armv8/ls1043ardb: Add sd boot support
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/ls1043ardb/README b/board/freescale/ls1043ardb/README
index 4f15557..0556e73 100644
--- a/board/freescale/ls1043ardb/README
+++ b/board/freescale/ls1043ardb/README
@@ -84,3 +84,4 @@
---------------
a) NOR boot
b) NAND boot
+c) SD boot
diff --git a/board/freescale/ls1043ardb/cpld.c b/board/freescale/ls1043ardb/cpld.c
index f29383d..78c2824 100644
--- a/board/freescale/ls1043ardb/cpld.c
+++ b/board/freescale/ls1043ardb/cpld.c
@@ -61,6 +61,21 @@
CPLD_WRITE(system_rst, 1);
}
+void cpld_set_sd(void)
+{
+ u16 reg = CPLD_CFG_RCW_SRC_SD;
+ u8 reg5 = (u8)(reg >> 1);
+ u8 reg6 = (u8)(reg & 1);
+
+ cpld_rev_bit(®5);
+
+ CPLD_WRITE(soft_mux_on, 1);
+
+ CPLD_WRITE(cfg_rcw_src1, reg5);
+ CPLD_WRITE(cfg_rcw_src2, reg6);
+
+ CPLD_WRITE(system_rst, 1);
+}
#ifdef DEBUG
static void cpld_dump_regs(void)
{
@@ -109,6 +124,8 @@
cpld_set_altbank();
else if (strcmp(argv[2], "nand") == 0)
cpld_set_nand();
+ else if (strcmp(argv[2], "sd") == 0)
+ cpld_set_sd();
else
cpld_set_defbank();
#ifdef DEBUG
@@ -128,6 +145,7 @@
"reset: reset to default bank\n"
"cpld reset altbank: reset to alternate bank\n"
"cpld reset nand: reset to boot from NAND flash\n"
+ "cpld reset sd: reset to boot from SD card\n"
#ifdef DEBUG
"cpld dump - display the CPLD registers\n"
#endif
diff --git a/board/freescale/ls1043ardb/cpld.h b/board/freescale/ls1043ardb/cpld.h
index 5f43a8a..bd59c0e 100644
--- a/board/freescale/ls1043ardb/cpld.h
+++ b/board/freescale/ls1043ardb/cpld.h
@@ -41,4 +41,5 @@
#define CPLD_BANK_SEL_MASK 0x07
#define CPLD_BANK_SEL_ALTBANK 0x04
#define CPLD_CFG_RCW_SRC_NAND 0x106
+#define CPLD_CFG_RCW_SRC_SD 0x040
#endif
diff --git a/board/freescale/ls1043ardb/ls1043ardb.c b/board/freescale/ls1043ardb/ls1043ardb.c
index 461a195..9032ed3 100644
--- a/board/freescale/ls1043ardb/ls1043ardb.c
+++ b/board/freescale/ls1043ardb/ls1043ardb.c
@@ -25,12 +25,17 @@
int checkboard(void)
{
static const char *freq[3] = {"100.00MHZ", "156.25MHZ"};
+#ifndef CONFIG_SD_BOOT
u8 cfg_rcw_src1, cfg_rcw_src2;
u32 cfg_rcw_src;
+#endif
u32 sd1refclk_sel;
printf("Board: LS1043ARDB, boot from ");
+#ifdef CONFIG_SD_BOOT
+ puts("SD\n");
+#else
cfg_rcw_src1 = CPLD_READ(cfg_rcw_src1);
cfg_rcw_src2 = CPLD_READ(cfg_rcw_src2);
cpld_rev_bit(&cfg_rcw_src1);
@@ -43,6 +48,7 @@
puts("NAND\n");
else
printf("Invalid setting of SW4\n");
+#endif
printf("CPLD: V%x.%x\nPCBA: V%x.0\n", CPLD_READ(cpld_ver),
CPLD_READ(cpld_ver_sub), CPLD_READ(pcba_ver));
diff --git a/board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg b/board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg
new file mode 100644
index 0000000..28cd958
--- /dev/null
+++ b/board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# RCW
+0810000f 0c000000 00000000 00000000
+14550002 80004012 60040000 61002000
+00000000 00000000 00000000 00038800
+00000000 00001100 00000096 00000001