NAND: Update nand_spl driver to match updated nand subsystem
This patch changes the NAND booting driver nand_spl/nand_boot.c to match
the new infrastructure from the updated NAND subsystem. This NAND
subsystem was recently synced again with the Linux 2.6.22 MTD/NAND
subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/nand_spl/nand_boot.c b/nand_spl/nand_boot.c
index 563a80b..5914d04 100644
--- a/nand_spl/nand_boot.c
+++ b/nand_spl/nand_boot.c
@@ -20,6 +20,7 @@
#include <common.h>
#include <nand.h>
+#include <asm/io.h>
#define CFG_NAND_READ_DELAY \
{ volatile int dummy; int i; for (i=0; i<10000; i++) dummy = i; }
@@ -36,34 +37,37 @@
{
struct nand_chip *this = mtd->priv;
int page_addr = page + block * CFG_NAND_PAGE_COUNT;
+ int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
if (this->dev_ready)
- this->dev_ready(mtd);
+ while (!this->dev_ready(mtd))
+ ;
else
CFG_NAND_READ_DELAY;
/* Begin command latch cycle */
- this->hwcontrol(mtd, NAND_CTL_SETCLE);
- this->write_byte(mtd, cmd);
+ this->cmd_ctrl(mtd, cmd, ctrl);
/* Set ALE and clear CLE to start address cycle */
- this->hwcontrol(mtd, NAND_CTL_CLRCLE);
- this->hwcontrol(mtd, NAND_CTL_SETALE);
+ ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
/* Column address */
- this->write_byte(mtd, offs); /* A[7:0] */
- this->write_byte(mtd, (uchar)(page_addr & 0xff)); /* A[16:9] */
- this->write_byte(mtd, (uchar)((page_addr >> 8) & 0xff)); /* A[24:17] */
+ this->cmd_ctrl(mtd, offs, ctrl);
+ ctrl &= ~NAND_CTRL_CHANGE;
+ this->cmd_ctrl(mtd, (u8)(page_addr & 0xff), ctrl); /* A[16:9] */
+ ctrl &= ~NAND_CTRL_CHANGE;
+ this->cmd_ctrl(mtd, (u8)((page_addr >> 8) & 0xff), ctrl); /* A[24:17] */
#ifdef CFG_NAND_4_ADDR_CYCLE
/* One more address cycle for devices > 32MiB */
- this->write_byte(mtd, (uchar)((page_addr >> 16) & 0x0f)); /* A[xx:25] */
+ this->cmd_ctrl(mtd, (u8)((page_addr >> 16) & 0x0f), ctrl); /* A[xx:25] */
#endif
/* Latch in address */
- this->hwcontrol(mtd, NAND_CTL_CLRALE);
+ this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
* Wait a while for the data to be ready
*/
if (this->dev_ready)
- this->dev_ready(mtd);
+ while (!this->dev_ready(mtd))
+ ;
else
CFG_NAND_READ_DELAY;
@@ -137,7 +141,7 @@
/*
* Read one byte
*/
- if (this->read_byte(mtd) != 0xff)
+ if (in_8(this->IO_ADDR_R) != 0xff)
return 1;
return 0;
@@ -166,9 +170,9 @@
oob_data = ecc_calc + 0x200;
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
- this->enable_hwecc(mtd, NAND_ECC_READ);
+ this->ecc.hwctl(mtd, NAND_ECC_READ);
this->read_buf(mtd, p, eccsize);
- this->calculate_ecc(mtd, p, &ecc_calc[i]);
+ this->ecc.calculate(mtd, p, &ecc_calc[i]);
}
this->read_buf(mtd, oob_data, CFG_NAND_OOBSIZE);
@@ -184,7 +188,7 @@
* from correct_data(). We just hope that all possible errors
* are corrected by this routine.
*/
- stat = this->correct_data(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ stat = this->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
}
return 0;