include/configs/T102xRDB.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  * Copyright 2020-2021 NXP
  */

 /*
  * T1024/T1023 RDB board configuration file
  */

 #ifndef __T1024RDB_H
 #define __T1024RDB_H

 #include <linux/stringify.h>

 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_ENABLE_36BIT_PHYS

 #define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
 #define CONFIG_SYS_NUM_CPC		CONFIG_SYS_NUM_DDR_CTLRS

 /* support deep sleep */
 #ifdef CONFIG_ARCH_T1024
 #define CONFIG_DEEP_SLEEP
 #endif

 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_PAD_TO		0x40000
 #define CONFIG_SPL_MAX_SIZE		0x28000
 #define RESET_VECTOR_OFFSET		0x27FFC
 #define BOOT_PAGE_OFFSET		0x27000
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SPL_SKIP_RELOCATE
 #define CONFIG_SPL_COMMON_INIT_DDR
 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif

 #ifdef CONFIG_MTD_RAW_NAND
 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST	0x30000000
 #define CONFIG_SYS_NAND_U_BOOT_START	0x30000000
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
 #endif

 #ifdef CONFIG_SPIFLASH
 #define CONFIG_RESET_VECTOR_ADDRESS		0x30000FFC
 #define CONFIG_SPL_SPI_FLASH_MINIMAL
 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE	(768 << 10)
 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST		(0x30000000)
 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START	(0x30000000)
 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS	(256 << 10)
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
 #endif
 #endif

 #ifdef CONFIG_SDCARD
 #define CONFIG_RESET_VECTOR_ADDRESS	0x30000FFC
 #define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
 #define CONFIG_SYS_MMC_U_BOOT_DST	(0x30000000)
 #define CONFIG_SYS_MMC_U_BOOT_START	(0x30000000)
 #define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
 #endif
 #endif

 #endif /* CONFIG_RAMBOOT_PBL */

 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif

 /* PCIe Boot - Master */
 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 /*
  * for slave u-boot IMAGE instored in master memory space,
  * PHYS must be aligned based on the SIZE
  */
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 #else
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
 #endif
 /*
  * for slave UCODE and ENV instored in master memory space,
  * PHYS must be aligned based on the SIZE
  */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS	 0x3ffe00000ull
 #else
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS  0xffe00000
 #endif
 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE	0x40000 /* 256K */
 /* slave core release by master*/
 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET	0xe00e4
 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK	0x00000001 /* release core 0 */

 /* PCIe Boot - Slave */
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 /* Set 1M boot space for PCIe boot */
 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS	\
 		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 #endif

 #ifndef __ASSEMBLY__
 unsigned long get_board_sys_clk(void);
 #endif

 #define CONFIG_SYS_CLK_FREQ	100000000

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_SYS_CACHE_STASHING
 #define CONFIG_BACKSIDE_L2_CACHE
 #define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
 #define CONFIG_BTB			/* toggle branch predition */
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif

 /*
  *  Config the L3 Cache as L3 SRAM
  */
 #define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
 #define CONFIG_SYS_L3_SIZE		(256 << 10)
 #define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 #define SPL_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
 #define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
 #define CONFIG_SPL_RELOC_MALLOC_SIZE	(30 << 10)
 #define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)

 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
 #endif

 /* EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM	0

 /*
  * DDR Setup
  */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS	0x51
 #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
 #elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_SYS_SDRAM_SIZE   2048
 #endif

 /*
  * IFC Definitions
  */
 #define CONFIG_SYS_FLASH_BASE	0xe8000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 #else
 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
 #endif

 #define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 				CSPR_PORT_SIZE_16 | \
 				CSPR_MSEL_NOR | \
 				CSPR_V)
 #define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)

 /* NOR Flash Timing Params */
 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
 #elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_NOR_CSOR    (CSOR_NOR_ADM_SHIFT(0) | \
 				CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
 #endif
 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
 				FTIM0_NOR_TEADC(0x5) | \
 				FTIM0_NOR_TEAHC(0x5))
 #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
 				FTIM1_NOR_TRAD_NOR(0x1A) |\
 				FTIM1_NOR_TSEQRAD_NOR(0x13))
 #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
 				FTIM2_NOR_TCH(0x4) | \
 				FTIM2_NOR_TWPH(0x0E) | \
 				FTIM2_NOR_TWP(0x1c))
 #define CONFIG_SYS_NOR_FTIM3	0x0

 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}

 #ifdef CONFIG_TARGET_T1024RDB
 /* CPLD on IFC */
 #define CONFIG_SYS_CPLD_BASE		0xffdf0000
 #define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 #define CONFIG_SYS_CSPR2_EXT		(0xf)
 #define CONFIG_SYS_CSPR2		(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 						| CSPR_PORT_SIZE_8 \
 						| CSPR_MSEL_GPCM \
 						| CSPR_V)
 #define CONFIG_SYS_AMASK2		IFC_AMASK(64*1024)
 #define CONFIG_SYS_CSOR2		0x0

 /* CPLD Timing parameters for IFC CS2 */
 #define CONFIG_SYS_CS2_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
 						FTIM0_GPCM_TEADC(0x0e) | \
 						FTIM0_GPCM_TEAHC(0x0e))
 #define CONFIG_SYS_CS2_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
 						FTIM1_GPCM_TRAD(0x1f))
 #define CONFIG_SYS_CS2_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
 						FTIM2_GPCM_TCH(0x8) | \
 						FTIM2_GPCM_TWP(0x1f))
 #define CONFIG_SYS_CS2_FTIM3		0x0
 #endif

 /* NAND Flash on IFC */
 #define CONFIG_SYS_NAND_BASE		0xff800000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
 #else
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
 #endif
 #define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
 				| CSPR_V)
 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)

 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
 #elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
 				| CSOR_NAND_RAL_3	/* RAL 3Bytes */ \
 				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
 				| CSOR_NAND_SPRZ_128	/* Spare size = 128 */ \
 				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
 #endif

 /* ONFI NAND Flash mode0 Timing Params */
 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
 					FTIM0_NAND_TWP(0x18)   | \
 					FTIM0_NAND_TWCHT(0x07) | \
 					FTIM0_NAND_TWH(0x0a))
 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
 					FTIM1_NAND_TWBE(0x39)  | \
 					FTIM1_NAND_TRR(0x0e)   | \
 					FTIM1_NAND_TRP(0x18))
 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
 					FTIM2_NAND_TREH(0x0a) | \
 					FTIM2_NAND_TWHRE(0x1e))
 #define CONFIG_SYS_NAND_FTIM3		0x0

 #define CONFIG_SYS_NAND_DDR_LAW		11
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1

 #if defined(CONFIG_MTD_RAW_NAND)
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 #else
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
 #endif

 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SPL_TEXT_BASE
 #else
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
 #endif

 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_HWCONFIG

 /* define to use L1 as initial stack */
 #define CONFIG_L1_INIT_RAM
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS	0xfe03c000 /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 #endif
 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)

 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)

 #define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
 #define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
 #define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)

 /* Video */
 #undef CONFIG_FSL_DIU_FB	/* RDB doesn't support DIU */
 #ifdef CONFIG_FSL_DIU_FB
 #define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x180000)
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
 /*
  * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
  * disable empty flash sector detection, which is I/O-intensive.
  */
 #undef CONFIG_SYS_FLASH_EMPTY_INFO
 #endif

 /* I2C */

 #define I2C_PCA6408_BUS_NUM		1
 #define I2C_PCA6408_ADDR		0x20

 /* I2C bus multiplexer */
 #define I2C_MUX_CH_DEFAULT	0x8

 /*
  * RTC configuration
  */
 #define RTC
 #define CONFIG_RTC_DS1337	1
 #define CONFIG_SYS_I2C_RTC_ADDR	0x68

 /*
  * eSPI - Enhanced SPI
  */

 /*
  * General PCIe
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CONFIG_PCIE1		/* PCIE controller 1 */
 #define CONFIG_PCIE2		/* PCIE controller 2 */
 #define CONFIG_PCIE3		/* PCIE controller 3 */
 #define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */

 #ifdef CONFIG_PCI
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #ifdef CONFIG_PCIE1
 #define	CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
 #define	CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
 #endif

 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 #ifdef CONFIG_PCIE2
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0x90000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xc10000000ull
 #define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
 #endif

 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 #ifdef CONFIG_PCIE3
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
 #define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
 #endif

 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #endif	/* CONFIG_PCI */

 /*
  * USB
  */
 #define CONFIG_HAS_FSL_DR_USB

 #ifdef CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #endif

 /*
  * SDHC
  */
 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #endif

 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
 #define CONFIG_SYS_BMAN_NUM_PORTALS	10
 #define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
 #else
 #define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
 #endif
 #define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 					CONFIG_SYS_BMAN_CENA_SIZE)
 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08
 #define CONFIG_SYS_QMAN_NUM_PORTALS	10
 #define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
 #else
 #define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
 #endif
 #define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 					CONFIG_SYS_QMAN_CENA_SIZE)
 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08

 #define CONFIG_SYS_DPAA_FMAN

 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */

 #ifdef CONFIG_SYS_DPAA_FMAN
 #if defined(CONFIG_TARGET_T1024RDB)
 #define RGMII_PHY1_ADDR		0x2
 #define RGMII_PHY2_ADDR		0x6
 #define SGMII_AQR_PHY_ADDR	0x2
 #define FM1_10GEC1_PHY_ADDR	0x1
 #elif defined(CONFIG_TARGET_T1023RDB)
 #define RGMII_PHY1_ADDR		0x1
 #define SGMII_RTK_PHY_ADDR	0x3
 #define SGMII_AQR_PHY_ADDR	0x2
 #endif
 #endif

 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_ETHPRIME		"FM1@DTSEC4"
 #endif

 /*
  * Dynamic MTD Partition support with mtdparts
  */

 /*
  * Environment
  */
 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

 /*
  * Miscellaneous configurable options
  */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

 /*
  * Environment Configuration
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	u-boot.bin /* U-Boot image on TFTP server */
 #define __USB_PHY_TYPE		utmi

 #ifdef CONFIG_ARCH_T1024
 #define CONFIG_BOARDNAME t1024rdb
 #define BANK_INTLV cs0_cs1
 #else
 #define CONFIG_BOARDNAME t1023rdb
 #define BANK_INTLV  null
 #endif

 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
 	"bank_intlv=" __stringify(BANK_INTLV) "\0"		\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"  \
 	"ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
 	"fdtfile=" __stringify(CONFIG_BOARDNAME) "/"		\
 	__stringify(CONFIG_BOARDNAME) ".dtb\0"			\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
 	"bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
 	"netdev=eth0\0"						\
 	"tftpflash=tftpboot $loadaddr $uboot && "		\
 	"protect off $ubootaddr +$filesize && "			\
 	"erase $ubootaddr +$filesize && "			\
 	"cp.b $loadaddr $ubootaddr $filesize && "		\
 	"protect on $ubootaddr +$filesize && "			\
 	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
 	"consoledev=ttyS0\0"					\
 	"ramdiskaddr=2000000\0"					\
 	"fdtaddr=1e00000\0"					\
 	"bdev=sda3\0"

 #define LINUXBOOTCOMMAND					\
 	"setenv bootargs root=/dev/ram rw "		\
 	"console=$consoledev,$baudrate $othbootargs;"	\
 	"setenv ramdiskaddr 0x02000000;"		\
 	"setenv fdtaddr 0x00c00000;"			\
 	"setenv loadaddr 0x1000000;"			\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define NFSBOOTCOMMAND			\
 	"setenv bootargs root=/dev/nfs rw "	\
 	"nfsroot=$serverip:$rootpath "		\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 	"console=$consoledev,$baudrate $othbootargs;"	\
 	"tftp $loadaddr $bootfile;"		\
 	"tftp $fdtaddr $fdtfile;"		\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_BOOTCOMMAND	LINUXBOOTCOMMAND

 #include <asm/fsl_secure_boot.h>

 #endif	/* __T1024RDB_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2014 Freescale Semiconductor, Inc.
	* Copyright 2020-2021 NXP
	*/

	/*
	* T1024/T1023 RDB board configuration file
	*/

	#ifndef __T1024RDB_H
	#define __T1024RDB_H

	#include <linux/stringify.h>

	/* High Level Configuration Options */
	#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
	#define CONFIG_ENABLE_36BIT_PHYS

	#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
	#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS

	/* support deep sleep */
	#ifdef CONFIG_ARCH_T1024
	#define CONFIG_DEEP_SLEEP
	#endif

	#ifdef CONFIG_RAMBOOT_PBL
	#define CONFIG_SPL_FLUSH_IMAGE
	#define CONFIG_SPL_PAD_TO 0x40000
	#define CONFIG_SPL_MAX_SIZE 0x28000
	#define RESET_VECTOR_OFFSET 0x27FFC
	#define BOOT_PAGE_OFFSET 0x27000
	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SPL_SKIP_RELOCATE
	#define CONFIG_SPL_COMMON_INIT_DDR
	#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
	#endif

	#ifdef CONFIG_MTD_RAW_NAND
	#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
	#define CONFIG_SYS_NAND_U_BOOT_DST 0x30000000
	#define CONFIG_SYS_NAND_U_BOOT_START 0x30000000
	#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
	#endif

	#ifdef CONFIG_SPIFLASH
	#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC
	#define CONFIG_SPL_SPI_FLASH_MINIMAL
	#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
	#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x30000000)
	#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x30000000)
	#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MPC85XX_NO_RESETVEC
	#endif
	#endif

	#ifdef CONFIG_SDCARD
	#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC
	#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
	#define CONFIG_SYS_MMC_U_BOOT_DST (0x30000000)
	#define CONFIG_SYS_MMC_U_BOOT_START (0x30000000)
	#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MPC85XX_NO_RESETVEC
	#endif
	#endif

	#endif /* CONFIG_RAMBOOT_PBL */

	#ifndef CONFIG_RESET_VECTOR_ADDRESS
	#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
	#endif

	/* PCIe Boot - Master */
	#define CONFIG_SRIO_PCIE_BOOT_MASTER
	/*
	* for slave u-boot IMAGE instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
	#else
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
	#endif
	/*
	* for slave UCODE and ENV instored in master memory space,
	* PHYS must be aligned based on the SIZE
	*/
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
	#else
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000
	#endif
	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
	/* slave core release by master*/
	#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
	#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

	/* PCIe Boot - Slave */
	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
	/* Set 1M boot space for PCIe boot */
	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#endif

	#ifndef __ASSEMBLY__
	unsigned long get_board_sys_clk(void);
	#endif

	#define CONFIG_SYS_CLK_FREQ 100000000

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_SYS_CACHE_STASHING
	#define CONFIG_BACKSIDE_L2_CACHE
	#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
	#define CONFIG_BTB /* toggle branch predition */
	#ifdef CONFIG_DDR_ECC
	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#endif

	/*
	* Config the L3 Cache as L3 SRAM
	*/
	#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
	#define CONFIG_SYS_L3_SIZE (256 << 10)
	#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
	#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
	#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
	#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
	#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)

	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_DCSRBAR 0xf0000000
	#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
	#endif

	/* EEPROM */
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0

	/*
	* DDR Setup
	*/
	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
	#if defined(CONFIG_TARGET_T1024RDB)
	#define CONFIG_SYS_SPD_BUS_NUM 0
	#define SPD_EEPROM_ADDRESS 0x51
	#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
	#elif defined(CONFIG_TARGET_T1023RDB)
	#define CONFIG_SYS_DDR_RAW_TIMING
	#define CONFIG_SYS_SDRAM_SIZE 2048
	#endif

	/*
	* IFC Definitions
	*/
	#define CONFIG_SYS_FLASH_BASE 0xe8000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull \| CONFIG_SYS_FLASH_BASE)
	#else
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
	#endif

	#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
	#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(12810241024)

	/* NOR Flash Timing Params */
	#if defined(CONFIG_TARGET_T1024RDB)
	#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
	#elif defined(CONFIG_TARGET_T1023RDB)
	#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(0) \| \
	CSOR_NAND_TRHZ_80 \| CSOR_NOR_ADM_SHFT_MODE_EN)
	#endif
	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	FTIM0_NOR_TEADC(0x5) \| \
	FTIM0_NOR_TEAHC(0x5))
	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	FTIM1_NOR_TRAD_NOR(0x1A) \|\
	FTIM1_NOR_TSEQRAD_NOR(0x13))
	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	FTIM2_NOR_TCH(0x4) \| \
	FTIM2_NOR_TWPH(0x0E) \| \
	FTIM2_NOR_TWP(0x1c))
	#define CONFIG_SYS_NOR_FTIM3 0x0

	#define CONFIG_SYS_FLASH_QUIET_TEST
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}

	#ifdef CONFIG_TARGET_T1024RDB
	/* CPLD on IFC */
	#define CONFIG_SYS_CPLD_BASE 0xffdf0000
	#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull \| CONFIG_SYS_CPLD_BASE)
	#define CONFIG_SYS_CSPR2_EXT (0xf)
	#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)
	#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
	#define CONFIG_SYS_CSOR2 0x0

	/* CPLD Timing parameters for IFC CS2 */
	#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	FTIM0_GPCM_TEADC(0x0e) \| \
	FTIM0_GPCM_TEAHC(0x0e))
	#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) \| \
	FTIM1_GPCM_TRAD(0x1f))
	#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) \| \
	FTIM2_GPCM_TCH(0x8) \| \
	FTIM2_GPCM_TWP(0x1f))
	#define CONFIG_SYS_CS2_FTIM3 0x0
	#endif

	/* NAND Flash on IFC */
	#define CONFIG_SYS_NAND_BASE 0xff800000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull \| CONFIG_SYS_NAND_BASE)
	#else
	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	#endif
	#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	\| CSPR_V)
	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)

	#if defined(CONFIG_TARGET_T1024RDB)
	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
	\| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
	\| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
	\| CSOR_NAND_PB(64)) /Pages Per Block = 64/
	#elif defined(CONFIG_TARGET_T1023RDB)
	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL 3Bytes */ \
	\| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
	\| CSOR_NAND_SPRZ_128 /* Spare size = 128 */ \
	\| CSOR_NAND_PB(64)) /Pages Per Block = 64/
	#endif

	/* ONFI NAND Flash mode0 Timing Params */
	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) \| \
	FTIM0_NAND_TWP(0x18) \| \
	FTIM0_NAND_TWCHT(0x07) \| \
	FTIM0_NAND_TWH(0x0a))
	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) \| \
	FTIM1_NAND_TWBE(0x39) \| \
	FTIM1_NAND_TRR(0x0e) \| \
	FTIM1_NAND_TRP(0x18))
	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) \| \
	FTIM2_NAND_TREH(0x0a) \| \
	FTIM2_NAND_TWHRE(0x1e))
	#define CONFIG_SYS_NAND_FTIM3 0x0

	#define CONFIG_SYS_NAND_DDR_LAW 11
	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1

	#if defined(CONFIG_MTD_RAW_NAND)
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
	#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
	#else
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
	#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
	#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
	#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
	#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
	#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
	#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
	#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
	#endif

	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
	#else
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#endif

	#if defined(CONFIG_RAMBOOT_PBL)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_HWCONFIG

	/* define to use L1 as initial stack */
	#define CONFIG_L1_INIT_RAM
	#define CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
	/* The assembler doesn't like typecast */
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) \| \
	CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
	#else
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
	#endif
	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)

	/* Serial Port */
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
	#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
	#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

	/* Video */
	#undef CONFIG_FSL_DIU_FB /* RDB doesn't support DIU */
	#ifdef CONFIG_FSL_DIU_FB
	#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_BMP_LOGO
	#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
	/*
	* With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
	* disable empty flash sector detection, which is I/O-intensive.
	*/
	#undef CONFIG_SYS_FLASH_EMPTY_INFO
	#endif

	/* I2C */

	#define I2C_PCA6408_BUS_NUM 1
	#define I2C_PCA6408_ADDR 0x20

	/* I2C bus multiplexer */
	#define I2C_MUX_CH_DEFAULT 0x8

	/*
	* RTC configuration
	*/
	#define RTC
	#define CONFIG_RTC_DS1337 1
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68

	/*
	* eSPI - Enhanced SPI
	*/

	/*
	* General PCIe
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */
	#define CONFIG_PCIE3 /* PCIE controller 3 */
	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */

	#ifdef CONFIG_PCI
	/* controller 1, direct to uli, tgtid 3, Base address 20000 */
	#ifdef CONFIG_PCIE1
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
	#endif

	/* controller 2, Slot 2, tgtid 2, Base address 201000 */
	#ifdef CONFIG_PCIE2
	#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
	#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
	#endif

	/* controller 3, Slot 1, tgtid 1, Base address 202000 */
	#ifdef CONFIG_PCIE3
	#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
	#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
	#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
	#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
	#endif

	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#endif /* CONFIG_PCI */

	/*
	* USB
	*/
	#define CONFIG_HAS_FSL_DR_USB

	#ifdef CONFIG_HAS_FSL_DR_USB
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#endif

	/*
	* SDHC
	*/
	#ifdef CONFIG_MMC
	#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
	#endif

	/* Qman/Bman */
	#ifndef CONFIG_NOBQFMAN
	#define CONFIG_SYS_BMAN_NUM_PORTALS 10
	#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	#else
	#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
	#endif
	#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
	#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
	#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
	CONFIG_SYS_BMAN_CENA_SIZE)
	#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
	#define CONFIG_SYS_QMAN_NUM_PORTALS 10
	#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
	#else
	#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
	#endif
	#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
	#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
	#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
	CONFIG_SYS_QMAN_CENA_SIZE)
	#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08

	#define CONFIG_SYS_DPAA_FMAN

	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
	#endif /* CONFIG_NOBQFMAN */

	#ifdef CONFIG_SYS_DPAA_FMAN
	#if defined(CONFIG_TARGET_T1024RDB)
	#define RGMII_PHY1_ADDR 0x2
	#define RGMII_PHY2_ADDR 0x6
	#define SGMII_AQR_PHY_ADDR 0x2
	#define FM1_10GEC1_PHY_ADDR 0x1
	#elif defined(CONFIG_TARGET_T1023RDB)
	#define RGMII_PHY1_ADDR 0x1
	#define SGMII_RTK_PHY_ADDR 0x3
	#define SGMII_AQR_PHY_ADDR 0x2
	#endif
	#endif

	#ifdef CONFIG_FMAN_ENET
	#define CONFIG_ETHPRIME "FM1@DTSEC4"
	#endif

	/*
	* Dynamic MTD Partition support with mtdparts
	*/

	/*
	* Environment
	*/
	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */

	/*
	* Miscellaneous configurable options
	*/

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	/*
	* Environment Configuration
	*/
	#define CONFIG_ROOTPATH "/opt/nfsroot"
	#define CONFIG_BOOTFILE "uImage"
	#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
	#define __USB_PHY_TYPE utmi

	#ifdef CONFIG_ARCH_T1024
	#define CONFIG_BOARDNAME t1024rdb
	#define BANK_INTLV cs0_cs1
	#else
	#define CONFIG_BOARDNAME t1023rdb
	#define BANK_INTLV null
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
	"bank_intlv=" __stringify(BANK_INTLV) "\0" \
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
	"ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
	"fdtfile=" __stringify(CONFIG_BOARDNAME) "/" \
	__stringify(CONFIG_BOARDNAME) ".dtb\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
	"bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
	"netdev=eth0\0" \
	"tftpflash=tftpboot $loadaddr $uboot && " \
	"protect off $ubootaddr +$filesize && " \
	"erase $ubootaddr +$filesize && " \
	"cp.b $loadaddr $ubootaddr $filesize && " \
	"protect on $ubootaddr +$filesize && " \
	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"fdtaddr=1e00000\0" \
	"bdev=sda3\0"

	#define LINUXBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"setenv ramdiskaddr 0x02000000;" \
	"setenv fdtaddr 0x00c00000;" \
	"setenv loadaddr 0x1000000;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_BOOTCOMMAND LINUXBOOTCOMMAND

	#include <asm/fsl_secure_boot.h>

	#endif /* __T1024RDB_H */