AT91CAP9ADK: hook up the ATMEL LCD driver
This patch makes the necessary adaptations (PIO configurations and
defines in config header file) to hook up the Atmel LCD driver to the
AT91CAP9ADK board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/atmel/at91cap9adk/at91cap9adk.c b/board/atmel/at91cap9adk/at91cap9adk.c
index 67e16bb..e353cea 100644
--- a/board/atmel/at91cap9adk/at91cap9adk.c
+++ b/board/atmel/at91cap9adk/at91cap9adk.c
@@ -30,6 +30,8 @@
#include <asm/arch/at91_rstc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/io.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
@@ -233,6 +235,65 @@
}
#endif
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_clk: 4965000,
+ vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
+ ATMEL_LCDC_INVFRAME_INVERTED,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 5,
+ vl_left_margin: 1,
+ vl_right_margin:33,
+ vl_vsync_len: 1,
+ vl_upper_margin:1,
+ vl_lower_margin:0,
+ mmio: AT91CAP9_LCDC_BASE,
+};
+
+void lcd_enable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PC0, 0); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PC0, 1); /* power down */
+}
+
+static void at91cap9_lcd_hw_init(void)
+{
+ at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
+ at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
+ at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
+ at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
+ at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
+ at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
+ at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
+ at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
+ at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
+ at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
+ at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
+ at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
+ at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
+ at91_set_A_periph(AT91_PIN_PC17, 0); /* LCDD13 */
+ at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
+ at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
+ at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
+ at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
+ at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
+ at91_set_A_periph(AT91_PIN_PC25, 0); /* LCDD21 */
+ at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
+ at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
+
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_LCDC);
+
+ gd->fb_base = 0;
+}
+#endif
+
int board_init(void)
{
/* Enable Ctrlc */
@@ -257,6 +318,9 @@
#ifdef CONFIG_USB_OHCI_NEW
at91cap9_uhp_hw_init();
#endif
+#ifdef CONFIG_LCD
+ at91cap9_lcd_hw_init();
+#endif
return 0;
}