ppc4xx: Update configs for Netstal boards
I reorganized my config files, putting the common stuff into netstal-common.h
(got the idea by looking a amcc-common.h from Stefan).
Added stuff to boot the new powerpc linux via NFS (only tested with HCU4).
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h
index e448969..5f31198 100644
--- a/include/configs/mcu25.h
+++ b/include/configs/mcu25.h
@@ -35,6 +35,12 @@
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405GP 1
#define CONFIG_4xx 1
+#define CONFIG_HOSTNAME mcu25
+
+/*
+ * Include common defines/options for all boards produced by Netstal Maschinen
+ */
+#include "netstal-common.h"
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
@@ -80,8 +86,6 @@
* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#define CONFIG_SERIAL_MULTI 1
/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */
#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CONFIG_SYS_BASE_BAUD 691200
@@ -95,10 +99,6 @@
/* Set console baudrate to 9600 */
#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Flash
*----------------------------------------------------------------------*/
@@ -149,74 +149,13 @@
*----------------------------------------------------------------------*/
#define CONFIG_SYS_SPD_BUS_NUM 0
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/* This is the 7bit address of the device, not including P. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#undef CONFIG_SYS_I2C_MULTI_EEPROMS
-
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
/* Setup some board specific values for the default environment variables */
-#define CONFIG_HOSTNAME mcu25
-#define CONFIG_IPADDR 172.25.1.99
-#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_SERVERIP 172.25.1.3
+#define CONFIG_IPADDR 172.25.1.25
-#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "loadaddr=0x01000000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/home/diagnose/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/mcu25/uImage\0" \
- "load=tftp 100000 mcu25/u-boot.bin\0" \
- "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \
- "cp.b 100000 FFFB0000 50000\0" \
- "upd=run load;run update\0" \
- "vx_rom=mcu25/mcu25_vx_rom\0" \
- "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \
- "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \
- " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_NETSTAL_DEF_ENV \
+ CONFIG_NETSTAL_DEF_ENV_POWERPC \
""
-#define CONFIG_BOOTCOMMAND "run vx"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 1 /* PHY address */
-
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descr */
/*
* BOOTP options
@@ -285,13 +224,6 @@
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
@@ -353,8 +285,4 @@
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */