odroid: add board file for Odroid X2/U3 based on Samsung Exynos4412
This board file supports standard features of Odroid X2 and U3 boards:
- Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to 800MHz,
- MAX77686 power regulator,
- USB PHY,
- enable XCL205 - power for board peripherials
- check board type: U3 or X2.
- enable Odroid U3 FAN cooler
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
diff --git a/board/samsung/odroid/odroid.c b/board/samsung/odroid/odroid.c
new file mode 100644
index 0000000..ac19527
--- /dev/null
+++ b/board/samsung/odroid/odroid.c
@@ -0,0 +1,470 @@
+/*
+ * Copyright (C) 2014 Samsung Electronics
+ * Przemyslaw Marczak <p.marczak@samsung.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include <asm/arch/cpu.h>
+#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <errno.h>
+#include <usb.h>
+#include <usb/s3c_udc.h>
+#include <samsung/misc.h>
+#include "setup.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_BOARD_TYPES
+/* Odroid board types */
+enum {
+ ODROID_TYPE_U3,
+ ODROID_TYPE_X2,
+ ODROID_TYPES,
+};
+
+void set_board_type(void)
+{
+ /* Set GPA1 pin 1 to HI - enable XCL205 output */
+ writel(XCL205_EN_GPIO_CON_CFG, XCL205_EN_GPIO_CON);
+ writel(XCL205_EN_GPIO_DAT_CFG, XCL205_EN_GPIO_CON + 0x4);
+ writel(XCL205_EN_GPIO_PUD_CFG, XCL205_EN_GPIO_CON + 0x8);
+ writel(XCL205_EN_GPIO_DRV_CFG, XCL205_EN_GPIO_CON + 0xc);
+
+ /* Set GPC1 pin 2 to IN - check XCL205 output state */
+ writel(XCL205_STATE_GPIO_CON_CFG, XCL205_STATE_GPIO_CON);
+ writel(XCL205_STATE_GPIO_PUD_CFG, XCL205_STATE_GPIO_CON + 0x8);
+
+ /* XCL205 - needs some latch time */
+ sdelay(200000);
+
+ /* Check GPC1 pin2 - LED supplied by XCL205 - X2 only */
+ if (readl(XCL205_STATE_GPIO_DAT) & (1 << XCL205_STATE_GPIO_PIN))
+ gd->board_type = ODROID_TYPE_X2;
+ else
+ gd->board_type = ODROID_TYPE_U3;
+}
+
+const char *get_board_type(void)
+{
+ const char *board_type[] = {"u3", "x2"};
+
+ return board_type[gd->board_type];
+}
+#endif
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+char *get_dfu_alt_system(void)
+{
+ return getenv("dfu_alt_system");
+}
+
+char *get_dfu_alt_boot(void)
+{
+ char *alt_boot;
+
+ switch (get_boot_mode()) {
+ case BOOT_MODE_SD:
+ alt_boot = CONFIG_DFU_ALT_BOOT_SD;
+ break;
+ case BOOT_MODE_EMMC:
+ case BOOT_MODE_EMMC_SD:
+ alt_boot = CONFIG_DFU_ALT_BOOT_EMMC;
+ break;
+ default:
+ alt_boot = NULL;
+ break;
+ }
+ return alt_boot;
+}
+#endif
+
+static void board_clock_init(void)
+{
+ unsigned int set, clr, clr_src_cpu, clr_pll_con0, clr_src_dmc;
+ struct exynos4x12_clock *clk = (struct exynos4x12_clock *)
+ samsung_get_base_clock();
+
+ /*
+ * CMU_CPU clocks src to MPLL
+ * Bit values: 0 ; 1
+ * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL
+ * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL
+ * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C
+ * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL
+ */
+ clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1) |
+ MUX_HPM_SEL(1) | MUX_MPLL_USER_SEL_C(1);
+ set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1) | MUX_HPM_SEL(1) |
+ MUX_MPLL_USER_SEL_C(1);
+
+ clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
+
+ /* Wait for mux change */
+ while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
+ continue;
+
+ /* Set APLL to 1000MHz */
+ clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1);
+ set = SDIV(0) | PDIV(3) | MDIV(125) | FSEL(1);
+
+ clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set);
+
+ /* Wait for PLL to be locked */
+ while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT))
+ continue;
+
+ /* Set CMU_CPU clocks src to APLL */
+ set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0) | MUX_HPM_SEL(0) |
+ MUX_MPLL_USER_SEL_C(1);
+ clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
+
+ /* Wait for mux change */
+ while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
+ continue;
+
+ set = CORE_RATIO(0) | COREM0_RATIO(2) | COREM1_RATIO(5) |
+ PERIPH_RATIO(0) | ATB_RATIO(4) | PCLK_DBG_RATIO(1) |
+ APLL_RATIO(0) | CORE2_RATIO(0);
+ /*
+ * Set dividers for MOUTcore = 1000 MHz
+ * coreout = MOUT / (ratio + 1) = 1000 MHz (0)
+ * corem0 = armclk / (ratio + 1) = 333 MHz (2)
+ * corem1 = armclk / (ratio + 1) = 166 MHz (5)
+ * periph = armclk / (ratio + 1) = 1000 MHz (0)
+ * atbout = MOUT / (ratio + 1) = 200 MHz (4)
+ * pclkdbgout = atbout / (ratio + 1) = 100 MHz (1)
+ * sclkapll = MOUTapll / (ratio + 1) = 1000 MHz (0)
+ * core2out = core_out / (ratio + 1) = 1000 MHz (0) (armclk)
+ */
+ clr = CORE_RATIO(7) | COREM0_RATIO(7) | COREM1_RATIO(7) |
+ PERIPH_RATIO(7) | ATB_RATIO(7) | PCLK_DBG_RATIO(7) |
+ APLL_RATIO(7) | CORE2_RATIO(7);
+
+ clrsetbits_le32(&clk->div_cpu0, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING)
+ continue;
+
+ /*
+ * For MOUThpm = 1000 MHz (MOUTapll)
+ * doutcopy = MOUThpm / (ratio + 1) = 200 (4)
+ * sclkhpm = doutcopy / (ratio + 1) = 200 (4)
+ * cores_out = armclk / (ratio + 1) = 1000 (0)
+ */
+ clr = COPY_RATIO(7) | HPM_RATIO(7) | CORES_RATIO(7);
+ set = COPY_RATIO(4) | HPM_RATIO(4) | CORES_RATIO(0);
+
+ clrsetbits_le32(&clk->div_cpu1, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_cpu1) & DIV_STAT_CPU1_CHANGING)
+ continue;
+
+ /*
+ * Set CMU_DMC clocks src to APLL
+ * Bit values: 0 ; 1
+ * MUX_C2C_SEL: SCLKMPLL ; SCLKAPLL
+ * MUX_DMC_BUS_SEL: SCLKMPLL ; SCLKAPLL
+ * MUX_DPHY_SEL: SCLKMPLL ; SCLKAPLL
+ * MUX_MPLL_SEL: FINPLL ; MOUT_MPLL_FOUT
+ * MUX_PWI_SEL: 0110 (MPLL); 0111 (EPLL); 1000 (VPLL); 0(XXTI)
+ * MUX_G2D_ACP0_SEL: SCLKMPLL ; SCLKAPLL
+ * MUX_G2D_ACP1_SEL: SCLKEPLL ; SCLKVPLL
+ * MUX_G2D_ACP_SEL: OUT_ACP0 ; OUT_ACP1
+ */
+ clr_src_dmc = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) |
+ MUX_DPHY_SEL(1) | MUX_MPLL_SEL(1) |
+ MUX_PWI_SEL(15) | MUX_G2D_ACP0_SEL(1) |
+ MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);
+ set = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) | MUX_DPHY_SEL(1) |
+ MUX_MPLL_SEL(0) | MUX_PWI_SEL(0) | MUX_G2D_ACP0_SEL(1) |
+ MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);
+
+ clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);
+
+ /* Wait for mux change */
+ while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
+ continue;
+
+ /* Set MPLL to 800MHz */
+ set = SDIV(0) | PDIV(3) | MDIV(100) | FSEL(0) | PLL_ENABLE(1);
+
+ clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set);
+
+ /* Wait for PLL to be locked */
+ while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT))
+ continue;
+
+ /* Switch back CMU_DMC mux */
+ set = MUX_C2C_SEL(0) | MUX_DMC_BUS_SEL(0) | MUX_DPHY_SEL(0) |
+ MUX_MPLL_SEL(1) | MUX_PWI_SEL(8) | MUX_G2D_ACP0_SEL(0) |
+ MUX_G2D_ACP1_SEL(0) | MUX_G2D_ACP_SEL(0);
+
+ clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);
+
+ /* Wait for mux change */
+ while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
+ continue;
+
+ /* CLK_DIV_DMC0 */
+ clr = ACP_RATIO(7) | ACP_PCLK_RATIO(7) | DPHY_RATIO(7) |
+ DMC_RATIO(7) | DMCD_RATIO(7) | DMCP_RATIO(7);
+ /*
+ * For:
+ * MOUTdmc = 800 MHz
+ * MOUTdphy = 800 MHz
+ *
+ * aclk_acp = MOUTdmc / (ratio + 1) = 200 (3)
+ * pclk_acp = aclk_acp / (ratio + 1) = 100 (1)
+ * sclk_dphy = MOUTdphy / (ratio + 1) = 400 (1)
+ * sclk_dmc = MOUTdmc / (ratio + 1) = 400 (1)
+ * aclk_dmcd = sclk_dmc / (ratio + 1) = 200 (1)
+ * aclk_dmcp = aclk_dmcd / (ratio + 1) = 100 (1)
+ */
+ set = ACP_RATIO(3) | ACP_PCLK_RATIO(1) | DPHY_RATIO(1) |
+ DMC_RATIO(1) | DMCD_RATIO(1) | DMCP_RATIO(1);
+
+ clrsetbits_le32(&clk->div_dmc0, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_dmc0) & DIV_STAT_DMC0_CHANGING)
+ continue;
+
+ /* CLK_DIV_DMC1 */
+ clr = G2D_ACP_RATIO(15) | C2C_RATIO(7) | PWI_RATIO(15) |
+ C2C_ACLK_RATIO(7) | DVSEM_RATIO(127) | DPM_RATIO(127);
+ /*
+ * For:
+ * MOUTg2d = 800 MHz
+ * MOUTc2c = 800 Mhz
+ * MOUTpwi = 108 MHz
+ *
+ * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 400 (1)
+ * sclk_c2c = MOUTc2c / (ratio + 1) = 400 (1)
+ * aclk_c2c = sclk_c2c / (ratio + 1) = 200 (1)
+ * sclk_pwi = MOUTpwi / (ratio + 1) = 18 (5)
+ */
+ set = G2D_ACP_RATIO(1) | C2C_RATIO(1) | PWI_RATIO(5) |
+ C2C_ACLK_RATIO(1) | DVSEM_RATIO(1) | DPM_RATIO(1);
+
+ clrsetbits_le32(&clk->div_dmc1, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_dmc1) & DIV_STAT_DMC1_CHANGING)
+ continue;
+
+ /* CLK_SRC_PERIL0 */
+ clr = UART0_SEL(15) | UART1_SEL(15) | UART2_SEL(15) |
+ UART3_SEL(15) | UART4_SEL(15);
+ /*
+ * Set CLK_SRC_PERIL0 clocks src to MPLL
+ * src values: 0(XXTI); 1(XusbXTI); 2(SCLK_HDMI24M); 3(SCLK_USBPHY0);
+ * 5(SCLK_HDMIPHY); 6(SCLK_MPLL_USER_T); 7(SCLK_EPLL);
+ * 8(SCLK_VPLL)
+ *
+ * Set all to SCLK_MPLL_USER_T
+ */
+ set = UART0_SEL(6) | UART1_SEL(6) | UART2_SEL(6) | UART3_SEL(6) |
+ UART4_SEL(6);
+
+ clrsetbits_le32(&clk->src_peril0, clr, set);
+
+ /* CLK_DIV_PERIL0 */
+ clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) |
+ UART3_RATIO(15) | UART4_RATIO(15);
+ /*
+ * For MOUTuart0-4: 800MHz
+ *
+ * SCLK_UARTx = MOUTuartX / (ratio + 1) = 100 (7)
+ */
+ set = UART0_RATIO(7) | UART1_RATIO(7) | UART2_RATIO(7) |
+ UART3_RATIO(7) | UART4_RATIO(7);
+
+ clrsetbits_le32(&clk->div_peril0, clr, set);
+
+ while (readl(&clk->div_stat_peril0) & DIV_STAT_PERIL0_CHANGING)
+ continue;
+
+ /* CLK_DIV_FSYS1 */
+ clr = MMC0_RATIO(15) | MMC0_PRE_RATIO(255) | MMC1_RATIO(15) |
+ MMC1_PRE_RATIO(255);
+ /*
+ * For MOUTmmc0-3 = 800 MHz (MPLL)
+ *
+ * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 100 (7)
+ * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 50 (1)
+ * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 100 (7)
+ * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 50 (1)
+ */
+ set = MMC0_RATIO(7) | MMC0_PRE_RATIO(1) | MMC1_RATIO(7) |
+ MMC1_PRE_RATIO(1);
+
+ clrsetbits_le32(&clk->div_fsys1, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING)
+ continue;
+
+ /* CLK_DIV_FSYS2 */
+ clr = MMC2_RATIO(15) | MMC2_PRE_RATIO(255) | MMC3_RATIO(15) |
+ MMC3_PRE_RATIO(255);
+ /*
+ * For MOUTmmc0-3 = 800 MHz (MPLL)
+ *
+ * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 100 (7)
+ * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 50 (1)
+ * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 100 (7)
+ * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 50 (1)
+ */
+ set = MMC2_RATIO(7) | MMC2_PRE_RATIO(1) | MMC3_RATIO(7) |
+ MMC3_PRE_RATIO(1);
+
+ clrsetbits_le32(&clk->div_fsys2, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_fsys2) & DIV_STAT_FSYS2_CHANGING)
+ continue;
+
+ /* CLK_DIV_FSYS3 */
+ clr = MMC4_RATIO(15) | MMC4_PRE_RATIO(255);
+ /*
+ * For MOUTmmc4 = 800 MHz (MPLL)
+ *
+ * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 100 (7)
+ * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 100 (0)
+ */
+ set = MMC4_RATIO(7) | MMC4_PRE_RATIO(0);
+
+ clrsetbits_le32(&clk->div_fsys3, clr, set);
+
+ /* Wait for divider ready status */
+ while (readl(&clk->div_stat_fsys3) & DIV_STAT_FSYS3_CHANGING)
+ continue;
+
+ return;
+}
+
+static void board_gpio_init(void)
+{
+ /* eMMC Reset Pin */
+ gpio_cfg_pin(EXYNOS4X12_GPIO_K12, S5P_GPIO_FUNC(0x1));
+ gpio_set_pull(EXYNOS4X12_GPIO_K12, S5P_GPIO_PULL_NONE);
+ gpio_set_drv(EXYNOS4X12_GPIO_K12, S5P_GPIO_DRV_4X);
+
+ /* Enable FAN (Odroid U3) */
+ gpio_set_pull(EXYNOS4X12_GPIO_D00, S5P_GPIO_PULL_UP);
+ gpio_set_drv(EXYNOS4X12_GPIO_D00, S5P_GPIO_DRV_4X);
+ gpio_direction_output(EXYNOS4X12_GPIO_D00, 1);
+
+ /* OTG Vbus output (Odroid U3+) */
+ gpio_set_pull(EXYNOS4X12_GPIO_L20, S5P_GPIO_PULL_NONE);
+ gpio_set_drv(EXYNOS4X12_GPIO_L20, S5P_GPIO_DRV_4X);
+ gpio_direction_output(EXYNOS4X12_GPIO_L20, 0);
+
+ /* OTG INT (Odroid U3+) */
+ gpio_set_pull(EXYNOS4X12_GPIO_X31, S5P_GPIO_PULL_UP);
+ gpio_set_drv(EXYNOS4X12_GPIO_X31, S5P_GPIO_DRV_4X);
+ gpio_direction_input(EXYNOS4X12_GPIO_X31);
+}
+
+static int pmic_init_max77686(void)
+{
+ struct pmic *p = pmic_get("MAX77686_PMIC");
+
+ if (pmic_probe(p))
+ return -ENODEV;
+
+ /* Set LDO Voltage */
+ max77686_set_ldo_voltage(p, 20, 1800000); /* LDO20 eMMC */
+ max77686_set_ldo_voltage(p, 21, 2800000); /* LDO21 SD */
+ max77686_set_ldo_voltage(p, 22, 2800000); /* LDO22 eMMC */
+
+ return 0;
+}
+
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+static void board_init_i2c(void)
+{
+ /* I2C_0 */
+ if (exynos_pinmux_config(PERIPH_ID_I2C0, PINMUX_FLAG_NONE))
+ debug("I2C%d not configured\n", (I2C_0));
+}
+#endif
+
+int exynos_early_init_f(void)
+{
+ board_clock_init();
+ board_gpio_init();
+
+ return 0;
+}
+
+int exynos_init(void)
+{
+ /* The last MB of memory is reserved for secure firmware */
+ gd->ram_size -= SZ_1M;
+ gd->bd->bi_dram[CONFIG_NR_DRAM_BANKS - 1].size -= SZ_1M;
+
+ return 0;
+}
+
+int exynos_power_init(void)
+{
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ board_init_i2c();
+#endif
+ pmic_init(I2C_0);
+ pmic_init_max77686();
+
+ return 0;
+}
+
+#ifdef CONFIG_USB_GADGET
+static int s5pc210_phy_control(int on)
+{
+ struct pmic *p_pmic;
+
+ p_pmic = pmic_get("MAX77686_PMIC");
+ if (!p_pmic)
+ return -ENODEV;
+
+ if (pmic_probe(p_pmic))
+ return -1;
+
+ if (on)
+ return max77686_set_ldo_mode(p_pmic, 12, OPMODE_ON);
+ else
+ return max77686_set_ldo_mode(p_pmic, 12, OPMODE_LPM);
+}
+
+struct s3c_plat_otg_data s5pc210_otg_data = {
+ .phy_control = s5pc210_phy_control,
+ .regs_phy = EXYNOS4X12_USBPHY_BASE,
+ .regs_otg = EXYNOS4X12_USBOTG_BASE,
+ .usb_phy_ctrl = EXYNOS4X12_USBPHY_CONTROL,
+ .usb_flags = PHY0_SLEEP,
+};
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+ debug("USB_udc_probe\n");
+ return s3c_udc_probe(&s5pc210_otg_data);
+}
+#endif
+
+void reset_misc(void)
+{
+ /* Reset eMMC*/
+ gpio_set_value(EXYNOS4X12_GPIO_K12, 0);
+ mdelay(10);
+ gpio_set_value(EXYNOS4X12_GPIO_K12, 1);
+}