sf: Fix quad bit set for micron devices
Setting up quad bit for micron devices need to do the
same way as other flash devices like spansion, winbond
etc does using enhanced volatile config register so this
patch adds this support instead of printing "QEB is volatile"
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Peter Pan <peterpandong@micron.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c
index e4b8ce9..d9124c5 100644
--- a/drivers/mtd/spi/spi_flash.c
+++ b/drivers/mtd/spi/spi_flash.c
@@ -111,6 +111,37 @@
}
#endif
+#ifdef CONFIG_SPI_FLASH_STMICRO
+static int read_evcr(struct spi_flash *flash, u8 *evcr)
+{
+ int ret;
+ const u8 cmd = CMD_READ_EVCR;
+
+ ret = spi_flash_read_common(flash, &cmd, 1, evcr, 1);
+ if (ret < 0) {
+ debug("SF: error reading EVCR\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int write_evcr(struct spi_flash *flash, u8 evcr)
+{
+ u8 cmd;
+ int ret;
+
+ cmd = CMD_WRITE_EVCR;
+ ret = spi_flash_write_common(flash, &cmd, 1, &evcr, 1);
+ if (ret < 0) {
+ debug("SF: error while writing EVCR register\n");
+ return ret;
+ }
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_SPI_FLASH_BAR
static int spi_flash_write_bar(struct spi_flash *flash, u32 offset)
{
@@ -843,6 +874,34 @@
}
#endif
+#ifdef CONFIG_SPI_FLASH_STMICRO
+static int micron_quad_enable(struct spi_flash *flash)
+{
+ u8 qeb_status;
+ int ret;
+
+ ret = read_evcr(flash, &qeb_status);
+ if (ret < 0)
+ return ret;
+
+ if (!(qeb_status & STATUS_QEB_MICRON))
+ return 0;
+
+ ret = write_evcr(flash, qeb_status & ~STATUS_QEB_MICRON);
+ if (ret < 0)
+ return ret;
+
+ /* read EVCR and check it */
+ ret = read_evcr(flash, &qeb_status);
+ if (!(ret >= 0 && !(qeb_status & STATUS_QEB_MICRON))) {
+ printf("SF: Micron EVCR Quad bit not clear\n");
+ return -EINVAL;
+ }
+
+ return ret;
+}
+#endif
+
static int set_quad_mode(struct spi_flash *flash, u8 idcode0)
{
switch (idcode0) {
@@ -857,8 +916,7 @@
#endif
#ifdef CONFIG_SPI_FLASH_STMICRO
case SPI_FLASH_CFI_MFR_STMICRO:
- debug("SF: QEB is volatile for %02x flash\n", idcode0);
- return 0;
+ return micron_quad_enable(flash);
#endif
default:
printf("SF: Need set QEB func for %02x flash\n", idcode0);