include/configs/davinci_sonata.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * Define this to make U-Boot skip low level initialization when loaded
  * by initial bootloader. Not required by NAND U-Boot version but IS
  * required for a NOR version used to burn the real NOR U-Boot into
  * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
  * so it is NOT possible to build a U-Boot with both NAND and NOR routines.
  * NOR U-Boot is loaded directly from Flash so it must perform all the
  * low level initialization itself. NAND version is loaded by an initial
  * bootloader (UBL in TI-ese) that performs such an initialization so it's
  * skipped in NAND version. The third DaVinci boot mode loads a bootloader
  * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
  * performing low level init prior to loading. All that means we can NOT use
  * NAND version to put U-Boot into NOR because it doesn't have NOR support and
  * we can NOT use NOR version because it performs low level initialization
  * effectively destroying itself in DDR memory. That's why a separate NOR
  * version with this define is needed. It is loaded via UART, then one uses
  * it to somehow download a proper NOR version built WITHOUT this define to
  * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
  * NOR support into the initial bootloader so it won't be needed but DaVinci
  * static RAM might be too small for this (I have something like 2Kbytes left
  * as of now, without NOR support) so this might've not happened...
  *
 #define CONFIG_NOR_UART_BOOT
  */

 /*=======*/
 /* Board */
 /*=======*/
 #define SONATA_BOARD
 #define CONFIG_SYS_NAND_SMALLPAGE
 #define CONFIG_SYS_USE_NOR
 #define MACH_TYPE_SONATA 1254
 #define CONFIG_MACH_TYPE MACH_TYPE_SONATA
 /*===================*/
 /* SoC Configuration */
 /*===================*/
 #define CONFIG_ARM926EJS			/* arm926ejs CPU core */
 #define CONFIG_SYS_TIMERBASE		0x01c21400	/* use timer 0 */
 #define CONFIG_SYS_HZ_CLOCK		27000000	/* Timer Input clock freq */
 #define CONFIG_SYS_HZ			1000
 #define CONFIG_SOC_DM644X
 /*====================================================*/
 /* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
 /* on Sonata/DV_EVM board. No EEPROM on schmoogie.    */
 /*====================================================*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
 /*=============*/
 /* Memory Info */
 /*=============*/
 #define CONFIG_SYS_MALLOC_LEN		(0x10000 + 128*1024)	/* malloc() len */
 #define CONFIG_SYS_MEMTEST_START	0x80000000	/* memtest start address */
 #define CONFIG_SYS_MEMTEST_END		0x81000000	/* 16MB RAM test */
 #define CONFIG_NR_DRAM_BANKS	1		/* we have 1 bank of DRAM */
 #define PHYS_SDRAM_1		0x80000000	/* DDR Start */
 #define PHYS_SDRAM_1_SIZE	0x08000000	/* DDR size 128MB */
 #define DDR_4BANKS				/* 4-bank DDR2 (128MB) */
 /*====================*/
 /* Serial Driver info */
 /*====================*/
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size, byteorder */
 #define CONFIG_SYS_NS16550_COM1	0x01c20000	/* Base address of UART0 */
 #define CONFIG_SYS_NS16550_CLK	CONFIG_SYS_HZ_CLOCK	/* Input clock to NS16550 */
 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
 #define CONFIG_BAUDRATE		115200		/* Default baud rate */
 /*===================*/
 /* I2C Configuration */
 /*===================*/
 #define CONFIG_HARD_I2C
 #define CONFIG_DRIVER_DAVINCI_I2C
 #define CONFIG_SYS_I2C_SPEED		80000	/* 100Kbps won't work, silicon bug */
 #define CONFIG_SYS_I2C_SLAVE		10	/* Bogus, master-only in U-Boot */
 /*==================================*/
 /* Network & Ethernet Configuration */
 /*==================================*/
 #define CONFIG_DRIVER_TI_EMAC
 #define CONFIG_MII
 #define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT	10
 /*=====================*/
 /* Flash & Environment */
 /*=====================*/
 #ifdef CONFIG_SYS_USE_NAND
 #define CONFIG_NAND_DAVINCI
 #define CONFIG_SYS_NAND_CS		2
 #undef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_ENV_OVERWRITE		/* instead if obsoleted forceenv() */
 #define CONFIG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
 #define CONFIG_ENV_SECT_SIZE	512	/* Env sector Size */
 #define CONFIG_ENV_SIZE		(16 << 10)	/* 16 KiB */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
 #define CONFIG_SYS_NAND_BASE		0x02000000
 #define CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
 #define CONFIG_ENV_OFFSET		0x0	/* Block 0--not used by bootcode */
 #elif defined(CONFIG_SYS_USE_NOR)
 #ifdef CONFIG_NOR_UART_BOOT
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
 #else
 #undef CONFIG_SKIP_LOWLEVEL_INIT
 #endif
 #define CONFIG_ENV_IS_IN_FLASH
 #undef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_MAX_FLASH_BANKS	1		/* max number of flash banks */
 #define CONFIG_SYS_FLASH_SECT_SZ	0x20000		/* 128KB sect size AMD Flash */
 #define CONFIG_ENV_OFFSET		(CONFIG_SYS_FLASH_SECT_SZ*2)
 #define CONFIG_ENV_SIZE		CONFIG_SYS_FLASH_SECT_SZ
 #define PHYS_FLASH_1		0x02000000	/* CS2 Base address	 */
 #define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1	/* Flash Base for U-Boot */
 #define PHYS_FLASH_SIZE		0x2000000	/* Flash size 32MB	 */
 #define CONFIG_SYS_MAX_FLASH_SECT	(PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
 #define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_FLASH_SECT_SZ	/* Env sector Size */
 #endif
 /*==============================*/
 /* U-Boot general configuration */
 /*==============================*/
 #define CONFIG_MISC_INIT_R
 #undef CONFIG_BOOTDELAY
 #define CONFIG_BOOTFILE		"uImage"	/* Boot file name */
 #define CONFIG_SYS_PROMPT		"U-Boot > "	/* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size  */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print buffer sz */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
 #define CONFIG_SYS_LOAD_ADDR		0x80700000	/* default Linux kernel load address */
 #define CONFIG_VERSION_VARIABLE
 #define CONFIG_AUTO_COMPLETE		/* Won't work with hush so far, may be later */
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CRC32_VERIFY
 #define CONFIG_MX_CYCLIC
 /*===================*/
 /* Linux Information */
 /*===================*/
 #define LINUX_BOOT_PARAM_ADDR	0x80000100
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_BOOTARGS		"mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
 #define CONFIG_BOOTCOMMAND	"setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2060000"
 /*=================*/
 /* U-Boot commands */
 /*=================*/
 #include <config_cmd_default.h>
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SAVES
 #define CONFIG_CMD_EEPROM
 #undef CONFIG_CMD_BDI
 #undef CONFIG_CMD_FPGA
 #undef CONFIG_CMD_SETGETDCR
 #ifdef CONFIG_SYS_USE_NAND
 #undef CONFIG_CMD_FLASH
 #undef CONFIG_CMD_IMLS
 #define CONFIG_CMD_NAND
 #elif defined(CONFIG_SYS_USE_NOR)
 #define CONFIG_CMD_JFFS2
 #else
 #error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
 #endif

 #ifdef CONFIG_CMD_BDI
 #define CONFIG_CLOCKS
 #endif

 #define CONFIG_MAX_RAM_BANK_SIZE	(256 << 20)	/* 256 MB */

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + \
 					 CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* Define this to make U-Boot skip low level initialization when loaded
	* by initial bootloader. Not required by NAND U-Boot version but IS
	* required for a NOR version used to burn the real NOR U-Boot into
	* NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
	* so it is NOT possible to build a U-Boot with both NAND and NOR routines.
	* NOR U-Boot is loaded directly from Flash so it must perform all the
	* low level initialization itself. NAND version is loaded by an initial
	* bootloader (UBL in TI-ese) that performs such an initialization so it's
	* skipped in NAND version. The third DaVinci boot mode loads a bootloader
	* via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
	* performing low level init prior to loading. All that means we can NOT use
	* NAND version to put U-Boot into NOR because it doesn't have NOR support and
	* we can NOT use NOR version because it performs low level initialization
	* effectively destroying itself in DDR memory. That's why a separate NOR
	* version with this define is needed. It is loaded via UART, then one uses
	* it to somehow download a proper NOR version built WITHOUT this define to
	* RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
	* NOR support into the initial bootloader so it won't be needed but DaVinci
	* static RAM might be too small for this (I have something like 2Kbytes left
	* as of now, without NOR support) so this might've not happened...
	*
	#define CONFIG_NOR_UART_BOOT
	*/

	/=======/
	/* Board */
	/=======/
	#define SONATA_BOARD
	#define CONFIG_SYS_NAND_SMALLPAGE
	#define CONFIG_SYS_USE_NOR
	#define MACH_TYPE_SONATA 1254
	#define CONFIG_MACH_TYPE MACH_TYPE_SONATA
	/===================/
	/* SoC Configuration */
	/===================/
	#define CONFIG_ARM926EJS /* arm926ejs CPU core */
	#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
	#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
	#define CONFIG_SYS_HZ 1000
	#define CONFIG_SOC_DM644X
	/====================================================/
	/* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
	/* on Sonata/DV_EVM board. No EEPROM on schmoogie. */
	/====================================================/
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
	/=============/
	/* Memory Info */
	/=============/
	#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1281024) / malloc() len */
	#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
	#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
	#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
	#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
	#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
	#define DDR_4BANKS /* 4-bank DDR2 (128MB) */
	/====================/
	/* Serial Driver info */
	/====================/
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */
	#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
	#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */
	#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
	#define CONFIG_BAUDRATE 115200 /* Default baud rate */
	/===================/
	/* I2C Configuration */
	/===================/
	#define CONFIG_HARD_I2C
	#define CONFIG_DRIVER_DAVINCI_I2C
	#define CONFIG_SYS_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
	#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
	/==================================/
	/* Network & Ethernet Configuration */
	/==================================/
	#define CONFIG_DRIVER_TI_EMAC
	#define CONFIG_MII
	#define CONFIG_BOOTP_DEFAULT
	#define CONFIG_BOOTP_DNS
	#define CONFIG_BOOTP_DNS2
	#define CONFIG_BOOTP_SEND_HOSTNAME
	#define CONFIG_NET_RETRY_COUNT 10
	/=====================/
	/* Flash & Environment */
	/=====================/
	#ifdef CONFIG_SYS_USE_NAND
	#define CONFIG_NAND_DAVINCI
	#define CONFIG_SYS_NAND_CS 2
	#undef CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_SYS_NO_FLASH
	#define CONFIG_ENV_OVERWRITE /* instead if obsoleted forceenv() */
	#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
	#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */
	#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
	#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
	#define CONFIG_SYS_NAND_BASE 0x02000000
	#define CONFIG_SYS_NAND_HW_ECC
	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
	#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
	#elif defined(CONFIG_SYS_USE_NOR)
	#ifdef CONFIG_NOR_UART_BOOT
	#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
	#else
	#undef CONFIG_SKIP_LOWLEVEL_INIT
	#endif
	#define CONFIG_ENV_IS_IN_FLASH
	#undef CONFIG_SYS_NO_FLASH
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
	#define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* 128KB sect size AMD Flash */
	#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*2)
	#define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ
	#define PHYS_FLASH_1 0x02000000 /* CS2 Base address */
	#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */
	#define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */
	#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
	#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ /* Env sector Size */
	#endif
	/==============================/
	/* U-Boot general configuration */
	/==============================/
	#define CONFIG_MISC_INIT_R
	#undef CONFIG_BOOTDELAY
	#define CONFIG_BOOTFILE "uImage" /* Boot file name */
	#define CONFIG_SYS_PROMPT "U-Boot > " /* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
	#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */
	#define CONFIG_VERSION_VARIABLE
	#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
	#define CONFIG_SYS_HUSH_PARSER
	#define CONFIG_CMDLINE_EDITING
	#define CONFIG_SYS_LONGHELP
	#define CONFIG_CRC32_VERIFY
	#define CONFIG_MX_CYCLIC
	/===================/
	/* Linux Information */
	/===================/
	#define LINUX_BOOT_PARAM_ADDR 0x80000100
	#define CONFIG_CMDLINE_TAG
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_BOOTARGS "mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
	#define CONFIG_BOOTCOMMAND "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2060000"
	/=================/
	/* U-Boot commands */
	/=================/
	#include <config_cmd_default.h>
	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_DIAG
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_SAVES
	#define CONFIG_CMD_EEPROM
	#undef CONFIG_CMD_BDI
	#undef CONFIG_CMD_FPGA
	#undef CONFIG_CMD_SETGETDCR
	#ifdef CONFIG_SYS_USE_NAND
	#undef CONFIG_CMD_FLASH
	#undef CONFIG_CMD_IMLS
	#define CONFIG_CMD_NAND
	#elif defined(CONFIG_SYS_USE_NOR)
	#define CONFIG_CMD_JFFS2
	#else
	#error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
	#endif

	#ifdef CONFIG_CMD_BDI
	#define CONFIG_CLOCKS
	#endif

	#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
	CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)

	#endif /* __CONFIG_H */