer is not found/initialized */
return 0;
}
-#endif
/*
* This function is derived from PowerPC code (read timebase as long long).
diff --git a/arch/microblaze/include/asm/microblaze_timer.h b/arch/microblaze/include/asm/microblaze_timer.h
index 844c8db..28e8b02 100644
--- a/arch/microblaze/include/asm/microblaze_timer.h
+++ b/arch/microblaze/include/asm/microblaze_timer.h
@@ -39,3 +39,6 @@
int loadreg; /* load register TLR */
int counter; /* timer/counter register */
} microblaze_timer_t;
+
+int timer_init(void);
+
diff --git a/arch/microblaze/lib/board.c b/arch/microblaze/lib/board.c
index b5f21d8..fde109f 100644
--- a/arch/microblaze/lib/board.c
+++ b/arch/microblaze/lib/board.c
@@ -42,9 +42,6 @@
#ifdef CONFIG_SYS_GPIO_0
extern int gpio_init (void);
#endif
-#ifdef CONFIG_SYS_TIMER_0
-extern int timer_init (void);
-#endif
#ifdef CONFIG_SYS_FSL_2
extern void fsl_init2 (void);
#endif
@@ -74,9 +71,7 @@
gpio_init,
#endif
interrupts_init,
-#ifdef CONFIG_SYS_TIMER_0
timer_init,
-#endif
#ifdef CONFIG_SYS_FSL_2
fsl_init2,
#endif