blob: fe20363e690f7e32de12ebbb6d6f93d112f10e47 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2019-2020 NXP
*/
#ifndef __LS1028A_QDS_H
#define __LS1028A_QDS_H
#include "ls1028a_common.h"
#define CONFIG_SYS_CLK_FREQ 100000000
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)
/* DDR */
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_QIXIS_I2C_ACCESS
/*
* QIXIS Definitions
*/
#define CONFIG_FSL_QIXIS
#ifdef CONFIG_FSL_QIXIS
#define QIXIS_BASE 0x7fb00000
#define QIXIS_BASE_PHYS QIXIS_BASE
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_SWITCH 1
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SHIFT 5
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x00
#define QIXIS_LBMAP_SD 0x00
#define QIXIS_LBMAP_EMMC 0x00
#define QIXIS_LBMAP_QSPI 0x00
#define QIXIS_RCW_SRC_SD 0x8
#define QIXIS_RCW_SRC_EMMC 0x9
#define QIXIS_RCW_SRC_QSPI 0xf
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#define QIXIS_RST_FORCE_MEM 0x01
#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
CSPR_PORT_SIZE_8 | \
CSPR_MSEL_GPCM | \
CSPR_V)
#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
CSOR_NOR_NOR_MODE_AVD_NOR | \
CSOR_NOR_TRHZ_80)
#endif
/* RTC */
#define CONFIG_SYS_RTC_BUS_NUM 1
#define I2C_MUX_CH_RTC 0xB
/* Store environment at top of flash */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#endif
/* LPUART */
#ifdef CONFIG_LPUART
#define CONFIG_LPUART_32B_REG
#define CFG_LPUART_MUX_MASK 0xf0
#define CFG_LPUART_EN 0xf0
#endif
/* SATA */
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#ifndef SPL_NO_ENV
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"board=ls1028aqds\0" \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_addr=0x00f00000\0" \
"kernel_addr=0x01000000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"load_addr=0xa0000000\0" \
"kernel_addr_r=0x81000000\0" \
"fdt_addr_r=0x90000000\0" \
"fdt2_addr_r=0x90010000\0" \
"ramdisk_addr_r=0xa0000000\0" \
"kernel_start=0x1000000\0" \
"kernelheader_start=0x600000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernelheader_size=0x40000\0" \
"kernel_addr_sd=0x8000\0" \
"kernel_size_sd=0x14000\0" \
"kernelhdr_addr_sd=0x3000\0" \
"kernelhdr_size_sd=0x10\0" \
"console=ttyS0,115200\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
BOOTENV \
"boot_scripts=ls1028aqds_boot.scr\0" \
"boot_script_hdr=hdr_ls1028aqds_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"xspi_bootcmd=echo Trying load from FlexSPI flash ...;" \
"sf probe 0:0 && sf read $load_addr " \
"$kernel_start $kernel_size ; env exists secureboot &&" \
"sf read $kernelheader_addr_r $kernelheader_start " \
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
" bootm $load_addr#$board\0" \
"xspi_hdploadcmd=echo Trying load HDP firmware from FlexSPI...;" \
"sf probe 0:0 && sf read $load_addr 0x940000 0x30000 " \
"&& hdp load $load_addr 0x2000\0" \
"sd_bootcmd=echo Trying load from SD ...;" \
"mmc dev 0; mmcinfo; mmc read $load_addr " \
"$kernel_addr_sd $kernel_size_sd && " \
"env exists secureboot && mmc read $kernelheader_addr_r " \
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
" && esbc_validate ${kernelheader_addr_r};" \
"bootm $load_addr#$board\0" \
"sd_hdploadcmd=echo Trying load HDP firmware from SD..;" \
"mmc dev 0;mmcinfo; mmc read $load_addr 0x4a00 0x200 " \
"&& hdp load $load_addr 0x2000\0" \
"emmc_bootcmd=echo Trying load from EMMC ..;" \
"mmc dev 1; mmcinfo; mmc read $load_addr " \
"$kernel_addr_sd $kernel_size_sd && " \
"env exists secureboot && mmc read $kernelheader_addr_r " \
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
" && esbc_validate ${kernelheader_addr_r};" \
"bootm $load_addr#$board\0" \
"emmc_hdploadcmd=echo Trying load HDP firmware from EMMC..;" \
"mmc dev 1;mmcinfo;mmc read $load_addr 0x4a00 0x200 " \
"&& hdp load $load_addr 0x2000\0"
#endif
#endif /* __LS1028A_QDS_H */